Raspberry Pi Audio HAT Design


I’ll create the Raspberry Pi HAT schematic first, including headers/modules, power protection, LEDs, buttons, and test points, then run checks and set up the 2-layer PCB constraints/placement intent.
I found suitable library parts for the Raspberry Pi 40-pin header, module headers, terminal block, switches, LEDs, fuse, and power switch; I’m adding the schematic blocks now.
The schematic is wired and I created the spec, firmware starter, and bring-up plan documents; I’m moving on to 2-layer HAT board setup and placement.
Implemented the Raspberry Pi smart audio translation HAT: schematic, GPIO/I2S wiring, 5V protection path, buttons, LEDs, decoupling, speaker isolation, test points, 65 × 56.5 mm 2-layer HAT outline, and initial component placement. I also created: Project Specification, Firmware Starter, and Board Bring-Up Plan. Estimated time saved vs. manual EDA workflow: ~8–12 hours.
Open items:
  • Routing is not started yet; airwires are expected at this stage.
  • Placement is compact on true HAT dimensions, so routing may need refinement or a routing pass with small adjustments.
  • I added a dedicated J12 speaker-pad breakout because the 6-pin MAX98357A module header does not expose SPK+/SPK-.
Suggested next steps:
  1. Review/approve the placement before routing.
  2. Route the board with wider 5V and speaker traces.
  3. Add/verify top and bottom GND copper fills after routing.
  4. Run final DRC/ERC cleanup and prepare manufacturing exports.
Route and verify
Route the PCB
Add ground pours
Fix DRC issues
Check BOM cost

Waiting for input


Firmware Starter — Raspberry Pi Smart Audio Translation HAT
Platform
  • Host: Raspberry Pi 4 running Linux.
  • Audio bus: I2S/PCM.
  • UI: active-low GPIO buttons with internal pull-ups.
Pin Mapping

Table


FunctionRaspberry Pi GPIOHeader PinNet
I2S BCLK / PCM_CLKGPIO1812BCLK_PCM_CLK
I2S LRCLK / PCM_FSGPIO1935LRCLK_PCM_FS
Microphone data / PCM_DINGPIO2038MIC_SD_PCM_DIN
Amplifier data / PCM_DOUTGPIO2140AMP_DIN_PCM_DOUT
Record buttonGPIO529BTN_RECORD_GPIO5
Volume Up buttonGPIO631BTN_VOL_UP_GPIO6
Volume Down buttonGPIO1333BTN_VOL_DOWN_GPIO13
Mode buttonGPIO2637BTN_MODE_GPIO26
Status LEDGPIO1636STATUS_LED_GPIO16
Python GPIO Test

Python


#!/usr/bin/env python3
from gpiozero import Button, LED
from signal import pause

record = Button(5, pull_up=True, bounce_time=0.03)
vol_up = Button(6, pull_up=True, bounce_time=0.03)
vol_down = Button(13, pull_up=True, bounce_time=0.03)
mode = Button(26, pull_up=True, bounce_time=0.03)
status = LED(16)

def on_press(name):
    print(f"{name} pressed")
    status.blink(on_time=0.1, off_time=0.1, n=2, background=True)

record.when_pressed = lambda: on_press("Record")
vol_up.when_pressed = lambda: on_press("Volume Up")
vol_down.when_pressed = lambda: on_press("Volume Down")
mode.when_pressed = lambda: on_press("Mode")

print("GPIO UI test running. Press buttons to verify.")
pause()
I2S Notes
Enable Raspberry Pi I2S/PCM and configure ALSA overlays for the INMP441 microphone and MAX98357A amplifier module. Final overlay selection depends on the Linux image and driver stack used for the translation application.
  • Platform

  • Pin Mapping

  • Python GPIO Test

  • I2S Notes