TLV75733PDBVR Guide


Thought for 6 mins
Thought for 6 sec
Referenced guidance.
Thought for 9 sec
Created 2 tasks.
1/2 Research and write the cited TLV75733PDBVR application guide.
Thought for 17 sec
Awaiting 1 task
Thought for 6 sec
2/2 Check the finished guide for completeness and unsupported claims.

Research and write the cited TLV75733PDBVR application guide.

Check the finished guide for completeness and unsupported claims.

"TLV75733PDBVR Guide" completed.
The guide is drafted, including wiring and thermal cautions; both verified alternatives require lower load current rather than serving as unrestricted replacements. I’m checking the final formatting and citations, with the datasheet revision discrepancy explicitly noted.
Thought for 1 min 32 sec
Thought for 10 sec
Thought for 26 sec
Awaiting 1 task
"TLV75733PDBVR Guide" completed.
Created the TLV75733PDBVR Application and Usage Guide in project files, covering all seven requested sections with citations, practical wiring, thermal cautions, and two pin-compatible alternatives.
Unverified details and the datasheet revision discrepancy are explicitly flagged; neither alternative is an unrestricted replacement.

TLV75733PDBVR Application and Usage Guide
The Texas Instruments TLV75733PDBVR is a fixed 3.3 V, 1 A low-dropout linear regulator with active-high enable, active output discharge, 25 µA typical ground current, and a compact 5-pin DBV/SOT-23 package. Its common use is generating a 3.3 V rail for MCUs, sensors, and other low-voltage loads from a slightly higher low-voltage supply, using only input and output ceramic capacitors.
1. Quick Specifications

Table


AttributeRecommended operating condition / typical performanceAbsolute maximum
Input voltage, VIN1.45 V to 5.5 V−0.3 V to 6 V
Fixed output3.3 VVOUT pin: −0.3 V to the lesser of VIN + 0.3 V or 6 V
Output current0 to 1 ADo not treat 1 A as a thermally unconditional rating
Enable voltage0 to 5.5 V; logic high threshold 1.0 V minimum, logic low threshold 0.3 V maximum−0.3 V to 6 V
Junction temperature−40°C to +125°C−40°C to +150°C; storage −65°C to +150°C
Input/output capacitorsCIN ≥ 1 µF; COUT 1 µF to 200 µF; effective capacitance at each pin must remain >0.47 µF—
Dropout voltage300 mV typical, 425 mV maximum at 1 A and −40°C to +85°C; 475 mV maximum through +125°C—
Ground current25 µA typical, 31 µA maximum at 25°C; 40 µA maximum through +125°C—
Output accuracy±1% for VOUT ≥ 1 V through +85°C; ±1.5% over the wider specified range—
PSRR52 dB typical at 1 kHz, VIN = VOUT + 1 V, IOUT = 50 mA—
PackageDBV, 5-pin SOT-23; 0.95 mm lead pitch; nominal 2.9 mm × 1.6 mm body size is unverified in the attached revision's machine-readable evidence—
Thermal resistanceDBV RθJA = 231.1°C/W under TI's standardized test conditions—
The operating and absolute-maximum limits are distinct: operation outside the recommended range is not guaranteed even when the absolute maximum is not exceeded.
2. Pinout & Connections

Table


Pin NumberPin NameDescriptionBest Practice
1INRegulator supply inputConnect a ≥1 µF X5R/X7R ceramic capacitor directly from IN to GND with a short return path.
2GNDGround reference and power returnConnect to a low-impedance ground plane; return CIN and COUT directly to this ground region.
3ENActive-high enable; VHI is 1.0 V minimum and VLO is 0.3 V maximum.Tie to IN when always on. If driven separately, avoid sustained EN > VIN because EN input current increases; if EN exceeds VIN, keep toggling below 10 kHz.
4NCNo internal connectionLeave unconnected unless a manufacturing rule requires an isolated pad; do not use as a routing tie point.
5OUTFixed 3.3 V regulated outputConnect a ≥1 µF X5R/X7R ceramic capacitor directly from OUT to GND; route to the load with a low-resistance trace or pour.
The exact DBV pin order is IN-1, GND-2, EN-3, NC-4, OUT-5. EN is active high; TI recommends tying EN to IN when shutdown control is unnecessary.
3. Standard Application Circuit
Use the normal fixed-output LDO connection:
  • Supply rail → pin 1 (IN).
  • CIN: 1 µF or larger X5R/X7R ceramic from IN to GND, located at the pins.
  • Pin 2 (GND) → solid ground plane.
  • Pin 3 (EN) → IN for always-on operation, or to a logic/control signal meeting VHI ≥ 1.0 V and VLO ≤ 0.3 V.
  • Pin 4 (NC) → no connection.
  • Pin 5 (OUT) → 3.3 V load rail.
  • COUT: 1 µF or larger X5R/X7R ceramic from OUT to GND, located at the pins.
Both nominal capacitors should be selected so their effective capacitance after DC-bias, tolerance, aging, and temperature remains above 0.47 µF at the IC pins; TI recommends X5R or X7R ceramics and specifies 200 µF as the recommended maximum COUT for best performance. The datasheet does not state a numeric ESR window, so do not invent one; use low-ESR X5R/X7R ceramic capacitors and verify effective capacitance from the capacitor manufacturer's bias curves. When EN is low, the TLV757P connects an internal 120 Ω pull-down from OUT to ground, so ensure the powered load tolerates intentional output discharge.
4. PCB Layout & Routing Guidelines
  • Place CIN and COUT as close as possible to pins 1 and 5, with short, direct ground returns.
  • Use wide traces or copper pours for IN, OUT, and GND; size them for the actual load current and allowable voltage drop rather than relying on minimum design-rule width.
  • Use ground and power copper planes to spread heat; TI specifically recommends copper planes for device connections.
  • Add nearby ground thermal vias where practical to distribute heat into internal/bottom copper, while recognizing that the standard DBV package has no exposed thermal pad.
  • Keep heat-producing parts away from the LDO and evaluate worst-case junction temperature using measured or simulated board thermal performance, not RθJA alone.
5. Common Pitfalls / Things to Watch Out For
  1. Assuming “1 A” means 5 V to 3.3 V at 1 A continuously. That condition dissipates approximately (5 V − 3.3 V) × 1 A = 1.7 W. Multiplying by the datasheet DBV RθJA of 231.1°C/W gives an illustrative standardized-board rise of about 393°C, which is physically incompatible with the +125°C recommended junction limit; actual RθJA is strongly board- and airflow-dependent, but the example shows why thermal design normally limits the usable current well below 1 A at large voltage drops.
  2. Ignoring capacitor bias, EN behavior, or output back-bias. A nominal 1 µF MLCC can fall below the required >0.47 µF effective value; verify DC-bias derating, do not leave EN in an undefined control state, and avoid VOUT > VIN + 0.3 V. Output bias while VIN is absent, a collapsing input with a large COUT, or an externally driven output can produce reverse-current conditions and requires application-specific external protection.

Table


AlternativeClassificationVerified comparison and cautions
Diodes Incorporated AP2112K-3.3TRG1Pin-compatible; standard SOT-23-5/SOT25 package-compatible, but exact land-pattern equivalence was not verified; not an unconditional drop-inSOT25/SOT-23-5 pinout matches exactly: VIN-1, GND-2, EN-3, NC-4, VOUT-5. It is limited to 600 mA, has a 2.5 V to 6 V input range, −40°C to +85°C ambient rating, 1 µF X5R/X7R application capacitors, and different EN thresholds/output-discharge resistance. Use only when the load stays within 600 mA and the narrower temperature/input constraints are acceptable.
Microchip MIC5504-3.3YM5-TRPin-compatible; standard SOT-23-5 package-compatible, but exact land-pattern equivalence was not verified; not an unconditional drop-inSOT23-5 pinout also matches VIN-1, GND-2, EN-3, NC-4, VOUT-5. It guarantees only 300 mA, operates from 2.5 V to 5.5 V, requires ≥1 µF low-ESR ceramic COUT, and has an internal EN pull-down plus a 25 Ω output-discharge load. Use only for ≤300 mA designs after checking startup and EN behavior.
Always compare the exact orderable suffix, land pattern, current, dropout, temperature range, enable thresholds, output-discharge behavior, and capacitor requirements before substitution.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsPrefer TI direct or franchised distributors such as DigiKey, Mouser, Arrow, and Avnet; distributor availability and cut-tape quantities vary by region and date.
Packaging OptionsVerified TI orderable TLV75733PDBVR is large tape-and-reel with a standard pack quantity of 3,000. The reviewed TI datasheet does not list a TLV75733PDBVT small-reel orderable, so a “T” suffix quantity is unverified/not offered in that revision rather than assumed to be 250. Distributor cut tape or custom reels are distributor services, not TI standard pack quantities.
Standard MOQManufacturer reel quantity is not the same as MOQ. TI SPQ is 3,000; actual MOQ for cut tape is distributor-dependent and must be checked at purchase time.
Sourcing AdviceBuy from TI or an authorized/franchised channel, confirm the exact TLV75733PDBVR suffix and date/lot traceability, and avoid unusually cheap broker stock without provenance because relabeled or mishandled semiconductors may be counterfeit. LCSC identifies this device as C485517; JLCPCB lists it as an Extended assembly part and a full reel as 3,000, but live stock, assembly minimums, and pricing are volatile and should be rechecked at order time.
Sources
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources