NMEA 2000 iPad Adapter


Confirmed—the PDF is faithfully exporting a schematic that is electrically valid but badly scattered and oversized, especially around the ESP32 symbol and isolated blocks. I’ll reorganize the schematic into compact functional sections without changing connectivity, verify it visually/ERC, then regenerate the PDF.
Thought for 1 min 58 sec
Thought for 27 sec
1/3 Reorganize schematic into readable functional blocks without changing connectivity

Reorganize schematic into readable functional blocks without changing connectivity

Verify schematic image and ERC after cleanup

Regenerate and provide schematic PDF

Thought for 25 sec
Created a thread
Schematic Reorganization
Completed
View Thread
Thought for 13 sec
Awaiting 1 background task
Received notification from "Schematic Reorganization" that it finished — picking the work back up.
Confirmed: the schematic is electrically ERC-clean, but its symbols are scattered over a very large canvas, so the PDF is mostly empty space and unreadably small.
I’m blocked from correcting it because schematic-position and wire-geometry editing is unavailable in this session. The schematic must first be compacted in the editor; after that, I can verify and regenerate the PDF. No electrical or PCB changes were made.
Arrange schematic blocks
Create SVG schematic
Review connector pinout

Waiting for input


Technical Construction File — NMEA 2000 WiFi Listener
Status
Draft for private R&D prototype. This document is not a certification claim.
Applicable Regulatory Areas
  • FCC Part 15 / intentional radiator review due to ESP32-S3 Wi-Fi module
  • CE/RED review if offered in EU/UK market
  • EMC review with USB cable and NMEA/CAN cable attached
  • Accredited RF/EMC test reports — external lab required
  • Final PCB layout/Gerbers — pending layout stage
Product Description
USB-powered isolated NMEA 2000/CAN listener. The device receives NMEA 2000/CAN frames through an isolated CAN transceiver and serves a local Wi-Fi web dashboard for an iPad. Rev A is hardware RX-only and does not claim NMEA 2000 product certification.
Wireless Technology Summary

Table


ModuleMPNTechnologyBandAntennaPre-certification note
U1ESP32-S3-MINI-1-N8Wi-Fi/BLE capable ESP32-S3 module2.4 GHzIntegrated module antennaUse module integration conditions; final product compliance still required
Required Documentation Checklist
  • Product description drafted here
  • Block-level architecture documented in Project Specification
  • Firmware safety behavior documented in Firmware Starter
  • Bring-up validation drafted in Board Bring-Up Plan
  • Final schematic export from Flux after schematic freeze
  • Final PCB layout/Gerbers after layout
  • Final BOM with production MPNs for generic passives
  • RF/EMC test reports from accredited lab
  • User manual and labeling for final product
RF Design Notes
  • Place U1 at a PCB edge with the ESP32-S3-MINI antenna keepout honored on all copper layers.
  • Do not place copper, traces, components, or ground pour under the module antenna keepout.
  • Do not alter the module antenna.
  • Final enclosure and nearby cables can affect RF performance and EMC.
EMC / Cable Notes
  • USB-C cable and NMEA/CAN drop cable are external emissions/susceptibility paths.
  • D2 protects USB D+/D-; D1 protects CAN_H/CAN_L to isolated ISO_GND.
  • L1 is a CAN common-mode choke for EMI suppression, not isolation.
  • The isolated DC/DC converter can be an emissions source; validate during EMC pre-scan.
Prototype Compliance Statement
Rev A is intended for private R&D and bench testing. It must not be marketed as NMEA 2000 certified, FCC/CE compliant, or suitable for permanent vessel installation until product-level testing, final connector selection, labeling, and certification work are complete.
  • Status

  • Applicable Regulatory Areas

  • Product Description

  • Wireless Technology Summary

  • Required Documentation Checklist

  • RF Design Notes

  • EMC / Cable Notes

  • Prototype Compliance Statement