PCB Stackup Repair


Jag stoppade den parallella routingchatten för att undvika samtidiga layoutändringar och verifierade livekortet.
Senast verifierade status
  • Kort: 80 × 50 mm, fyra kopparlager
  • 5 airwires återstår:
    • I2C_SCL → U1:IO9
    • LAMP_CTRL → U1:IO6
    • LED_STATUS → U1:IO10
    • MIST_RESERVED → U1:IO5
    • MOTOR_PWM → U1:IO2
  • 0 redundanta trace-grupper
  • Ingen komponentplacering eller kortkontur ändrades i denna session.
Jag startade ett avgränsat routingjobb för de fem anslutningarna, med krav att bevara stackup, befintlig routing, antennkeepout och J9 DNP. Jobbet hann inte rapportera eller verifieras, så jag kan inte bekräfta om det hann göra några ändringar. Nästa steg är därför att läsa livekortet igen, hämta jobbets rapport och köra slutlig airwire-/DRC-kontroll.
Execution stopped because your ACUs ran out.
"PCB Airwire Routing" completed.
Executortråden är klar, men jag kunde inte läsa dess rapport eller verifiera ändringarna mot livekortet under denna session. Därför är det fortfarande obekräftat om de fem tidigare airwires har routats korrekt.
Återstående arbete:
  • Läs executorrapporten och kontrollera vilka spår som faktiskt lades till.
  • Kör en ny airwire-räkning och full DRC.
  • Bekräfta att fyralagers-stackupen, 80 × 50 mm-konturen, befintlig placering, antennkeepout och J9 DNP fortfarande är intakta.
  • Åtgärda eventuella återstående fel utan onödig omrouting.
Inga ytterligare projektändringar gjordes här. Execution stopped because your ACUs ran out.

Waiting for input


Pre-Meeting Layout Status
Stop checkpoint — 2026-10-20, last full read 05:26:48.385Z
NOT ready to fabricate. Work stopped immediately after a persisted decoupler move, before local copper restoration or final verification. The last mutation explicitly introduced an overlapping-copper finding. Do not assume zero airwires, zero shorts, or production readiness. No export was generated. Execution was stopped by the platform because the account ran out of ACUs; the tools did not fail with a guessed cause.
This report is a partial meeting handoff, not a manufacturing release. The lead must independently verify all final changes. The earlier routing-closure-and-export-readiness file remains historical; the following is newer.
Before/after evidence

Table


MilestoneNative evidenceCounts / limitations
Initial broad DRC + placement + ERC request, 2026-10-20T05:18:35.790ZFresh error/warning-filtered check7 errors: 1 via-in-pad, 1 U1 keepout, 5 C10/C13 neckdown. 43 warnings: 1 U1 body overhang, 6 decoupling, 33 silk, 3 neckdown. No ERC error/warning category was returned; that is not a separately demonstrated successful full ERC run.
Initial standalone routing_stateExplicit fresh read0 airwires; 0 redundant traces.
After C9 move and local redundant-trace deletion, 2026-10-20T05:21:20.912ZAirwires, Redundant Traces, Overlapping Copper, Via In PadAll four categories explicitly Success, 0 errors/warnings. C9 repair verified.
After antenna-zone correction, 2026-10-20T05:25:11.216ZAirwires, Via In Pad, Protected Intrusions; Keepout ViolationsFirst three explicitly Success; keepout still 1 Error at U1. No exemption or rule suppression used.
After FIRST C10/C13 placement, 2026-10-20T05:26:48.385ZScoped fresh Airwires/Redundant/Overlapping Copper + Neckdown/Decoupling request1 airwire Error, 1 redundant-trace Warning group (4 nodes); 3 neckdown Errors and 1 neckdown Warning; 4 decoupling Warnings. This is not broad final DRC.
After SECOND C10/C13 placement — latest persisted statePost-mutation comparison only; no subsequent fresh check possibleIntroduced 1 Overlapping Copper finding; introduced 2 Overlapping Components findings (U4, C10), despite placement summary saying zero changed-component overlaps and 2 pre-existing overlaps. These outputs conflict and need an independent exact read. Resolved 1 C10 neckdown issue; introduced 1 silk issue and resolved another. U1 keepout and body overhang remain. Final total counts and airwires unknown.
Switching-stage errors were absent initially; the regulator cluster was not moved in this pass. No broad autoroute, part replacement, board resize, stackup edit, schematic/net/GPIO mutation or high-current width edit was made.
Applied changes
1. C9 via-in-pad repair — COMPLETED and verified
Original problematic via: 588ff0a6-6bc8-4616-90ca-75f660335e4e.throughHole.0-0, GND, parent smart-via position (-29.4, 19.8) mm. A first atomic removeAndReroute attempt on its parent UID was rejected with: Node uid(s) ... are protected and were not removed. Unprotect them first. Nothing was removed. The via was not unprotected or moved.
A genuinely different supported remedy moved C9 UID 67824ae1-b6e2-4e45-a065-cbecdc1936db from (-29.196, 19.37) to (-29.196, 18.57) mm, preserving Bottom layer/rotation. It cleared the via overlap. Routing_state remained 0 airwires, with 4 newly redundant old escapes, then those exact four trace nodes were deleted in one supported delete_traces call:
  • GND: 2705b3c3-da0b-4531-91b9-52738efba47e, 827cf448-7371-4454-abbd-d9722b972373, 833ef148-4cec-4a33-a38e-9eb7bd1e90e5.
  • 3V3: f08055c4-5ffe-41a5-a9f3-51ad201b3ff4.
Fresh check at 05:21:20.912Z explicitly confirmed zero airwires, redundant traces, shorting copper and via-in-pad findings. No new route was required at that milestone. The pre-existing Top GND bridge from (-29.4,19.8) toward (-29.7,18.35), described in the earlier report, was not removed in this pass.
2. Antenna datum correction — APPLIED; own-body checker finding remains
Important correction to earlier reports: the authoritative Espressif KiCad footprint defines a 13.2 × 5.4 mm antenna keepout, not the previously tentative 13.2 × 3.1 mm interpretation. Official source read directly:
ESP32-C3-MINI-1 official Espressif footprint, repository main resolved to dd76561812ab during this session. Its all-copper-layer antenna keepout prohibits tracks, vias, pads, copperpour and footprints, with corners (±6.6,-2.9) and (±6.6,-8.3) mm in KiCad coordinates. Official outline y=-8.3…8.3; pad 3 at (-5.9,0.3), pad 36 at (4.8,-2.2); all pad sizes are positive.
Registration to actual native U1 footprint was established using two matching physical pad datums, not the 3D model: native pad3/3V3 is local(-5.9,+2.4); native top ground row corresponding to pad36 is local(+4.8,+4.9). Thus native Y=2.7−Yref. U1 remains at (2,19.2), rotation0, Top, so world Y=21.9−Yref. This maps the antenna rectangle to:
  • world x=-4.6…8.6 mm, y=24.8…30.2 mm;
  • center (2,27.5) mm, size 13.2 × 5.4 mm;
  • board edge y=25 mm: nominal antenna begins 0.2 mm inside the board and mostly overhangs.
Changed only position and size rules of existing zone UID 94396a2a-93a0-43cb-8324-f486af5cef41 from (2,23.55),13.2×2.9 to (2,27.5),13.2×5.4. All connectedLayers and keepOut exclusions were left untouched. The old zone incorrectly covered the top ground/terminal region. This is a source-grounded correction and expansion of the true antenna region, not a moved-outside-body workaround. No U1 move or replacement occurred.
Fresh native Keepout Violations still reports U1 itself. Its own antenna body necessarily overlaps its antenna region, consistent with the official footprint's embedded antenna zone. No supported own-module exemption was established or applied; retain this as an unresolved checker/representation item, not evidence that unrelated copper intrusion is safe. Need final read-only validation of zone rules and all-layer copper/via exclusion after the last moves. The native image after correction visibly showed the antenna zone over the correct overhanging antenna section, with module pad row below it.
Datasheet query on official datasheet v2.2 returned partially_answered and did NOT verify the requested pad-row datum; its supported conclusion was to use land-pattern source files for unspecified dimensions. The subsequent direct official footprint read supplied the required registration facts. Do not repeat the old 3.1mm claim. Official guidance also requires RF/housing clearance review: Espressif module layout guidance; no enclosure/RF performance verification was run.
3. C10/C13 decoupling — PARTIAL, affected routing NOT restored

Table


ComponentOriginal placementFirst moveLatest persisted placement
C10 34bb3a1a-1f70-41c1-abee-84d1792cb997Bottom, (-5.8083,16.1),0°Top,(-6.3,20.825),270°Top,(-5.9,21.6),180°
C13 cf982f64-3dc1-45eb-97a8-e0e913e060f2Bottom,(5.5,-3.5),90°Top,(-1.3,-3.65),180°Top,(-1.0,-3.65),180°
The first pass removed both original opposite-layer errors and C13's A-fanout blockage, and cleared both C10/C13 decoupling-loop warnings. Fresh neckdown then found C10 blocking IO2 and 1.33mm too far; C13 0.13mm too far, with a ground-facing warning suggesting0°. The second pass changed C10 to horizontal power-facing orientation and shifted C13 0.3mm toward VCC. Postmutation resolved one C10 neckdown finding but added shorting copper and component-overlap findings. Do not keep moving blindly; two genuine geometry passes have been used. Diagnose exact live blockers before further changes.
Known likely affected copper to inspect first: existing 3V3 Top rail trace 729b275b-a09b-48b7-bea9-42683a8f2bdd from (-4.6,21.6) to (-24.2,21.6). At latest C10 rotation180°, power P1 should be toward U1 on the right and GND P2 on the left; the old straight 3V3 rail crosses the intended new GND-pad area. This crossing was anticipated but routing was not reached before interruption. Confirm the exact check UID pair rather than assume this is the only new short. A scoped atomic removeAndReroute of this affected 3V3 segment, with the C10 GND pad/clearance treated as obstruction, is the intended next supported operation, not broad net reroute.
Fresh airwire before the last move was U4 VCC → C13 P1, net5V. Exact endpoints:
  • U4 VCC 12d75731-abd9-4c35-9b57-76f981942eff__843bb744-4e79-47a1-820f-2f4ed4ad62ac, world(0.55,-3.65), Top.
  • C13 P1 cf982f64-3dc1-45eb-97a8-e0e913e060f2__5237503d-4662-b83a-7859-31969858b9c0.
Native read verified U4 GND(2.45,-2.35), A(2.45,-3.0), Y(0.55,-2.35). C13 must not obstruct A or compromise existing USB/high-current copper. Retain frozen netlist.
The first-pass fresh redundant group contained these four nodes; not deleted yet, and must refresh before deletion because the second move may change redundancy: 03b98b76-f294-4a7f-baf0-068358e0cb98, 3c7257e1-8477-4e53-badc-f76e38d15142, a29cba8b-4e34-49e5-b54e-98fe908add0f, b00ea446-3121-4fb4-9615-05ab11102780.
Read-only SVG pin labels for Bottom generic passives have a known mirrored-coordinate discrepancy relative to effective routed copper. Use actual computed terminal/net mapping plus route geometry, not just SVG text, especially if restoring the original Bottom placements.
4. Silk cleanup — UNATTEMPTED
Loaded silk-label/rules procedure and obtained live UID-specific suggestions, but no silk rule was edited. Initial 33 warnings remain a baseline only; final count changed with cap moves and is unverified. Label-only cleanup must not move electrical components. Use fresh findings; apply individual UID-selector text position/rotation rules, not whole-component rules; readable designators ≥about0.8mm text with about0.15mm strokes. Values may be hidden if needed with supported label-only active=false overrides, never disable components.
Preserved constraints / verification limits
  • Read-only native SVG reconfirmed a closed rounded-rectangle 80×50mm outline, extents x±40,y±25, and custom four-copper-layer stackup, total nominal1.30mm. No board/stackup change in this pass.
  • All changes confined to C9,C10,C13 placement, four C9 stale traces and antenna zone geometry. No schematic/GPIO/net edits, high-current trace-width edits, part replacements or full-board routing.
  • J9/Q4/D5/R20/R21 assembly DNP/exclusion properties were not modified; fresh property audit was not completed. Earlier verified exclusion was BOM/PnP, not footprint deletion. Lead should confirm current properties.
  • U1 native pad tree read showed positive-area physical NC lands (0.4×0.8mm), perimeter GND lands and 0.7×0.7mm corner lands; center GND read showed1.45×1.45mm. Do not equate an NC name with a virtual zero-area pad.
  • Prior KiCad export's21 zero-size pads and legacy-zone warnings were not mapped or rechecked; no export authorized. Their physical-versus-virtual classification remains unknown. Current native positive NC geometry means historical zero-size export issues cannot be dismissed as harmless NCs.
  • Generic L1 production part/footprint choice, feedback route lengths/current capacity, residual C5/C6 loop warnings and manufacturing missing-MPN findings from earlier reports remain independent engineer-review risks; none was silently waived.
Concrete engineer / lead resume actions
  1. Before meeting, obtain exact live broad DRC/placement/ERC and routing_state. Board currently has an introduced overlapping-copper finding and cannot be presented as electrically clean.
  2. Inspect the exact new short and U4/C10 overlap pairs. Repair only the offending 3V3 rail/decoupler escape using supported atomic routing, preserving other routes; restore C13 VCC connection. Read actual pad/layer positions. Do not bypass clearances or suppress checks.
  3. Refresh and delete only proven redundant traces, then verify0 airwires,0 shorting copper and0 via-in-pad. If geometry remains blocked after the bounded passes, document or restore C10/C13 to their original placements (above), clean only newly redundant routes and verify the restored state; retain C9's independently verified repair.
  4. Keep the source-grounded full13.2×5.4mm antenna region. Do not revert to the old incorrect3.1mm hypothesis or shrink zone to silence U1 self-overlap. Resolve supported module-self exemption/checker limitation while preserving all-layer foreign-component/pad/copper/via exclusion. Validate enclosure clearance separately.
  5. Perform label-only cleanup with fresh UID suggestions, up to two attempts per blocker. Keep residual noncritical warnings explicit.
  6. Reconfirm outline, all physical footprints/pad geometry, current J9/mist DNP, antenna enforcement, and final check timestamp. Investigate export pad defects only after separately authorized export/review workflow. No Gerbers in this pass.
Assigned scope status
  • Completed: fresh baseline inspection and explicit initial0-airwire evidence; C9 via-in-pad repair and verified clean connectivity/copper milestone; authoritative antenna datum research and zone correction.
  • Failed / bounded open: U1 own-body keepout finding; supported selective self-exemption not established. C10/C13 closure incomplete with new short/overlap findings and last verified1 airwire before latest move.
  • Unattempted: silk-label cleanup; final full verification/readiness/property audit and historical exported-pad mapping; exports (intentionally not authorized).
  • Overall: partial remediation only. Cannot claim zero blocking errors or a meeting-ready manufacturing release. Execution stopped because ACUs ran out.
  • Stop checkpoint — 2026-10-20, last full read 05:26:48.385Z

  • Before/after evidence

  • Applied changes

  • 1. C9 via-in-pad repair — COMPLETED and verified

  • 2. Antenna datum correction — APPLIED; own-body checker finding remains

  • 3. C10/C13 decoupling — PARTIAL, affected routing NOT restored

  • 4. Silk cleanup — UNATTEMPTED

  • Preserved constraints / verification limits

  • Concrete engineer / lead resume actions

  • Assigned scope status