SMAJ33A Guide


Thought for 12 mins 11 sec
Thought for 6 sec
Referenced guidance.
Thought for 7 sec
Created 2 tasks.
1/2 Verify datasheet ratings, polarity, packaging, and replacement evidence.

Verify datasheet ratings, polarity, packaging, and replacement evidence.

Write and verify the cited application and usage guide.

Thought for 7 sec
Thought for 7 sec
Found 10 results for site.vishay.com SMAJ33A datasheet.
Thought for 31 sec
Awaiting 1 task
"SMAJ33A Guide" completed.
The guide is drafted with cited ratings, wiring, layout, and sourcing guidance. I’m tightening the replacement section so it clearly separates verified functional alternatives from unverified drop-in claims.
Thought for 1 min 20 sec
Thought for 13 sec
Thought for 33 sec
Awaiting 1 task
"SMAJ33A Guide" completed.
Created the SMAJ33A-13-F Application and Usage Guide in the project files, covering specifications, polarity, application wiring, PCB layout, pitfalls, alternatives, and sourcing with citations. Unverified replacement compatibility, surge-waveform details, and purchasing information are explicitly flagged for confirmation before design release.

SMAJ33A-13-F Application and Usage Guide
The Diodes Incorporated SMAJ33A-13-F is a unidirectional 400 W-class transient-voltage-suppression (TVS) diode for shunting short-duration overvoltage energy on rails whose worst-case normal positive voltage remains below 33 V. Its 33 V rating is the reverse stand-off voltage—not the clamp voltage—and the protected circuit must tolerate the specified 53.3 V clamp level plus PCB interconnect overshoot during the applicable surge waveform.
1. Quick Specifications

Table


ClassificationParameterValue / conditionDesign meaning
Normal-condition selectionReverse stand-off voltage, VRWM33 VMaximum continuous reverse working level used to select the protected rail; keep worst-case normal rail peaks below this value.
Normal-condition characteristicReverse leakage, IR5.0 µA maximum at VRWM, TA = 25°CLeakage limit under the datasheet test condition; do not assume the same value over all temperature.
Avalanche characteristicBreakdown voltage, VBR36.7 V minimum to 40.6 V maximum at IT = 1.0 mALow-current breakdown region; not the guaranteed high-current clamp level.
Surge characteristicMaximum clamping voltage, VC53.3 V at IPP = 7.5 AProtected circuitry and insulation must survive at least this voltage plus layout-induced overshoot. Confirm the applicable pulse waveform from the current datasheet's electrical table notes/curves before using 7.5 A in a surge calculation.
Maximum ratingPeak pulse power, PPK400 W, non-repetitive current pulse; derated above TA = 25°CNot a continuous dissipation rating and not transferable to arbitrary pulse shapes or repetition rates; waveform confirmation is required for the intended surge calculation.
Maximum ratingPeak forward surge current, IFSM40 A, 8.3 ms single half-sine wave, superimposed on rated loadApplies to the specified single-event test; it is not a continuous forward-current rating.
Maximum ratingSteady-state power dissipation, PM(AV)1.0 W at TL = 75°CThermal limit under the stated lead-temperature condition.
Maximum ratingJunction temperature, TJ−55°C to +150°CDo not exceed under normal operation or surge heating.
Maximum ratingStorage temperature, TSTG−55°C to +150°C in DS19005 Rev. 19-2Use the revision cited here when reconciling older distributor copies.
IdentificationDevice markingJM for the unidirectional SMAJ33AConfirm both marking and cathode band during inspection.
PackageCaseSMA surface-mount packageTwo-terminal polarized device; verify footprint drawing rather than inferring pad spacing from the body size.
2. Pinout & Connections
The manufacturer identifies polarity by the physical cathode band; it does not define a universal numeric pin convention for every CAD library. Therefore, the numeric mapping below is intentionally CAD-library-dependent and must be verified against the symbol/footprint used in the design.

Table


Pin NumberPin NameDescriptionBest Practice
CAD-dependentK / CathodeBanded end of the unidirectional TVS.Connect to the positive protected rail or incoming positive line. Confirm that the schematic cathode maps to the footprint pad at the package band.
CAD-dependentA / AnodeUnbanded end; surge-current return terminal.Connect to the rail return/chassis-return strategy selected for the interface. Use a short, wide, low-inductance path that does not force surge current through sensitive ground routing.
Polarity rule: for a positive DC rail, place the device in reverse bias with cathode to the positive rail and anode to return. Reversing it makes the diode conduct forward during normal operation. The datasheet's 3.5 V forward-drop statement is specified at 35 A for unidirectional devices, so it must not be treated as a small-current negative-clamp guarantee.
3. Standard Application Circuit

Text


External connector / cable
        +VIN  ────────┬──────────── protected load / regulator input
                       │
                       │ K  (banded end)
                  SMAJ33A-13-F
                       │ A
        RETURN ────────┴──────────── load return
  • This is a shunt protector: under normal voltage it is off except for leakage; during a positive transient it avalanches and diverts current to return.
  • A 24 V rail can be a reasonable candidate only when its tolerance, ringing, charging conditions, and all normal peaks remain below 33 V, and every downstream element can survive the actual clamp voltage plus routing overshoot.
  • No capacitor or series resistor is inherently required by the TVS diode. Add downstream bypassing according to the load/regulator datasheet, and coordinate any fuse, resettable fuse, current limiter, source impedance, or series element with the expected surge energy and fault behavior.
  • Confirm protection with the real threat waveform and source impedance. The 400 W and 7.5 A figures are not continuous ratings and do not certify survival for an arbitrary surge standard.
  • The standard SKU has no verified automotive qualification in the cited datasheet; use an explicitly qualified ordering code when automotive qualification is required.
4. PCB Layout & Routing Guidelines
  • Place the TVS immediately adjacent to the connector or entry point, before long traces or vulnerable circuitry, so the transient is intercepted at the boundary.
  • Minimize the complete surge loop—connector positive to cathode, through the TVS, anode to return, and back to the connector—with short, wide copper and few or no vias.
  • Route the TVS return into a substantial return path or intentional chassis/ground entry structure; do not share a narrow segment with sensitive analog, RF, clock, or reference returns.
  • Avoid thin thermal spokes on the surge-current path. Use copper appropriate for the expected pulse current and verify thermal/current capacity for the selected waveform.
  • The manufacturer's suggested SMA pad layout is C = 4.00 mm, G = 1.50 mm, X = 2.50 mm, X1 = 6.50 mm, and Y = 1.70 mm; interpret these labels with the drawing rather than inventing a terminal pitch. Because capacitance is not guaranteed in the cited electrical table, do not select this part by default for high-speed differential signal lines.
5. Common Pitfalls / Things to Watch Out For
  1. Treating 33 V as the clamp voltage. It is VRWM. Avalanche begins in the 36.7–40.6 V breakdown range at 1 mA, while the specified maximum clamp is 53.3 V at 7.5 A.
  2. Ignoring source energy and layout inductance. A correctly oriented TVS can still fail—or allow the load voltage to exceed 53.3 V—if the pulse energy/repetition exceeds its rating, the source can sustain a DC fault, or long/narrow routing creates additional L·di/dt overshoot.
An alternative is drop-in only after checking the exact ordering code, unidirectional polarity, 33 V stand-off rating, clamp/current values for the same waveform, SMA/DO-214AC land pattern, body tolerances, and cathode orientation. Numeric CAD pin assignments are not universally interchangeable even when the physical package is.

Table


AlternativeVerified compatibilityImportant differences / actionFlux library
Bourns SMAJ33AVerified unidirectional SMA/DO-214AC device with VRWM = 33 V, VBR = 36.7–40.6 V at 1 mA, and VC = 53.3 V at IPP = 7.5 A for a 10/1000 µs pulse. Functionally and nominally footprint-compatible, subject to land-pattern/body-tolerance review.Bourns specifies 1.0 µA maximum leakage at VRWM and separately publishes an 8/20 µs rating; do not mix waveform columns when comparing surge capability.Bourns SMAJ33A
STMicroelectronics SMAJ33A-TRThe primary ST product page lists an active, unidirectional 33 V SMA TVS, making it functionally similar. Drop-in electrical and footprint compatibility are unverified; verify the current ST datasheet's waveform-specific clamp table, polarity, body tolerances, and land pattern before release.Electrical table equivalence was not citation-verified in this guide because the ST PDF indexing remained pending; treat exact surge interchangeability as unverified until checked.ST SMAJ33A-TR
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Manufacturer ordering codeBuy the full SMAJ33A-13-F code to retain the unidirectional A version and the intended tape-and-reel/lead-free suffix. Avoid SMAJ33CA... unless a bidirectional device is intentionally required.
Manufacturer packagingThe Diodes ordering table specifies SMAJXXX(C)A-13-F in tape and reel, 5,000 pieces per reel.
Primary authorized channelsStart with Diodes Incorporated's authorized-distributor network, then check DigiKey and Mouser for traceable stock and cut-tape options; use LCSC/JLCPCB when assembly integration is the priority. Current stock and price are time-sensitive and are not guaranteed by this guide.
Prototype MOQJLCPCB's captured listing reports minimum quantity 1 and full reel 5,000. Manufacturer packaging is 5,000 per tape-and-reel; cut-tape availability and MOQ at DigiKey or Mouser must be confirmed directly at order time.
JLCPCB assemblyLCSC/JLCPCB part C134981; the captured JLCPCB page classifies it for Economic and Standard PCBA and identifies a full reel of 5,000. Check whether the part is Extended or otherwise incurs setup fees in the actual order interface, because classifications can change.
Incoming inspectionVerify MPN label, manufacturer traceability, JM top marking, cathode band orientation, package condition, and reel/date-code records. Do not accept a bidirectional CA version as a silent substitute.
Lifecycle and qualificationThe Flux library lists the Diodes part as active, but purchasing teams should reconfirm manufacturer lifecycle, environmental declarations, and any required qualification at order time. Do not infer automotive qualification from the generic SMAJ family name.
Sourcing adviceFor prototypes, order traceable cut tape from an authorized distributor when available or use the LCSC/JLCPCB assembly listing. For production, compare factory-reel pricing, lead time, date-code policy, authorized-channel traceability, and approved second sources after a controlled equivalence review. Avoid non-authorized marketplaces unless your organization has a documented counterfeit-mitigation process with traceability, inspection, and electrical verification.
Sources
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources