I’ll research the JST connector’s official specifications, Qwiic/STEMMA QT wiring conventions, and sourcing alternatives, then create a cited Application & Usage Guide in the project files.
I verified the connector ratings and interface pinout; the guide will distinguish JST’s connector limits from Qwiic’s 3.3 V requirements. I’ll also label the alternatives as functionally similar rather than claim unverified drop-in compatibility.
The JST SM04B-SRSS-TB(LF)(SN) is a four-contact, side-entry surface-mount wire-to-board header with 1.0 mm pitch, listed in JST’s SH connector family and sharing the SH/SR mating interface. A common application is a compact I²C sensor port carrying ground, power, SDA, and SCL in SparkFun Qwiic and Adafruit STEMMA QT systems (SparkFun Qwiic, Adafruit technical specifications).
1. Quick Specifications
Rating terminology: JST specifies connector service ratings, not an IC-style “Absolute Maximum Ratings” tab...
Created and checked the cited Application & Usage Guide in project files, covering all seven requested sections. It distinguishes connector ratings from Qwiic/STEMMA QT requirements and clearly flags unverified footprint details and replacement compatibility.
The JST SM04B-SRSS-TB(LF)(SN) is a four-contact, side-entry surface-mount wire-to-board header with 1.0 mm pitch, listed in JST’s SH connector family and sharing the SH/SR mating interface. A common application is a compact I²C sensor port carrying ground, power, SDA, and SCL in SparkFun Qwiic and Adafruit STEMMA QT systems (SparkFun Qwiic, Adafruit technical specifications).
1. Quick Specifications
Rating terminology: JST specifies connector service ratings, not an IC-style “Absolute Maximum Ratings” table. Do not relabel these as destructive absolute maxima; keep operation within the stated ratings and qualify the complete header/contact/wire/PCB assembly.
Table
Parameter
Verified value
Classification / design interpretation
Contacts and orientation
4 circuits; side-entry SMT header.
Mechanical configuration; right-angle cable entry
Contact pitch
1.0 mm.
Nominal mating pitch
Current rating
1.0 A AC/DC, specified with AWG #28 wire.
Connector service rating; not proof that a thin cable, PCB trace, or controller can supply 1 A
Voltage rating
50 V AC/DC.
Connector service rating; does not set the connected electronics’ voltage tolerance
Temperature range
−25°C to +85°C, including temperature rise caused by current.
Operating limit; +85°C ambient does not leave room for additional self-heating
Contact resistance
Initial: 20 mΩ maximum; after environmental tests: 40 mΩ maximum.
Qualification limits, not typical values
Insulation resistance
100 MΩ minimum.
Qualification specification
Dielectric withstand
500 VAC for one minute.
Test condition, not continuous working voltage
Header dimensions
JST table: A = 3.0 mm; B = 6.0 mm.
Interpret A/B using the drawing; not sufficient to generate a footprint
Contact finish / housing
Tin-plated copper-alloy contacts; PA housing, natural ivory.
Material information for the cited catalog version
Recommended application voltage for Qwiic interoperability, not a JST rating
STEMMA QT application supply
Adafruit’s general specification allows 3–5 V, with compatible regulation and logic support. Adafruit specifications
Verify each board; use 3.3 V for a mixed Qwiic/STEMMA QT chain
Unverified here: exact overall-height tolerance, complete numeric land pattern and physical pin-1 viewing orientation were not established from the retrieved drawing evidence. Use JST’s official model-specific drawing before releasing a footprint or enclosure; do not substitute an approximately stated height for a clearance requirement.
2. Pinout & Connections
The connector is electrically passive: JST does not assign I²C signal names. The table below is the Qwiic/STEMMA QT application assignment, supported by Adafruit’s numbered cable specification and SparkFun’s Qwiic convention. Physical left/right order depends on viewing direction; use JST’s Circuit No. 1 indication, not a mirrored cable photograph.
Table
Pin Number
Pin Name
Description
Best Practice
1
GND
Common power return; conventionally black wire
Tie to PCB GND and the host/device common ground; provide a low-impedance return
2
3V3 / V+
Peripheral supply; conventionally red wire
Use regulated 3.3 V for Qwiic; prevent two independent supplies from fighting through a cable
3
SDA
I²C bidirectional data; conventionally blue wire
Connect to host SDA and device SDA; provide a pull-up to the bus logic supply if one is not already fitted
4
SCL
I²C clock; conventionally yellow wire
Connect to host SCL and device SCL; provide a pull-up to the same bus logic supply if needed
Not a signal pin
Two solder-retention tabs
Mechanical reinforcement, separate from the four contacts; identified as solder tabs in JST’s header material description.
Solder both tabs to their dedicated lands; do not treat them as contacts 5/6 or assume they are a shield or mandatory GND connection
For a custom harness, JST lists SHR-04V-S as a four-circuit housing without handling protrusions. The listed SSH-003T-P0.2-H contact accepts AWG #32–#28 wire with 0.4–0.8 mm insulation outside diameter. Prefer a qualified precrimped cable if appropriate crimp tooling and inspection are unavailable; check end-to-end continuity before powering.
Wire a second daisy-chain connector in parallel, pin-for-pin, if required; it is the same bus, not a separate interface. SparkFun explicitly permits multiple Qwiic connectors and encourages a second connector on peripheral boards (Qwiic requirements).
Applicable passives and support circuitry:
Pull-ups: provide one effective pull-up on each of SDA and SCL. A practical starting option is 4.7 kΩ to 3.3 V, as used on SparkFun’s Qwiic GPIO board; this is an application example, not a resistor mandated by JST. Provide removable jumpers or DNP options where boards will be chained, and validate rise time and low-level sink current on the assembled bus (SparkFun reference implementation).
Do not stack pull-ups blindly: resistors on every attached board appear in parallel. SparkFun recommends disabling all but one pair where appropriate; evaluate the combined resistance rather than assuming every module requires its own populated pair (same reference).
Decoupling: the connector itself requires no capacitor. Place each sensor/IC’s required decoupling at its supply pins according to its own datasheet. Optional bulk capacitance at the port should be selected for load transients, cable impedance, and regulator stability; no universal 1 µF value is specified by JST.
Voltage translation: a 5 V-only host needs an appropriate bidirectional I²C level shifter before a 3.3 V Qwiic bus. Pull the connector-side SDA/SCL up to 3.3 V, not 5 V (SparkFun voltage requirements).
Protection, when needed: add a suitably rated current-limited power path and low-capacitance signal protection for accessible cables based on the product’s fault/ESD requirements. These are system design recommendations, not built-in connector features.
This is not a USB connector: USB CC pull-downs, USB shielding rules, and LED current-limiting calculations are not applicable. The connector’s voltage rating does not make an attached Qwiic sensor 5 V tolerant.
Use the side-entry land pattern: include four contact lands and both reinforcement lands, and cross-check pin numbering from symbol to footprint to cable. JST provides distinct top-entry and side-entry PCB/assembly drawings. Do not infer pad dimensions from pitch alone; the exact land dimensions remain unverified in this guide.
Reserve cable clearance: place the mating opening where the plug can be inserted and withdrawn without hitting components, the board edge, or the enclosure. Include the mated cable and bend path in mechanical checks; do not rely solely on the unmated header body.
Size power and ground together: calculate copper width and via capacity from actual chain current, copper thickness, allowed temperature rise, and voltage drop. Widen after the fine-pitch pad breakout. Do not assume a generic trace width supports the connector’s 1.0 A rating, particularly with the AWG #28 rating condition.
Route SDA/SCL as single-ended I²C signals: keep routes short, avoid unnecessary branches, maintain a ground return, and keep away from switching nodes. They are not a differential pair and need neither differential impedance targeting nor USB-style pair matching. Place IC decoupling at the IC, not merely beside the connector.
Balance solderability and heat sinking: retain both mechanical joints and follow the drawing/stencil guidance. Where GND or a reinforcement land is intentionally tied to a plane, choose thermal relief or solid connection to suit reflow and current requirements; narrow relief spokes must not become the power-return bottleneck. Inspect joints for bridging and incomplete wetting.
5. Common Pitfalls / Things to Watch Out For
Mirroring the footprint or assuming every four-pin JST cable has the Qwiic pinout. A polarized plug prevents reversed insertion into its own header; it does not guarantee another product’s net assignment. Verify Circuit No. 1, mark GND/V+, and continuity-test the cable and assembled PCB before applying power (SparkFun pinout, Adafruit numbered convention).
Confusing connector ratings with bus requirements. A connector rated 50 V is not permission to feed 5 V into a 3.3 V Qwiic device. Check regulator current, cable capacity, total downstream load, and all parallel pull-ups; excessive pull-up strength can prevent valid I²C low levels (SparkFun voltage rules, pull-up guidance).
6. Popular Alternatives & Equivalents
No cross-manufacturer drop-in replacement was verified. These are verified functionally similar connectors, not approved substitutions on an existing PCB. A supply-shortage substitution must independently establish signal numbering, land pattern, mechanical envelope, plug fit, materials, and assembly process.
Four-position, 1.25 mm pitch, right-angle through-hole header. Official product page
Functionally similar only; not footprint- or JST-SH-mating compatible
Redesign PCB for through-hole mounting and replace the cable/plug with a DF13 mating assembly. Exact ordering code was not found in the Flux library search
The Würth part’s equal pitch is not evidence of equal pad coordinates or guaranteed JST plug engagement. The Hirose option is a redesign path for a custom four-wire connection, not a way to retain direct Qwiic cable interoperability.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Direct listings verified at DigiKey, Future Electronics, and LCSC. Confirm regional franchise status and traceability through JST before placing production orders; listing alone does not prove authorization
Packaging Options
Manufacturer: embossed tape and reel. DigiKey additionally lists cut tape and Digi-Reel; these are distributor packaging services (DigiKey listing)
Standard MOQ
DigiKey: 1 unit cut tape; full-reel order starts at 3,000. DigiKey listing JST’s side-entry catalog quantity is 3,000 per reel. MOQ is distributor/order-specific, not a universal manufacturer minimum
JLCPCB / LCSC identifier
C160404 lists JST SM04B-SRSS-TB(LF)(SN), right-angle SMT, with 3,000-piece full reels. Check live assembly availability and procurement status before locking the BOM
Sourcing Advice
Order the complete SM04B-SRSS-TB(LF)(SN) code and retain supplier confirmation when a listing shortens it to SM04B-SRSS-TB. JST states the RoHS-compliant product displays (LF)(SN) on the label. Check side-entry versus top-entry, finish, and packaging. Avoid untraceable “JST-compatible” marketplace stock where dimensional, plating, or counterfeit risk is unacceptable; prefer manufacturer-confirmed franchised distributors
Do not confuse a factory reel quantity with a seller’s minimum order or a minimum order-value policy. Current prices, stock, and delivery dates are intentionally not frozen into this guide; confirm them at checkout. LCSC’s exact connector MOQ was not verified from the retrieved page.
Sources
Research checked October 6, 2026. Manufacturer catalog revision/date was not verified; no revision is inferred from a hosting timestamp.
JST, SH Connector official catalog:eSH.pdf. Specifications and pitch on page 1; header selection table on page 3 of the retrieved version. Revision/date not verified.
JST, SH Connector product and model drawings:official product page. Use the exact model-specific drawing for physical pin orientation and land pattern.
JST SH catalog copy used for the attached-part evidence:SparkFun-hosted eSH.pdf. Older two-page catalog format; electrical specification and header-label citations are provided inline. Do not mix its drawing dimensions with a newer revision without comparison.
SparkFun Electronics, Qwiic requirements and pinout:Qwiic. No revision/date verified.
Adafruit, STEMMA & STEMMA QT technical specifications:Technical Specs. Numbered cable assignment and voltage/logic requirements; no revision/date verified.
SparkFun Electronics, Qwiic GPIO reference design:Hardware Overview. 4.7 kΩ pull-up implementation and daisy-chain guidance; no revision/date verified.
Würth Elektronik, WR-WTB 1.00 mm male headers:Official product family. 665104131822 configuration and approved mating housing; no revision/date verified.
Hirose Electric, DF13-4P-1.25DS(25):Official product page. Pitch, contact count, orientation, and THT mounting; no revision/date verified.