Schematic Analysis and Design Issues

flux

1:01

Below is an analysis of the provided schematic based on the actual connections and the reported airwire errors. Note that these issues are specific to the current schematic connections and component assignments:

Identified Issues and Recommendations

IssueExplanationRecommended Correction
Ambiguous net labelsThe nets are named “Net 1”, “Net 2”, and “Net 3” instead of using descriptive names (e.g. VIN, VOUT, GND). This can cause confusion when verifying proper interconnections.Rename the nets to something more descriptive. For example: assign U1:VI and C1’s corresponding pad to VIN, U1:VO and C2’s corresponding pad to VOUT, and U1:GND (and the remaining pads) to GND.
Duplicate pin naming on U1The LM1117 regulator (U1) shows two pads labeled VO (pins 2 and 4). Some datasheets indicate that multiple output pads are provided for thermal dissipation and current sharing, but the symbol must reflect that these output pads are internally tied.Ensure that the schematic symbol defines both VO pins as a common node – if not, merge them explicitly by labeling them identically. Verify this against the LM1117 datasheet.
Reported airwire error between U1:2 and C2:1The airwire error suggests that although C2:1 and U1:2 both belong to the output node, the tool is indicating an unconnected airwire. This could be due to the tool not recognizing the duplicate VO connection.Double-check that the symbol for U1 properly merges both output pads. An explicit net label (e.g. VOUT) can assist the tool in recognizing a single common node.
Reported airwire error between U1:3 and C1:1Similar to the output, the input side (U1:VI and its decoupling capacitor C1) is flagged. The error might indicate that the connection is made only by net naming without a proper explicit connection (e.g. a supply symbol).Verify that U1:VI is treated as the input node. It’s advisable to apply an explicit label such as VIN to both U1:VI and C1:1 to ensure the tool recognizes them as connected.
Reported ground airwire errors (e.g. U1:1 and C1:2, C2:2)Although C1:2 and C2:2 are on the same net as U1:GND, airwire errors are reported. This could be caused by the absence of an explicit ground symbol or a misinterpreted connection in the schematic editor.Add a dedicated ground reference symbol for the GND net and verify that all ground-related pads (U1:GND, C1:2, C2:2) use the same net label.
Additional Considerations
  • Decoupling Capacitors:
    Both decoupling capacitors (10µF) are placed across the input and output. For an LM1117 regulator, the datasheet typically recommends a low ESR capacitor placed very close to the device. Ensure that the layout minimizes trace lengths from the regulator’s pins to the capacitors.
  • Signal Integrity:
    The schematic does not include additional resistors (such as pull-ups or current limiting resistors); while not strictly required for a regulator, be sure that any further analog or digital interfaces downstream follow best practices (if added later).
  • Pin Assignment Verification:
    Verify the LM1117 pin assignments against its datasheet. In some packages, the pin order might vary; ensure that pin 1 (GND) is connected to the ground net and that the inputs/outputs are correctly assigned to the decoupling capacitors.
Next Steps
  1. Update Net Labels: Rename “Net 1”, “Net 2”, and “Net 3” to VIN, GND, and VOUT (or similar) as appropriate.
  2. Verify U1 Symbol:
    • Ensure that both VO pins (pins 2 and 4) are merged into one common node.
    • Confirm that the datasheet pinout matches the schematic.
  3. Add Explicit Ground Symbol:
    • Place a dedicated ground symbol on the schematic for GND to remove any ambiguity.
  4. Confirm Capacitor Placement:
    • Verify that the decoupling capacitors are placed as close as possible to U1’s pins in both the schematic symbol and the physical layout.
  5. Run a New DRC: After these corrections, run the design rule check again to verify that all airwire errors are resolved.
By applying these specific corrections, the schematic should better reflect the intended operation of the LM1117 regulator and its associated decoupling network while eliminating connection errors reported by the tool.
Rename nets descriptively
Confirm LM1117 symbol
Add explicit ground connection
Ensure datasheet adherence
Re-check DRC
420 days
Sign up to send
C2
Capacitance
10uF
3v3
U1
C1
Capacitance
10uF
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    15.8k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

LM1117 output regulator

LM1117 output regulator thumbnail
LM1117 Output Regulator

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor

Qty 1

Arrow

$0.43–$0.81

Digi-Key

$0.49–$1.17

LCSC

$0.18

Mouser

$1.01

Verical

$0.49–$0.60

Controls