SHT45 Probe Design


Thought for 9 mins 23 sec
Thought for 9 sec
Reading PCB Release Check's report…
Thought for 8 sec
Reading PCB-B Release Check's report…
Thought for 11 sec — Updating project documentation
Steering SHT45 Probe Design…
Created a thread
SHT45 Probe Design
Completed
View Thread
Thought for 7 sec
Awaiting 1 background task
Received notification from "SHT45 Probe Design" that it finished — picking the work back up.
The preliminary two-board design is now complete and independently verified.
  • PCB-A: 35 × 4 mm, four-layer 1.30 mm preliminary stackup, clean sensor tongue with exactly four 0.15 mm traces, 0 airwires and clean ERC/DRC.
  • PCB-B: standalone TRACE-M8-4P-CARRIER-V1, 13 mm diameter, 1.60 mm two-layer stackup, verified Binder geometry and mapping, fully routed with clean ERC/DRC.
  • All parent documentation is synchronized in Project Specification and Sources/Open Issues.
  • No manufacturing-release files were generated.
Open approval items
  • CM confirmation of the thin four-layer PCB-A stackup; 1.30 mm exceeds the preferred 0.6 mm.
  • PCB-B annular-ring and finished-thickness approval.
  • Enclosure, seal, connector load-path, solder-access and strain-relief validation.
  • First-article electrical, I²C, harness and pull testing.
Next steps
  1. Send both boards to a CM for DFM/stackup review.
  2. Finalize and fit-check the enclosure.
  3. Incorporate CM feedback and run the release review.
  4. Generate manufacturing files only after explicit approval.
Prepare CM review
Design enclosure
Evaluate thinner PCB-A
Plan prototype testing

Sensirion Handling and Packaging
Mandatory factory rules
  • ESD controls are mandatory throughout receiving, kitting, placement, rework, test and packaging.
  • Do not apply board wash or expose the sensor to cleaning agents, alcohols, ketones, solvents, strong air blasts, oils, fingerprints, uncured polymers, flux residues, or concentrated VOCs.
  • Use no-clean type ≥3 solder paste and assemble SHT45 in the last reflow cycle.
  • No ultrasonic cleaning is permitted by project policy. The current SHT handling document does not explicitly use the word ultrasonic, so this is a conservative product requirement rather than a quoted Sensirion statement.
  • Do not touch, press, wipe aggressively, clamp, gasket-load, or use the membrane/package as an axial stop.
Coating and potting control
  • Dimensioned PCB no-coat zone: entire sensor end from the exposed tip through the end of the narrowed neck, approximately the first 9 mm of the 35 mm blade in the current layout; enlarge to include all of U1/C1 and the isolation transition on the released drawing.
  • No coating on top, sides, membrane, underside keepout, or airflow cavity around U1.
  • Coating/potting is allowed only at the connector/rear section after material compatibility and cure/outgassing validation.
  • Use a physical mask and inspection witness; do not rely on operator aiming.
  • Do not use adhesive-lined heat shrink, hot melt, silicone, epoxy or label adhesive near the sensor/neck unless fully cured and qualified.
Reflow and rework
  • Use a qualified Pb-free convection profile per J-STD-020; current Sensirion handling guidance allows peak 260 °C for up to 30 s.
  • Manual sensor soldering is not the production method. If exceptional rework is authorized, limit local solder contact to 5 s at up to 350 °C and protect the membrane from hot-air blast.
  • Expect a temporary negative RH offset after reflow. Do not set tight final RH limits immediately after soldering without rehydration/conditioning.
Storage and packaging
  • Keep sensors in original sealed packaging until use and process within the manufacturer-recommended shelf period.
  • Use metal-in shielded ESD bags, clean paper/cardboard, or qualified PE/PET/PP trays.
  • Do not use ordinary antistatic polyethylene bags, bubble wrap, foam, or large adhesive labels inside the sealed package.
  • Package only after all adhesives, inks, coatings and potting are fully cured and the assembly has been ventilated.
  • Include a clean, non-shedding tip guard that does not contact the membrane and is removed before use.
Conditioning and reconditioning
  • Normal post-reflow recovery can occur over several days at approximately 50–70 %RH.
  • If a formal reconditioning process is needed, current handling guidance suggests baking at 100–105 °C and <5 %RH for 10 h, then rehydrating at 20–30 °C and about 75 %RH for 12 h.
  • Apply that process only to an assembly whose PCB, connector, wires and materials are rated for it; otherwise recondition bare sensor/PCBAs before enclosure assembly or use the slower ambient recovery route.
  • Reconditioning is recovery, not a substitute for contamination prevention.
  • Mandatory factory rules

  • Coating and potting control

  • Reflow and rework

  • Storage and packaging

  • Conditioning and reconditioning