SM24CANB Guide


I’ll research the exact part’s datasheet, pinout, application guidance, and alternatives, then create a cited Application & Usage Guide in the project files.
I found a material source mismatch: this TECH PUBLIC listing is linked to a Littelfuse datasheet, and their published surge ratings differ. I’ll flag that distinction in the guide rather than treat the Littelfuse ratings as verified for C2937019.
Created a project doc

SM24CANB-02HTG Application and Usage Guide

View Document

SM24CANB-02HTG Application and Usage Guide
SM24CANB-02HTG is listed by TECH PUBLIC as a two-channel, bidirectional, 24 V reverse-standoff TVS diode array in SOT-23 for transient protection (LCSC C2937019). Its usual application is shunt protection of CANH and CANL at a CAN-bus connector; the attached Littelfuse datasheet documents that application for Littelfuse’s identically named part.
Read before designing: This project identifies TECH PUBLIC / LCSC C2937019, but its attached datasheet URL points to Littelfuse, not a verified TECH PUBLIC manufacturer document. LCSC and JLCPCB list different surge ratings for C2937019 from those in the Littelfuse datasheet. This guide therefore separa...
Created and checked the SM24CANB-02HTG Application & Usage Guide in the project files, covering all seven requested sections with citations and source links.
Important: The TECH PUBLIC listing is linked to a Littelfuse datasheet with different surge ratings; the guide separates those sources and flags the unverified specifications. Before production, obtain the TECH PUBLIC-controlled datasheet and confirm its pinout and protection limits.

SM24CANB-02HTG Application and Usage Guide
SM24CANB-02HTG is listed by TECH PUBLIC as a two-channel, bidirectional, 24 V reverse-standoff TVS diode array in SOT-23 for transient protection (LCSC C2937019). Its usual application is shunt protection of CANH and CANL at a CAN-bus connector; the attached Littelfuse datasheet documents that application for Littelfuse’s identically named part.
Read before designing: This project identifies TECH PUBLIC / LCSC C2937019, but its attached datasheet URL points to Littelfuse, not a verified TECH PUBLIC manufacturer document. LCSC and JLCPCB list different surge ratings for C2937019 from those in the Littelfuse datasheet. This guide therefore separates distributor-listed TECH PUBLIC specifications from verified Littelfuse reference specifications. Neither identical MPNs nor similar packages establishes identical silicon, automotive qualification, pin mapping, or guaranteed performance. Obtain a manufacturer-controlled TECH PUBLIC datasheet and traceable supplier confirmation before production release; do not qualify C2937019 as a 500 W / 10 A part from the attached document.
1. Quick Specifications
Exact purchasing target: TECH PUBLIC, LCSC C2937019
The following are distributor-listed values, not independently verified manufacturer limits. Classification as absolute maximum, guaranteed minimum/maximum, or typical is unresolved unless explicitly noted below. Sources: LCSC listing and JLCPCB listing.

Table


ParameterListed valueClassification / verification status
Reverse stand-off voltage24 VWorking-voltage listing; manufacturer operating limits unverified
Peak pulse current5.5 A, 8/20 µsPulse-rating listing; absolute-maximum status and temperature derating unverified
Peak pulse power250 W, 8/20 µsPulse-rating listing; not a continuous power rating
Clamping voltage50 VCurrent condition and min/typ/max classification unverified
Breakdown voltage32 VTest current and min/typ/max classification unverified
Reverse leakage current80 nATest condition and limit classification unverified
Junction capacitance17 pFJLCPCB listing; bias, frequency and min/typ/max classification unverified
Operating temperature−55 °C to +125 °CDistributor listing; ambient/junction definition unverified
Channels / polarity2 / bidirectionalDistributor listing
Package / pitchSOT-23 / exact drawing unverifiedDo not infer tolerances or pin mapping from the package name
Attached datasheet reference: Littelfuse SM24CANB-02HTG only
These values are verified for the Littelfuse document, not transferred guarantees for TECH PUBLIC C2937019. Electrical characteristics use TOP = 25 °C.

Table


ParameterValue and test conditionRating category
Peak pulse power, PPk500 W, tp = 8/20 µs Absolute maximum pulse rating
Peak pulse current, IPP10.0 A, tp = 8/20 µs Absolute maximum pulse rating
Operating temperature, TOP−40 °C to +125 °C Listed in Absolute Maximum Ratings; not a separate recommended-conditions table
Storage temperature, TSTOR−55 °C to +150 °C Absolute maximum
Reverse standoff voltage, VRWM24.0 V, IR ≤ 1 µA, pin 1 or 2 to pin 3 Working-voltage characteristic; not the clamp voltage
Reverse breakdown voltage, VBR26.7 V minimum at IT = 1 mA Electrical characteristic
Leakage current, ILEAK0.1 µA maximum at VR = 24 V Electrical characteristic
Clamp voltage, VC34.0 V maximum at 1 A; 46.0 V maximum at 8 A; 50 V maximum at 10 A; tp = 8/20 µs Electrical characteristic, not a recommended operating voltage
Diode capacitance, CI/O-GND30 pF typical, reverse bias = 0 V, f = 1 MHz Typical, not a guaranteed maximum
IEC 61000-4-2 ESD withstand±30 kV contact and ±30 kV air Component test characteristic; not automatic system compliance
PackageSOT23-3, 3 terminals Mechanical / ordering
Lead spacinge = 0.95 mm BSC; e1 = 1.90 mm BSC Package geometry; e1 is the spacing between the two same-side leads
Recommended design use: Keep normal line-to-ground voltages within the selected device’s verified stand-off envelope and check ground offsets and fault voltages. A TVS has no operating supply rail; “24 V” does not mean it should be powered from 24 V. Continuous dissipation capability and thermal resistance for the TECH PUBLIC device remain unverified.
2. Pinout & Connections
The table below describes the verified Littelfuse application diagram. TECH PUBLIC C2937019’s manufacturer-controlled pinout remains unverified; confirm it before using this mapping for production.

Table


Pin NumberPin NameDescriptionBest Practice
1I/O 1 / CANHFirst protected bus line in the reference application Connect as a shunt branch to CANH, not in series. Keep branch short.
2I/O 2 / CANLSecond protected bus line in the reference application Connect as a shunt branch to CANL; use routing symmetry with CANH.
3GNDCommon transient return in the reference application Tie directly to the intended bus-side ground with a short, low-inductance return; do not leave floating.
For an isolated CAN interface, the return belongs to the isolated bus-side reference, not across the isolation barrier to MCU ground. Chassis grounding is a system EMC decision, not an automatic substitute for the documented GND connection.
3. Standard Application Circuit
Use one dual-line array at the external CAN connector. The verified Littelfuse wiring is pin 1 to CANH, pin 2 to CANL, and pin 3 to GND.

Text


CAN connector CANH ──────┬──────────────── Transceiver CANH
                        └── TVS pin 1
CAN connector CANL ──────┬──────────────── Transceiver CANL
                        └── TVS pin 2
Bus-side GND ─────────────── TVS pin 3
Integration procedure — engineering recommendations:
  1. Verify the purchased manufacturer and pinout first; the circuit above is not a verified TECH PUBLIC-specific wiring instruction.
  2. Connect the array in parallel with the bus. It diverts transient current to ground while leaving the communication path intact; it is not a series filter or a CAN transceiver.
  3. No TVS-specific pull-up, bias resistor, or supply-decoupling capacitor is required for this passive shunt topology. Follow the CAN transceiver’s own datasheet for its supply bypassing and logic-pin biasing.
  4. Retain the network’s required termination independently of the TVS. For a conventional high-speed CAN bus, place a 120 Ω termination across CANH/CANL at each physical end only, not at every node. A split termination or common-mode choke is optional system circuitry; its values and placement require the actual transceiver, cable and EMC requirements. Do not add arbitrary capacitors from CANH/CANL to ground to “help” the TVS.
  5. Check protection coordination: at the required surge current, TVS clamp voltage plus PCB parasitic overshoot must stay within the transceiver’s tolerable transient envelope. The Littelfuse reference can reach 50 V at 10 A; a device’s 24 V stand-off rating is not its protected-node voltage during a surge.
  6. Validate communication and EMC on the assembled interface, including negative transients, powered/unpowered conditions and bus common-mode offsets. No specific CAN-FD bitrate is guaranteed here; capacitance and network topology must be evaluated together.
4. PCB Layout & Routing Guidelines
These are general CAN-TVS engineering recommendations, not a verified TECH PUBLIC land-pattern specification. Nexperia’s primary-source CAN protection guidance corroborates close-to-connector placement, short protected-line connections, minimized loops, separation of protected/unprotected conductors, short return paths, and ground planes/vias (PESD2CAN24LT-Q, section 10); its citation-backed extraction was still pending at completion.
  • Place at the entry point: Locate the TVS next to the CAN connector, before long internal routing. Route connector → protection node → transceiver with minimal shunt stubs; keep unprotected connector traces away from protected logic and internal traces.
  • Prioritize the surge return: Make pin 3’s connection short and broad, with nearby ground vias when a plane is on another layer. Avoid a long ground neck or a return shared through sensitive circuitry. Prefer a solid connection for the transient path; if thermal relief is required for assembly, ensure the spokes do not become the electrical bottleneck.
  • Size copper for pulses, not average bus current: Avoid narrow neck-downs in line-to-TVS and TVS-to-ground paths. No universal trace width is specified: check copper thickness, pulse waveform, repetition and via capability for the actual surge requirement; a continuous-current calculation alone does not establish transient performance.
  • Preserve CANH/CANL symmetry: Keep the pair together over a continuous reference where practical, minimize stubs and unnecessary vias, and avoid a large difference in protection-branch length. Use the system’s transmission-line target rather than inventing a component-specific differential impedance or length-match tolerance.
  • Check the real footprint and bypassing: Compare pin numbering, pad dimensions and orientation with the selected manufacturer’s drawing and your JLCPCB-compatible land pattern. The TVS has no supply decoupling capacitor; place transceiver bypass capacitors at the transceiver supply pins per that device’s datasheet.
5. Common Pitfalls / Things to Watch Out For
  1. Treating a shared MPN as a shared rating. TECH PUBLIC C2937019 is listed at 250 W / 5.5 A while the attached Littelfuse document gives 500 W / 10 A for the 8/20 µs pulse. LCSC listing; Littelfuse limits: Do not transfer Littelfuse automotive qualification, pinout, capacitance or pulse guarantees to TECH PUBLIC. A 500 W pulse rating is also not permission for continuous 500 W dissipation or sustained battery-fault clamping.
  2. Confusing stand-off with clamping, or defeating the return path. The Littelfuse reference has a 24 V stand-off but up to 50 V clamping at 10 A. Check the transceiver’s limits and pulse tolerance; do not assume a 24 V TVS holds the bus at 24 V. A floating or inductive ground return can leave substantial transient voltage at the transceiver even when the TVS itself survives.
Two verified functional alternatives from other manufacturers relative to TECH PUBLIC are below. Neither is declared an unconditional drop-in for C2937019, whose exact manufacturer pinout and land pattern are unresolved. Always requalify the replacement’s clamp behavior, capacitance, surge margin, temperature range and automotive requirements.

Table


AlternativeVerified basisCompatibility classification
Littelfuse SM24CANB-02HTG — LCSC/JLCPCB C151237, not C2937019Exact ordering number; SOT23-3; pins 1/2 bus and pin 3 GND; 24 V stand-off; 10 A and 500 W at 8/20 µs. Functionally similar to TECH PUBLIC; pin/footprint compatibility with C2937019 unverified. The single exact-name Flux result is the mixed-source TECH PUBLIC entry, so it is not presented as a verified Littelfuse library replacement.
onsemi NUP2105LT1G in FluxDual bidirectional SOT-23 protector; pins 1/2 lines, pin 3 common ground. 24 V working voltage; 44 V maximum clamp at 8 A, 8/20 µs; 30 pF maximum at 0 V and 1 MHz. Pin-compatible with the verified Littelfuse reference; same nominal SOT-23 package class, final footprint overlay required. Functionally similar only to unverified TECH PUBLIC. Not a 10 A guaranteed replacement for the Littelfuse 10 A requirement.
For automotive designs, onsemi identifies the SZ-prefixed family for AEC-Q101/site-control requirements; do not silently substitute the ordinary NUP2105LT1G for an automotive-qualified ordering code (onsemi family page).
An additional Nexperia candidate was investigated but is not counted as verified here: the PESD2CAN24LT-Q pinout/rating citation lookup remained pending. No third fully verified replacement or unconditional TECH PUBLIC drop-in was established.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsExact TECH PUBLIC target: LCSC C2937019; JLCPCB C2937019 for assembly. A franchised authorization relationship for TECH PUBLIC was not verified. Littelfuse alternative: distinguish JLCPCB C151237 and Arrow’s Littelfuse listing; DigiKey/Mouser are sourcing channels to check for the Littelfuse version, not evidence that they supply TECH PUBLIC C2937019.
Packaging OptionsTECH PUBLIC listing: 3,000/full reel; exact tape geometry and supplied small-order format require confirmation from LCSC. Littelfuse: tape-and-reel, 8 mm tape / 7-inch reel, 3,000 pieces. Arrow lists cut strips for Littelfuse. onsemi NUP2105LT1G: 3,000/tape-and-reel.
Standard MOQTECH PUBLIC C2937019: LCSC displayed a 5-piece minimum and 3,000-piece full reel when researched. Littelfuse: Arrow displayed minimum 1 for cut strips; JLCPCB C151237 displayed minimum 1 for assembly stock and full reel 3,000. These are seller-specific snapshots, not universal manufacturer MOQs. Recheck at checkout.
Sourcing AdvicePut manufacturer + full MPN + distributor code on the BOM. Do not substitute C2937019 for C151237 based only on text matching. Request the TECH PUBLIC datasheet, pinout, pulse derating and qualification evidence before production. Use manufacturer-authorized/franchised channels where verified, and avoid untraceable marketplace stock. Confirm package and packaging suffixes rather than inferring them across manufacturers. Require traceable lot/reel labels and rerun protection tests after substitution.
Purchasing-status note: Research completed 6 October 2026. Stock, prices, MOQs and assembly classifications can change; no stock reservation or order was made. No schematic, symbol or footprint was changed by this guide.
Sources
  • Littelfuse manufacturer datasheet, SM24CANB Series: Direct PDF. Attached indexed document revised GD. 04/29/22. Used for clearly labeled Littelfuse reference ratings, pinout, geometry and ordering information—not TECH PUBLIC guarantees.
  • Littelfuse manufacturer product page: SM24CANB-02HTG. Used to distinguish manufacturer identity and intended CAN application. Web-page revision not provided.
  • LCSC primary distributor listing: TECH PUBLIC C2937019. Used for exact purchasing identity, explicitly distributor-listed ratings, MOQ and reel size. Its datasheet endpoint did not return an accessible PDF to the evidence reader; a manufacturer-controlled TECH PUBLIC PDF was not verified.
  • JLCPCB primary assembly listings: TECH PUBLIC C2937019 and Littelfuse C151237. Used for distinct purchasing codes, distributor-listed capacitance and assembly purchasing information.
  • onsemi manufacturer datasheet: NUP2105L/D PDF. Used for verified alternative pin connections, electrical characteristics and NUP2105LT1G ordering. Revision/date not independently established in this research; do not assume it from a mirror filename.
  • onsemi manufacturer product page: NUP2105 family. Used for exact orderable parts and SZ-family automotive qualification distinction.
  • Nexperia manufacturer datasheet: PESD2CAN24LT-Q PDF, v.1, 9 August 2024. Section 10 was read through the primary-source web reader for general layout guidance; immutable pinout/rating/layout evidence extraction remained pending, so this part is not certified as an equivalent in this guide.
  • Arrow primary distributor listing: Littelfuse SM24CANB-02HTG. Used for seller-specific cut-strip purchasing and one-piece minimum.
Unresolved release items: manufacturer-controlled TECH PUBLIC datasheet and document revision; exact TECH PUBLIC pinout/land pattern; guaranteed electrical limits and pulse derating; automotive qualification evidence; unconditional drop-in equivalence. Obtain these before treating this guide as a production qualification record.
  • 1. Quick Specifications

  • Exact purchasing target: TECH PUBLIC, LCSC C2937019

  • Attached datasheet reference: Littelfuse SM24CANB-02HTG only

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources