USBLC6-2P6 Guide


I’ll turn the attached brief into a cited USBLC6-2P6 application guide, verify the pinout/layout guidance and alternatives, then save it as a project file.
Created a project doc

USBLC6-2P6 Application and Usage Guide

View Document

USBLC6-2P6 Application and Usage Guide
The USBLC6-2P6 is a two-channel, rail-to-rail TVS/ESD protection array for high-speed interfaces, supplied in a compact SOT-666 package. Its most common use is protecting USB 2.0 D+/D− and VBUS at the connector while preserving signal integrity through low and well-matched line capacitance.
1. Quick Specifications
Important: the 1 A and 5 A values above are clamping-voltage test points, not a stated repetitive current capability. Treat ESD and 8/20 µs surge ratings as transient limits, not continuous-current ratings.
2. Pinout & Connections
Top-view pin assignment: pins 1 and 6 form I/O1, pins 3 and 4 form I/O2, pin 2 is GND, and pin 5 is VBUS.[^flux:cite:s...
Created the cited USBLC6-2P6 Application and Usage Guide. It covers specifications, pin connections, USB 2.0 integration, PCB layout, common errors, verified alternatives, and sourcing guidance.

USBLC6-2P6 Application and Usage Guide
The USBLC6-2P6 is a two-channel, rail-to-rail TVS/ESD protection array for high-speed interfaces, supplied in a compact SOT-666 package. Its most common use is protecting USB 2.0 D+/D− and VBUS at the connector while preserving signal integrity through low and well-matched line capacitance.
1. Quick Specifications

Table


ParameterClassificationValueConditions / Notes
Reverse working voltage, VRMOperating characteristic5.25 VLeakage specified at this voltage.
Leakage current, IRMOperating characteristic10 nA typ.; 150 nA max.VRM = 5.25 V.
Breakdown voltage, VBROperating characteristic6 V min.VBUS-to-GND, IR = 1 mA.
I/O-to-GND capacitanceOperating characteristic2.5 pF typ.; 3.5 pF max.VR = 1.65 V.
I/O-to-I/O capacitanceOperating characteristic1.2 pF typ.; 1.7 pF max.VR = 1.65 V.
Clamping voltage, VCLSurge test characteristic12 V max.IPP = 1 A, 8/20 µs.
Clamping voltage, VCLSurge test characteristic17 V max.IPP = 5 A, 8/20 µs.
IEC 61000-4-2 immunityGuaranteed device-level rating15 kV air; 8 kV contactLevel 4 compliance.
Operating junction temperatureAbsolute rating−40 to +150 °CNo separate recommended ambient-temperature range is specified.
Storage temperatureAbsolute rating−55 to +150 °CAbsolute maximum rating.
PackageMechanicalSOT-666, 6 pins0.50 mm lead pitch.
Important: the 1 A and 5 A values above are clamping-voltage test points, not a stated repetitive current capability. Treat ESD and 8/20 µs surge ratings as transient limits, not continuous-current ratings.
2. Pinout & Connections
Top-view pin assignment: pins 1 and 6 form I/O1, pins 3 and 4 form I/O2, pin 2 is GND, and pin 5 is VBUS.

Table


Pin NumberPin NameDescriptionBest Practice
1I/O1One side of protected data path 1Route one side of D+ or D− through this pin; pair with pin 6 as a straight flow-through path.
2GNDESD surge-return referenceConnect directly to a solid ground plane with the shortest practical path; avoid a long neck or shared return trace.
3I/O2One side of protected data path 2Route one side of the other USB data line; pair with pin 4.
4I/O2Opposite side of protected data path 2Continue directly to the USB transceiver while maintaining differential-pair geometry.
5VBUSPositive clamp reference and VBUS protection connectionConnect to the USB 5 V VBUS net with a short trace; place a 100 nF ceramic capacitor from VBUS to GND close to the device when following the datasheet layout example.
6I/O1Opposite side of protected data path 1Continue directly to the USB transceiver; do not create a branch stub.
The I/O pairs are electrically symmetric; “connector side” and “system side” may be assigned to opposite ends if that produces a cleaner straight-through layout.
3. Standard Application Circuit
Place the USBLC6-2P6 immediately behind the USB connector. Route D+ through pins 1↔6 and D− through pins 3↔4, connect pin 2 to the ground plane, and connect pin 5 to the protected 5 V VBUS rail. ST’s USB 2.0 application and PCB-layout examples use separate D+ input/output and D− input/output paths and show a 100 nF capacitor between VBUS and GND.
Required / recommended external parts:
  • 100 nF ceramic capacitor, VBUS-to-GND: place beside pins 5 and 2 with a compact loop, particularly if the VBUS or ground connection cannot be made extremely short.
  • No data-line pull-ups, pull-downs, or series resistors are inherently required by this protection IC. Any USB termination or role-identification resistors belong to the USB transceiver/connector implementation, not to the USBLC6-2P6 itself.
  • USB-C CC resistors are unrelated to this part. If used in a USB-C product, provide the correct Rp/Rd circuitry separately; the USBLC6-2P6 protects only the two routed I/O channels and the connected VBUS reference.
4. PCB Layout & Routing Guidelines
  • Put the device as close as possible to the USB connector or other disturbance entry point.
  • Keep the data-line-to-I/O, VBUS-to-pin-5, and ground-plane-to-pin-2 paths extremely short; parasitic inductance directly increases residual clamp voltage.
  • Route D+ and D− straight through the package without stubs, while preserving the differential pair’s spacing, reference plane, symmetry, and impedance rules.
  • Use a solid, low-inductance ground connection. Do not use a narrow thermal-relief-style spoke as the only ESD return if a direct plane connection or nearby ground via is available.
  • The data pins do not carry USB power current. Size the VBUS power path for the connector/load elsewhere; keep the short pin-5 branch optimized for low inductance rather than treating it as the main VBUS feed.
5. Common Pitfalls / Things to Watch Out For
  1. Placing the TVS near the MCU instead of the connector. This leaves a long unprotected trace that can radiate or couple ESD energy into the board before the surge reaches the clamp.
  2. Using long or shared GND/VBUS connections. The device may meet its datasheet rating while the system still experiences excessive residual voltage because PCB trace inductance adds to the clamp voltage.
Also verify the package orientation carefully: the top-view pinout places GND on pin 2 and VBUS on pin 5; swapping these defeats the intended rail-to-rail protection network.

Table


AlternativeManufacturerCompatibilityEngineering Notes
RClamp0502A.TCTSemtechPin-compatible and footprint-compatible SOT-666/SC-89 candidateSame flow-through pin assignment: 1/6 and 3/4 are I/O pairs, pin 2 GND, pin 5 VCC. Lower capacitance, but its surge/clamping and leakage specifications differ; requalify ESD margin before substitution.
PRTR5V0U2FNexperiaPin-function compatible; not footprint-compatibleUses the same logical pin order in a smaller leadless SOT886/XSON6 package. Requires a PCB footprint change and assembly-process review; suitable as a functional redesign alternative for USB 2.0.
Do not approve a substitute solely because it is sold under a similar “USBLC6-2P6” name. Verify manufacturer, package drawing, pinout, capacitance, working voltage, clamp voltage, IEC rating, and surge waveform capability from that manufacturer’s current datasheet.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsST Online Store, Mouser, LCSC — C15999, plus DigiKey/Arrow/Future subject to regional stock.
Packaging OptionsManufacturer ordering information specifies tape and reel; franchised distributors may offer cut tape or custom reel services.
Standard MOQFull manufacturer reel base quantity: 3,000 pieces. Distributor cut-tape MOQ is commonly 1 piece, while LCSC may apply a small sales multiple.
Sourcing AdvicePrefer ST or franchised distributors. Match the exact USBLC6-2P6 order code, SOT-666 package, and reel/cut-tape option. Avoid assuming that same-named third-party parts are electrically or mechanically identical; counterfeit and remarking risk is materially higher on non-authorized marketplaces.
Sources
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources