Fuse Datasheet Research


I’ll research the manufacturer’s specifications and verified alternatives, then write a cited application and usage guide in the project files.
Distributor listings show discrepancies with the existing description, including a 1.8 A trip current and 50 A maximum fault current. Datasheet verification is failing, so I’ll clearly flag unresolved claims and avoid calling any alternative a verified drop-in replacement.
Created a project doc

0603L100SLYR Application and Usage Guide

View Document

0603L100SLYR Application and Usage Guide
The Littelfuse 0603L100SLYR is a two-terminal, surface-mount polymeric positive-temperature-coefficient (PPTC) resettable fuse in the Low Rho/LoRho family, intended for series overcurrent protection of low-voltage power rails; manufacturer-datasheet verification remains unresolved, although the device identity is corroborated by DigiKey’s product listing. Its common applications include compact USB-powered peripherals and battery-powered electronics where a recoverable current-limiting response is preferable to replacing a one-time fuse, as described in the [Littelfuse Low Rho datasheet](https://www.littelfuse.com/assetdocs/low-rho-datasheet-update?assetguid=b7...
Created the 0603L100SLYR Application and Usage Guide in the project files, covering all seven requested sections with source links.
It remains a research draft: manufacturer-datasheet verification failed, so unresolved ratings, footprint details, and replacement compatibility are explicitly flagged. Those gaps need resolution before publication or production use.

0603L100SLYR Application and Usage Guide
The Littelfuse 0603L100SLYR is a two-terminal, surface-mount polymeric positive-temperature-coefficient (PPTC) resettable fuse in the Low Rho/LoRho family, intended for series overcurrent protection of low-voltage power rails; manufacturer-datasheet verification remains unresolved, although the device identity is corroborated by DigiKey’s product listing. Its common applications include compact USB-powered peripherals and battery-powered electronics where a recoverable current-limiting response is preferable to replacing a one-time fuse, as described in the Littelfuse Low Rho datasheet; application-specific qualification is still required.
Verification status — research draft, not a release-qualified reference. Manufacturer PDFs were located and their web-extracted content reviewed, but citation-backed datasheet verification failed or remained pending. Every numerical manufacturer claim below is explicitly marked unverified against the datasheet; distributor corroboration is identified separately. Conflicting or ambiguous extracted geometry and alternative-part trip-time values have been omitted rather than guessed. This guide does not modify the part’s symbol, footprint, or existing description.
1. Quick Specifications
Source for distributor-corroborated values: DigiKey 0603L100SLYR. Primary reference awaiting validated extraction: Littelfuse Low Rho datasheet.

Table


ParameterValue and conditionsRating category / verification
Maximum voltage, Vmax6 VMaximum device rating, not a recommended rail voltage; distributor-corroborated, unverified against datasheet
Maximum fault current, Imax50 AFault withstand rating at rated voltage, not continuous load current; distributor-corroborated, unverified against datasheet
Hold current, Ihold1.00 A; web extraction indicates 20 °C still-air referenceNon-trip current under specified conditions, not a guaranteed all-temperature load rating; value distributor-corroborated, reference conditions unverified against datasheet
Trip current, Itrip1.80 A at reference conditionsTrip characteristic, not a precision current-limit setpoint; distributor-corroborated, unverified against datasheet
Maximum time to trip0.30 s at 8.00 A according to manufacturer web extractionConditional test specification, not 0.30 s at every overload; 0.30 s distributor-corroborated, test current and conditions unverified against datasheet
Initial minimum resistance, Rmin0.040 ΩMinimum, not typical or maximum; distributor-corroborated, unverified against datasheet
Post-trip resistance, R1max0.120 ΩDistributor identifies post-trip maximum; recovery interval and precise test conditions remain unverified against datasheet
Typical tripped-state dissipation0.6 W according to manufacturer web extractionNot an ordinary resistor’s continuous power rating; unverified against datasheet
Operating temperature−40 °C to +85 °CEnvironmental range, not assurance of 1 A hold throughout; distributor-corroborated, unverified against datasheet
Package0603 / 1608 metric, concave, two terminalsNominal 1.60 × 0.80 mm body; distributor-corroborated, unverified against datasheet
Maximum thickness0.75 mmDistributor-corroborated, unverified against datasheet
Pin pitch / land patternNo validated pad-center pitch available in this researchUnverified; do not substitute body length for terminal pitch
Practical operating choiceUse on a low-voltage rail whose worst-case voltage remains within Vmax, with load below the temperature-rerated hold currentEngineering recommendation; no universal safe load current or margin can be assigned without the actual board environment
The current project description’s approximately 2 A trip current and 40 A maximum fault current conflict with the 1.8 A and 50 A distributor values. Resolve against the exact manufacturer revision before updating production records. Exact temperature-rerating values are intentionally not reproduced because retrieved versions disagreed.
2. Pinout & Connections
The package has two passive terminals and no enable, ground, or logic pin. The following numbering is a schematic convention, not a verified manufacturer pin assignment; the nonpolar series connection should be checked against the actual Flux symbol and footprint before use.

Table


Pin NumberPin NameDescriptionBest Practice
1, conventionTerminal A / source sideFirst end of the PPTC current pathConnect to incoming power; place close to the power entry to minimize unprotected copper
2, conventionTerminal B / protected sideSecond end of the PPTC current pathConnect to the protected load or regulator input; avoid any alternate path that bypasses the fuse
No pull-up, pull-down, or dedicated GND connection is required for a two-terminal series fuse. Do not wire this device across power and ground.
3. Standard Application Circuit
Typical low-voltage input protection topology — engineering recommendation:

Text


Incoming positive supply ── F1: 0603L100SLYR ── protected rail ── regulator/load
Supply return            ──────────────────────────────────── load GND
  • Put F1 in series with the positive supply, upstream of the circuitry whose fault current it should limit. For a nominal 5 V or 3.3 V system, check source tolerance, transients, and the voltage that can appear across F1 after a downstream short; nominal voltage alone is insufficient.
  • No dedicated passive support components are required by this topology. Select regulator input capacitors and load decoupling from the downstream devices’ datasheets, not from the fuse package. Do not invent a universal 1 µF capacitor requirement.
  • Include downstream capacitance, startup surges, repetitive load pulses, and hot ambient conditions in nuisance-trip testing. A thermal PPTC is not a precise or instantaneous electronic current limiter.
  • Estimate voltage loss using ΔV = I × R and heating using P = I² × R. For illustration only, if a recovered device measures 0.120 Ω at 1 A, the calculated loss is 0.120 V and 0.120 W. This is a conditional calculation, not a guaranteed hot operating value or a validated maximum for all conditions.
  • A tripped PPTC remains a finite-resistance path rather than an isolation switch. Remove the fault and reduce/remove power long enough for cooling before attempting restart; exact reset timing and residual current are unverified for this part.
  • In USB equipment, use F1 on VBUS, not D+/D− or CC. It does not negotiate current, establish USB compliance, or provide reverse-current, ESD, or overvoltage protection. Do not use this 6 V-rated part on a port that can negotiate above its rating; the 6 V value remains unverified against the datasheet.
4. PCB Layout & Routing Guidelines
The following are engineering recommendations, not claimed manufacturer layout prescriptions:
  • Use the exact PPTC land pattern. The Littelfuse web extraction identifies a recommended drawing, but its dimension mapping was ambiguous; pad size, pad gap, and center pitch remain unverified. Match the manufacturer drawing before fabrication rather than assuming a generic 0603 resistor footprint is interchangeable.
  • Minimize unprotected routing. Place the fuse near the input connector, keep the source-side path short, and keep fault-prone downstream routing on the protected side.
  • Size copper for both operating and pre-trip fault conditions. Use copper thickness, layer position, acceptable temperature rise, and the measured fault duration to select trace widths and vias; no universal width is justified here. Include pad neckdowns and thermal-relief spokes in the weakest-path check.
  • Treat copper as part of the thermal design. Copper area, thermal relief, nearby heat sources, airflow, and enclosure temperature can alter trip behavior. Avoid arbitrary heatsinking or isolation changes after qualification; test with the intended copper and assembly.
  • Keep downstream decoupling at its load. Route fuse power paths without disrupting signal return planes. Differential-pair length matching and CC/shield connections are not fuse requirements; preserve those interfaces independently.
5. Common Pitfalls / Things to Watch Out For
  1. Treating “1 A hold” as an all-temperature or precision limit. The cited nominal value is distributor-corroborated but unverified against the datasheet; hold and trip behavior depend on temperature and thermal surroundings. Verify normal-load margin in the hottest intended enclosure, then test startup and repeated transient loads.
  2. Treating a PPTC as a fast open-circuit fuse or universal safety barrier. It heats before tripping, continues passing residual current while tripped, and does not clamp voltage. Coordinate the source, wiring, sensitive semiconductors, and any secondary protection; do not mistake the reported 50 A fault rating for permissible continuous current.
No unconditional drop-in replacement was verified. Two real Bourns alternatives were identified from manufacturer sources; their numerical specifications remain unverified against citation-backed datasheet extraction, and compatibility labels below are deliberately conservative. Exact Flux library searches found no usable match for either ordering code, so the links point to manufacturer datasheets rather than implying library availability.

Table


CandidateReported manufacturer valuesCompatibility and qualification action
Bourns MF-FSML100/8-20603 low-ohmic PPTC; 1.00 A hold, 2.00 A trip at 23 °C; 8 V maximum; 50 A fault rating; Rmin 0.040 Ω, R1max 0.220 Ω — all unverified against datasheetFunctionally similar; same nonpolar two-terminal topology. Same nominal package class, but footprint compatibility is not verified. Its reported resistance and trip threshold differ; trip-time extraction was inconsistent and is omitted. Check pad overlap, height, hot hold current, trip curves, and voltage drop before substitution.
Bourns MF-PSMF110X-20805 PPTC; 1.10 A hold, 2.20 A trip at 23 °C; 6 V maximum; 40 A fault rating; Rmin 0.060 Ω, R1max 0.210 Ω — all unverified against datasheetFunctionally similar only; not footprint-compatible with the original 0603 package. Requires a PCB footprint change and protection requalification. Same two-terminal series topology does not make it electrically equivalent.
These are from a manufacturer other than Littelfuse, but are not approved alternate BOM entries. Package names and matching hold current alone do not establish interchangeability.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsExact-part listing verified at DigiKey; JLCPCB/LCSC part C207017 was also found. Mouser listing appears in search results, but current order terms and authorization were not independently confirmed. Check manufacturer-authorized channels for the destination region.
Packaging OptionsDigiKey lists Tape & Reel, Cut Tape, and Digi-Reel. Manufacturer web extraction reports ordering code 0603L100SLYR, with Y = 4,000-piece quantity and R = tape and reel; suffix interpretation is unverified against datasheet.
Standard MOQDigiKey’s directly read listing starts Cut Tape at 1 unit and lists a 4,000-piece manufacturer-standard reel. This is distributor-specific, not a universal MOQ. Verify other sellers’ order multiples and assembly-feed requirements at purchase.
Sourcing AdvicePurchase traceable stock from franchised/authorized distributors; verify authorization rather than assuming any marketplace listing is authorized. Match the entire 0603L100SLYR ordering code, packaging, manufacturer identity, and reel label. For JLCPCB assembly, confirm current C207017 stock and sourcing conditions. Avoid broker or marketplace stock with unverifiable lot provenance.
Stock, pricing, lead time, and MOQ can change; this guide does not certify live inventory or guarantee availability.
Sources
  • Primary — Littelfuse: Low Rho Series PolySwitch Resettable PPTC datasheet. Web extraction reports Rev. GD, 03/06/25; revision/date and numerical content remain unverified by citation-backed datasheet lookup. Do not confuse this SL low-resistance family with a generic 0603L series document.
  • Primary — Bourns: MF-FSML/X low-ohmic PPTC datasheet. Web extraction reports Rev. C, 08/26; revision/date and numerical content remain unverified, with citation-backed extraction still pending.
  • Primary — Bourns: MF-PSMF PPTC datasheet. Web extraction reports Rev. Q, 09/26; revision/date and numerical content remain unverified, with citation-backed extraction still pending.
  • Distributor primary listing: DigiKey 0603L100SLYR. Used for distributor corroboration and directly read packaging/order quantities, not as a substitute for manufacturer rating conditions.
  • Assembly/distributor listing: JLCPCB C207017. Used to identify the assembly catalog code; live stock not certified.
Research date: October 6, 2026. Before publication or production use, resolve the manufacturer evidence gaps, compare the exact footprint drawing, and qualify alternatives on the intended PCB.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources