I verified two important distinctions: the SC-70-6 version has a 1.2 A absolute-maximum continuous-current rating, and its reverse blocking is described for the disabled state. I’ll highlight both in the guide and clearly label the alternatives as requiring a PCB redesign.
The Vishay Siliconix SiP32431DR3 is an active-high, slew-rate-controlled high-side P-channel MOSFET load switch for selectively connecting a low-voltage supply to a load; the DR version uses the six-lead SC-70 package. Its common application is power-gating sensors and other battery-powered subsystems to reduce standby consumption, with reverse-current isolation when disabled and the output exceeds the input.
Scope: SiP32431DR3, ordered as SiP32431DR3-T1GE3. This guide covers its pinout, application circuit, PCB layout, substitutes, and sourcing—not the differently packaged DNP version. Use...
Created and checked the SiP32431DR3 Application and Usage Guide in the project files, covering all seven requested sections with datasheet citations and source links. It includes practical wiring and layout guidance, two functionally similar alternatives, and explicitly flags unverified drop-in compatibility and cut-tape purchasing details.
The Vishay Siliconix SiP32431DR3 is an active-high, slew-rate-controlled high-side P-channel MOSFET load switch for selectively connecting a low-voltage supply to a load; the DR version uses the six-lead SC-70 package. Its common application is power-gating sensors and other battery-powered subsystems to reduce standby consumption, with reverse-current isolation when disabled and the output exceeds the input.
Scope: SiP32431DR3, ordered as SiP32431DR3-T1GE3. This guide covers its pinout, application circuit, PCB layout, substitutes, and sourcing—not the differently packaged DNP version. Use the manufacturer datasheet alongside this guide. Research checked October 6, 2026; purchasing information is not a stock reservation.
1. Quick Specifications
Absolute maximum ratings are stress limits, not recommended design targets. Keep operating voltages, load current, transient energy, and temperature below their applicable limits with margin.
Table
Parameter
Recommended operation / typical characteristic
Absolute maximum / stress limit
Conditions and integration notes
Input voltage, VIN
1.5–5.5 V
−0.3 to +6 V
Include source tolerance, startup overshoot, and hot-plug ringing.
OUT and ON/OFF voltage
OUT follows IN minus switch drop when on; ON/OFF is the enable input.
Each: −0.3 to +6 V
The +6 V stress limit does not establish recommended operation above 5.5 V.
Continuous switch current, SC-70-6
Set the usable current from thermal dissipation and worst-case on-resistance.
1.2 A
Do not apply the family's 1.4 A TDFN rating to this SC-70-6 device.
Pulsed switch current
Not a continuous operating rating
3 A at VIN ≥ 2.5 V; 1.6 A at VIN VIN. Do not assume ideal-diode behavior or guaranteed reverse blocking while enabled.
This is a load switch, not a voltage regulator. LED series-resistor calculations, USB CC resistors, and differential-pair termination are not applicable to the component itself.
4. PCB Layout & Routing Guidelines
The following are practical board-design recommendations unless explicitly cited as manufacturer requirements:
Minimize the bypass loop: Place CIN beside IN pin 4 with a short, direct GND return; place COUT beside OUT pin 1 and keep its return compact. Vishay explicitly calls for CIN close to IN.
Size the power path, not just the pad neck: Use short, wide traces or copper pours for IN and OUT. Calculate width from copper thickness, layer, trace length, acceptable temperature rise, and voltage-drop budget; there is no universally valid trace width for the 1.2 A stress limit. Keep narrow SC-70 pad escapes short and size any vias for the load and inrush current.
Check dissipation before using the headline current: Estimate conduction loss as ILOAD² × RDS(on), using the maximum resistance applicable to supply and temperature. For illustration, 1 A and the 230 mΩ maximum at 5 V, 25 °C produce 230 mW—already near the 250 mW SC-70-6 dissipation rating. These operands are datasheet values; the loss is a derived example, not proof that 1 A is safe over temperature.
Use appropriate copper connections and thermal relief: Solder both GND pins and avoid long thin thermal spokes on current-carrying IN/OUT pads. If reliefs are used, check their electrical and thermal capacity while retaining an assembly-compatible pad pattern. The SC-70-6 thermal resistance is 220 °C/W; do not borrow the TDFN4 exposed-power-pad instructions or its 170 °C/W value.
Keep control clean and verify the package: Route ON/OFF away from noisy power transitions and keep its return referenced to GND. Use the 0.65 mm-pitch six-lead SC-70 outline, not a SOT-23-6 footprint merely because both have six pins. The device has no differential signal pair; impedance-controlled pair routing is not required for its pins.
5. Common Pitfalls / Things to Watch Out For
Treating reverse blocking as always active. The manufacturer describes reverse isolation with the switch disabled and OUT above IN. If a separately powered output can exceed the input while ON/OFF is high, do not rely on this part as an always-on reverse-current protector; select and validate an appropriate power-path device instead.
Using family headlines as a complete operating specification. The SC-70-6 current stress limit is 1.2 A, not the TDFN4 family's 1.4 A; package dissipation and resistance further constrain usable current. Likewise, 10 pA is a typical 3.3 V quiescent value, not a guaranteed total standby budget; include specified maximum current, external control resistors, and system leakage.
6. Popular Alternatives & Equivalents
No cross-manufacturer drop-in replacement was verified in this research. The two documented alternatives below are from Texas Instruments and are functionally similar only: neither is footprint-compatible with SC-70-6, and neither should be substituted on the existing board without schematic, layout, and power-budget review. Inclusion is a technically verified migration option, not a sales-volume ranking.
Active-high load switch; 1–5.5 V input, 2 A maximum continuous current; 6-pin SOT-23 DBV package.
Functionally similar only; not SC-70 footprint-compatible; not a verified pin-compatible replacement.
IQ is 0.5 µA typical, 1.0 µA maximum through +85 °C with output open. Rework the footprint and review timing/discharge connections. Its enabled reverse-current blocking has a −0.5 A typical, −1 A maximum activation threshold; this is not zero-current ideal isolation.
Active-high, no quick-output-discharge variant; 1–5.5 V input, 2 A maximum continuous current; 4-pin YFP DSBGA.
Functionally similar only; different pin count and footprint.
Requires a new fine-pitch assembly footprint; slow turn-on variant. IQ is 0.5 µA typical and 1.0 µA maximum with output open through +85 °C. Reverse blocking while enabled trips at −500 mA typical.
Both exact MPNs were found in the Flux library. Library presence alone does not verify footprint correctness or current purchasing availability; compare any chosen library asset with its manufacturer's pin and package drawings.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Exact-part listings were verified at TTI and Future Electronics. A Mouser listing surfaced, but direct page access was denied; its present stock and MOQ are unverified.
Assembly-oriented sourcing
JLCPCB lists SiP32431DR3-T1GE3 as C141606, under SOT-363-6. Confirm actual assembly availability and the manufacturer SC-70-6 geometry before committing a BOM. A catalog label is not a footprint validation.
Packaging Options
Reel packaging is confirmed by the TTI and Future listings. Cut tape and distributor re-reeling may be offered, but their current exact-part availability was not verified from an accessible primary distributor page.
Standard MOQ
TTI confirms a 3,000-unit reel minimum and order multiples of 3,000 on its exact-part page. A 1-unit cut-tape MOQ is unverified; obtain a distributor quote rather than assuming it.
Ordering Code
Use SiP32431DR3-T1GE3, not only the abbreviated project/family name. The manufacturer identifies it as the replacement for SiP32431DR3-T1-E3. DR denotes the SC-70 option in the ordering table; DNP is the differently packaged TDFN alternative, and SiP32432 uses opposite enable polarity. Obtain the distributor's written confirmation of exact package and reel/cut-tape service; a complete suffix-by-suffix decoding was not verified here.
Sourcing Advice
Buy through the manufacturer or a distributor whose Vishay franchise status is confirmed at ordering. Avoid anonymous marketplace stock or brokers without traceable original packaging and lot documentation. Check the full MPN, package drawing, enable polarity, date/lot traceability, and packaging quantity; do not use distributor electrical summaries to override the manufacturer datasheet. No live stock or lead-time guarantee is made by this guide.
Sources
Vishay Siliconix — SiP32431DN, SiP32431DR, SiP32432DN, SiP32432DR datasheet, document 66597, S20-0532 Rev. G, July 6, 2020. Used for electrical limits, recommended operation, pinout, capacitors, enable polarity, reverse-blocking behavior, and thermal constraints.
Vishay — SC-70 package information included in the same PDF, document 73201, ECN S-42145 Rev. A, November 22, 2004. Used for the mechanical dimensions and 0.65 mm lead pitch.
Texas Instruments — TPS22917 datasheet, Rev. B as identified by the official product page. Used to verify functional-alternative capabilities, package, active-high control, current, quiescent current, and reverse-current activation threshold; revision date not verified in this research.
Texas Instruments — TPS22916 datasheet, Rev. F as identified by the official product page. Used to verify the CN variant, package and ordering code, voltage/current range, and reverse-blocking behavior; revision date not verified in this research.
JLCPCB exact-part catalog entry C141606. Used only for catalog identification relevant to assembly sourcing; stock and assembly allocation remain to be checked.
Verification limits: No cross-manufacturer drop-in replacement, present cut-tape MOQ, complete packaging-suffix decoding, actual-board thermal performance, or library-footprint correctness was verified. Engineering recommendations in this guide—such as the optional control pull-down and power-domain sequencing—are explicitly distinguished from manufacturer requirements.