SD-119 Footprint Audit


Thought for 25 mins 36 sec
Thought for 13 sec
1/2 Reconcile the current 15-pin part with the official drawing and correct symbol, terminal definitions, pad mappings, and land geometry.

Reconcile the current 15-pin part with the official drawing and correct symbol, terminal definitions, pad mappings, and land geometry.

Independently verify the corrected component and document any remaining limitations.

Thought for 35 sec
Thought for 9 sec
Awaiting 1 task
"SD-119 Footprint Audit" completed.
I’ve corrected the 15-pin symbol and pad mappings, component metadata, and pad geometry. I’m checking those changes independently; the footprint asset still displays the old silkscreen, and manufacturing drill and mask output remain unverified.
Thought for 4 mins 3 sec
Thought for 14 sec
Awaiting 1 task
"SD-119 Footprint Review" completed.
Thought for 7 mins 41 sec
Thought for 8 sec
Managing 1 task
Thought for 13 sec
Thought for 6 sec
Awaiting 1 task
"SD-119 Footprint Audit" completed.
I corrected the component metadata, 15-pin symbol definitions, pin names/functions, one-to-one pad mappings, and stored pad geometry; independent verification confirmed all 15 contacts and their mappings—see the updated audit.
The component is not fully corrected or release-ready: the active footprint asset still contains old geometry, shell-slot/drill/mask output remains unverified, and mechanical exclusions remain unresolved; pin numbers are present in metadata but not visible in the symbol.
The footprint activation issue requires Flux Support; after it is resolved, the next step is manufacturing-output verification before publication.

Footprint Datasheet Audit
Repair status — 2026-10-22
This replaces the earlier no-change audit. Revised authorization permits pin, symbol, mapping, metadata and footprint repairs; the old no-pin-change restriction is superseded. This repair batch is partially complete, not manufacturing-approved and not published.

Table


Assigned itemStatusEvidence / blocker
Current-state and source researchCompleted with citation limitationManufacturer PDF read manually; citation service remains evidence_pending.
Terminal identities, numbering and mappingCompletedFifteen existing terminal UIDs retained; symbol readback exposes numbers 1–15 exactly once. No terminals or nets were created or deleted in this repair pass.
Electrical types and symbol arrangementCompletedAll fifteen Passive; eleven Contacts left, four Shield contacts right; unique group orders; overlapping custom pin positions removed; parametric-v1 image shows separate contacts.
Part metadataCompletedDescription identifies standard SD push-pull socket, CD/WP, fifteen terminals; Part Type Connector, Connector Type Memory Connectors, Mount Through Hole, working Datasheet URL.
Direct source-pad geometry rulesCompleted at stored-rule/readback levelAll fifteen pads active; positions, copper dimensions, drilled-pad types and hole offsets read back. No !important overrides. Physical export still unverified.
Footprint source file synchronizationCompleted as asset storage; activation failedSame asset UID now stores revised 15-pad source. However, subsequent footprint asset.payload and Silk Shapes still show the old source. Stored source and resolved layout are inconsistent.
Silkscreen envelope correctionFailed to activateRevised source contains clearance-adjusted lines; current resolved silk remains the old geometry. Direct mutation of the generated silk UID was rejected as unknown.
Mechanical exclusion regionsFailed / blocked after focused investigationNo exclusions added: exact polygon boundaries, hatch-to-region association, and vertical clearance remain unresolved. See focused final review below. Silk is not a keepout.
Fresh component checksCompletedFive component-review categories Success, zero reported errors/warnings, reviewedAt 2026-10-22T16:47:05.544Z.
Manufacturing drill/mask verificationFailed / blockedPart project has no top-level board layout; native KiCad export rejected its footprint UID. Part layout image omits pads. Structured footprint parser omits drill/layer data despite explicit source clauses.
3D model dimensional reviewUnattemptedExisting STEP/model placement retained, not dimensionally revalidated.
PublicationUnattemptedNo publication or duplicate replacement part created.
Source and evidence limits
Manufacturer PDF used for manual review, SHA256 b596be554d835c5d5df4883010492e5df1d0ed608236d1baca25ec9455f47d8b. Physical page 2 contains the mechanical drawing; physical page 3 contains the recommended PCB top view, Details A/B and terminal table. Product page.
Manufacturer-derived interpretations below are unverified by the immutable citation service. The actual PDF drawings and raw extracted text were manually inspected; repeated batched query_datasheet requests remained evidence_pending and produced no validated citation handles. The pending questions concern contact diameters/X coordinates, Details A/B slot and copper geometry, mounting/outline datums, and the pin-definition table. They are not absent from the datasheet. Citation lookup is still pending.

commentFileId-b6f6a5683cc3012d4d0126c65299f2634f9d9d018ba5ee1cd956f418de9e822b

Details A/B image ·

commentFileId-83515868a191d3d06c254257f528549e17306bf251d587d2c15a22ecea3d0669

Land-pattern image ·

commentFileId-ad07d6efa0da7dc8c81d7c3672e194bb5e477a93762d90120e483d9dcfe31720

Mechanical centerlines ·

commentFileId-ccec509ed44ce509f6f9a2f069d19faec4f6292bcf2d779b989430d06d10fb7b

Mechanical datum.
Verified current project pin and pad readback
The following table reports stored project state, not citation-service-verified manufacturer claims. Coordinates are copper centers in millimeters, Flux X-right/Y-up. Terminal element UID is also its active pad UID.

Table


PinNameCopper XCopper YUID
1DAT2-9.7858.710fe000900-08cc-4c41-9978-603124f7743b
2DAT3-7.8358.71073f899e6-eb05-4e29-b4f1-a88d8bf378a8
3CMD-5.8858.71032512523-be74-47b6-9ff9-6f6f23ca25d4
4CD-3.9358.710e69b79eb-7bd2-485c-b929-27e9e0e715ea
5VSS1-1.9858.71085abb491-7e99-4295-a6e5-afebd9be17a2
6VDD-0.0358.71028c6821e-d261-46a1-9a1e-c69be6b64cde
7CLK1.9158.710bb83ed02-c1ab-4b08-979e-959228fc20cf
8VSS25.1908.71053df4385-ebec-47d7-bc97-2a29979dedc7
9DAT07.1408.710375590fb-bfdf-4836-93cf-0b5756df2085
10DAT19.0908.71097a1486f-bcef-4bda-a742-555d6d92ce1e
11W/P11.0408.710cc68941d-e6d8-48f8-b53d-12f785194e0c
12GND13.0654.7552d3d7d64-0658-4b54-afbe-4e5519463515
13GND13.065-8.3955b556825-c663-47dc-8c81-0843d8f48b66
14GND-13.065-8.3959f12bec8-dbc3-462f-a2a3-073ebbca2ae8
15GND-13.0654.755f6868748-fc55-4ed2-b57e-a6a657772f9b
Verified input rules:
  • Pins 1–11: circular copper 1.60 × 1.60 mm, STD plated through-hole, 1.00 × 1.00 mm drill, zero hole offset.
  • Pins 12–15: rectangle 1.15 × 2.55 mm with cornerRadius 0.575 mm, intended true capsule; STD, 0.55 × 1.30 mm slot. Pins 12/15 holePosition=(0,+0.325) mm; pins 13/14=(0,-0.325) mm; zero rotation.
  • All pads forceAnnularLayers=All and solderPasteMaskExpansion=-2 mm. This is intended paste suppression, not a verified manufacturing-output result. Solder-mask expansion was not explicitly changed.
  • Hole centers calculated from stored pad centers and offsets: upper pair Y=5.080 mm; lower pair Y=-8.720 mm; X=±13.065 mm. Column separation 26.130 mm and row separation 13.800 mm.
  • Project has 15 terminal components, 0 BOM items and 0 nets. No wiring changes.
Manual-source rationale — unverified citation status
These are manual interpretations of PDF pages 2–3, not validated immutable citations:
  • Use midpoint of the mounting-column span as X=0, not the separately offset card-slot centerline. Retain signal row Y=8.710 mm as the existing project datum.
  • Pin 6 is placed at X=-0.035 mm, consistent with the page-3 top-view leader and 1.950 mm pitch from pins 5–7; it replaces the imported +0.040 mm.
  • Upper mounting-hole Y=8.710−17.430+13.800=5.080 mm; lower Y=8.710−17.430=−8.720 mm.
  • Details A/B were interpreted as copper width 1.150 mm and longitudinal extents 1.600/0.950 mm about the slot center, giving 2.550 mm total length and 0.325 mm copper-center offset; slot 0.550 × 1.300 mm.
  • Contact copper interpreted as diameter 1.600 mm and drill diameter 1.000 mm.
  • The revised source silk uses nominal body envelope X=±13.240 mm, Y=9.040 to −10.370 mm. Its gaps and 0.250 mm stroke are engineering drawing-clearance choices, not manufacturer keepout definitions.
Footprint asset and unresolved activation
Existing asset UID 0d7cc683-b757-4ec1-a7f4-5e54b693053e retained. Current stored footprint source.
The source was edited from the original rather than replaced by an unrelated footprint. It has fifteen uniquely numbered pads instead of four repeated pad-12 records, corrected copper/drill definitions, and ten revised silkscreen segments. Native structured parsing confirms 15 unique numbers, contact coordinates/sizes and shell anchor coordinates/sizes. The KiCad source uses hole-anchor (at) coordinates plus copper offsets; Flux's direct node rules use copper centers plus hole offsets. Do not substitute one coordinate convention for the other.
Error — source activation inconsistency: get_assets confirms the new storage URL, but subsequent get_layout footprint asset.payload still contains the old 1.52 mm contact lands, repeated pad 12 and old silk, even though direct pad rules resolve to the corrected dimensions. The current resolved Silk Shapes payload still has X=±13.21 mm and the old segments. Therefore the source-file upload alone is not evidence that corrected silk is active. Escalation: refresh/rebind/recompile this same footprint asset through the supported part editor and read back asset.payload and silk before release; retain all terminal UIDs and direct pad rules.
Verification and release blockers
  • Completed: post-change symbol pins readback contains all fifteen Passive contacts with separate orders and groups; image shows eleven left contacts and four right shell contacts without overlap. Pad tree readback includes fifteen active pads and the explicit geometry listed above.
  • Completed: fresh component-review checks at 2026-10-22T16:47:05.544Z: Incomplete Project Info, Missing Properties, Missing Terminals, Missing Parametric Symbol Properties and Excluded Terminal all Success; zero reported errors/warnings.
  • Warning: requested board DRC categories did not return board checks in this part project. Mutation checks repeatedly returned NOT CHECKED. This is not a clean board DRC or manufacturing sign-off.
  • Error / release blocker: active silk/source payload is stale relative to stored asset, as described above.
  • Warning / release blocker: actual plated-slot locations, capsule outlines, mask openings and absence of paste need a placed-part board/export check. Native export failed because there is no top-level board layout. Structured library parser reports drill=none and layer=unknown despite explicit source drill/layer clauses; do not infer that drills were independently verified.
  • Warning / release blocker: exact no-component/body-height exclusion regions remain unimplemented. Apply source-derived exclusions using a supported mechanical keepout representation, not silk alone.
  • Info: KiCad 10.0.7-10.0.7~ubuntu24.04.1 serialized the edited source, but Python SWIG verification failed repeatedly. No successful independent KiCad round-trip, DRC, offset-semantics check or repaired-source-geometry.json is claimed.
  • Info: existing 3D model and placement were retained, not dimensionally checked. No new publication, duplicate part, or duplicate quality ticket.
This report separates verified stored edits from unverified manufacturer provenance, unresolved source activation, and unverified manufacturing output. The assigned repair batch does not establish completion of the overall part release.
Focused final review — independent-review follow-up
Only the three targeted omissions and final evidence record were investigated in this follow-up. No pin identities, mappings, geometry, assets, or publication state were changed. No replacement project was created; no speculative asset rebuild was attempted.

Table


Targeted itemFinal statusFresh evidence and exact blocker
Mechanical exclusionsFailed / blockedFresh zone/polygon tree inspection returns no matching nodes. Source-file OCR confirms separate legends for connector outline, body-height keepout, and no-component area, but does not associate each hatch with a fully dimensioned closed boundary. Missing resolved inputs: each region's complete X/Y vertices relative to mounting-hole/contact-row datum; hatch-to-region assignment; numeric vertical clearance and its board-surface reference for any height-limited region. Do not substitute overall body bounds for these distinct regions.
Visible symbol pin numbersFailed / blockedFresh symbol image still shows fifteen separate contacts with names/types but no visible pin-number labels. Fresh pin table has numbers 1–15 exactly once, all Passive, groups and orders unchanged. Property lookup rejects Show Pin Numbers, Pin Number Visibility and Symbol Pin Number as unknown. Canonical property list and three differently phrased help searches expose no supported visibility control. This control may be unavailable; no arbitrary property, pin renaming or custom-symbol workaround was applied.
Unsupported continuous voltage ratingCompleted, no removal neededFresh full project metadata contains no Operating Voltage, Voltage Rating or Voltage property. Fresh fifteen-pin table likewise contains no voltage-rating property. No continuous rating was assigned from the 500-VAC dielectric-test figure mentioned in the review brief. A dielectric withstand test must not be represented as a continuous operating rating.
Audit and blockersCompletedThis amendment records targeted readbacks and distinguishes the platform activation error from physical-manufacturing uncertainties.
Mechanical source and supported-rule limits
The targeted query against the saved manufacturer PDF remains evidence_pending: immutable extraction/indexing is still running, and the query returned no answer. The separate file-search OCR result is unverified and reads “THIS AREA CORRESPONDS TO THE HEIGHT OF THE CONN.BODY,PLEASE KEEP OUT” and “NO COMPONENT AREA”; it does not establish the missing region vertices or height value. This is unresolved evidence, not a claim that the manufacturer omitted these features. A legible, dimensioned region interpretation tied to the datum is required before adding exact exclusions.
Rule-definition readback confirms Keep Out (keepOut) is a distance outside object bounds and Zone Shape (zoneShape) supports custom SVG boundaries. The queried Component Height and Zone Type rules are unknown. A general spacing rule alone does not prove a supported height-limited mechanical-volume exclusion. Both exact source geometry and suitable part-source semantics must be established; no copper-routing prohibition was invented as a substitute for a component-only restriction.
Platform and manufacturing blockers retained without retry
  • Error — platform activation blocker: independent review confirms resolved asset.payload still contains 1.52-mm contact lands and four records numbered 12. By contrast, the stored replacement source has unique pad numbers 1–15 and 1.60-mm contact lands, and active direct source-pad rules carry the corrected mapping/dimensions listed above. Resolved silk remains old rather than the revised source's ten clearance-adjusted segments. Upload success is not activation success. Stop automated activation retries; platform-side diagnosis is required.
  • Warning — shell geometry semantics unverified: stored cornerRadius=0.575mm on 1.15 × 2.55-mm shell lands expresses the intended capsule, but actual rendered/exported rounding is not proven. The ±0.325-mm Flux hole offsets and KiCad hole-anchor/copper-offset conventions have not been independently verified through manufacturing output.
  • Warning — manufacturing output unverified: no verified exported plated circular drills or plated slots; no verified solder-mask apertures; no verified absence of paste. The −2-mm paste expansion is an input rule only. Native export lacks a top-level board layout, and the library parser omits drill/layer semantics. These blockers remain; no export success or clean manufacturing DRC is claimed.
  • Info: the earlier five successful component-review categories are not newly rerun board/manufacturing checks and do not resolve the above blockers. Existing 3D validation and publication remain unattempted.
The focused batch is complete as an investigation and record update, but mechanical exclusions and visible pin numbers were not implemented. Overall release remains blocked.
  • Repair status — 2026-10-22

  • Source and evidence limits

  • Verified current project pin and pad readback

  • Manual-source rationale — unverified citation status

  • Footprint asset and unresolved activation

  • Verification and release blockers

  • Focused final review — independent-review follow-up

  • Mechanical source and supported-rule limits

  • Platform and manufacturing blockers retained without retry