I’ll use this brief to research the XY301V-A-5.0-2P, verify its electrical/mechanical specifications, and create the application guide as a project document.
The XY301V-A-5.0-2P is a two-position, 5.0 mm-pitch, through-hole PCB screw terminal block manufactured by Ningbo Xinlaiya Electronics. It is commonly used to terminate field wiring for board power inputs, power outputs, and low-speed control signals where a removable wire-to-board connection is not required.
1. Quick Specifications
Rating terminology: The available manufacturer-family documentation publishes rated voltage and current, not semiconductor-style absolute maximum and recommended operating tables. Treat 300 V and 15–16 A as connector ratings that still require application-specific derating, suitable PCB spacing, adequate copper, correct wire size, and compliance review.
The XY301V-A-5.0-2P is a two-position, 5.0 mm-pitch, through-hole PCB screw terminal block manufactured by Ningbo Xinlaiya Electronics. It is commonly used to terminate field wiring for board power inputs, power outputs, and low-speed control signals where a removable wire-to-board connection is not required.
1. Quick Specifications
Rating terminology: The available manufacturer-family documentation publishes rated voltage and current, not semiconductor-style absolute maximum and recommended operating tables. Treat 300 V and 15–16 A as connector ratings that still require application-specific derating, suitable PCB spacing, adequate copper, correct wire size, and compliance review.
Table
Parameter
Verified value
Classification / notes
Manufacturer
Ningbo Xinlaiya Electronics (XINLAIYA / XINYA)
Manufacturer identification is consistent across LCSC, JLCPCB, and the manufacturer-series catalog
Configuration
1 row × 2 positions
Two electrically independent terminals
Pitch
5.0 mm
Center-to-center pin spacing
Mounting
Through-hole, straight/vertical PCB pins
Wave-solder compatible according to JLCPCB listing
Rated voltage
300 V
Published rating; not an independently verified absolute maximum
Rated current
15 A on the exact LCSC/JLCPCB listing; 16 A in the XY301V-A family catalog
Use 15 A maximum for this ordering code unless the manufacturer confirms otherwise
Accepted conductor range
14–22 AWG; up to 1.5 mm²
Published listing/family data
Screw
Exact listing: M2.5; family catalog: M2.6
Ordering-code discrepancy—verify production samples before specifying automated tooling
Recommended tightening torque
0.4 N·m
XY301V-A family catalog value
Housing
PBT, UL 94 V-0
XY301V-A family catalog value
Solder pins
Tin-plated brass
XY301V-A family catalog value
Wire protector
Stainless steel
XY301V-A family catalog value
Operating temperature
Not verified
LCSC/JLCPCB leave this field blank; do not assume a range
Color
Blue
Exact distributor listing
Compliance
RoHS listed
Confirm certificates and date codes for regulated production
2. Pinout & Connections
The connector has no fixed polarity or signal assignment. Pin names should be assigned by the circuit designer to match the board function and silkscreen.
Table
Pin Number
Pin Name
Description
Best Practice
1
User-defined (for example, VIN+, LINE, OUT+, or SIGNAL_A)
First independent screw-clamp terminal connected directly to PCB pin 1
Mark polarity/function clearly on silkscreen; route with copper sized for the actual current; do not rely on connector color for polarity
2
User-defined (for example, VIN−, RETURN, OUT−, or SIGNAL_B)
Second independent screw-clamp terminal connected directly to PCB pin 2
Maintain required clearance from pin 1 for the working voltage; use a deliberate return path rather than automatically assigning chassis or signal ground
Pin numbering must be checked against the footprint’s pin-1 marker and the physical wire-entry orientation before PCB release. For AC mains or other hazardous voltages, polarity conventions such as line/neutral must also be documented on the enclosure and assembly drawing.
3. Standard Application Circuit
Typical DC power input
Assign pin 1 to the positive input and pin 2 to the return only if that convention matches the product wiring scheme.
Route the connector first into appropriate protection: fuse or resettable fuse, reverse-polarity protection where applicable, surge/TVS protection where applicable, and then the downstream power stage.
No passive component is intrinsically required by the terminal block itself. Protection and filtering values must be selected from the source voltage, fault-current capability, transient environment, and downstream load.
Place polarity and voltage-range markings next to the wire-entry side so they remain visible after assembly.
Typical switched or high-current output
Route both outgoing and return current paths with matched current capacity.
Put the switching/protection device close enough to minimize high-current loop area, but preserve screwdriver and wire-access clearance around the terminal block.
If the load is inductive, place the flyback, TVS, RC snubber, or other suppression element according to the switching topology; the connector itself provides no transient suppression.
Wire preparation and termination
Use conductors within the published 14–22 AWG / 1.5 mm² range.
Strip only enough insulation for the conductor to sit fully inside the clamp; no bare copper should remain exposed outside the housing.
Use ferrules for fine-stranded conductors when required by the applicable wiring standard or production process. Do not tin stranded wire ends before screw clamping because solder creep can reduce clamp force over time.
Tighten to the manufacturer-family value of 0.4 N·m only after confirming the screw variant on production samples.
4. PCB Layout & Routing Guidelines
Place the terminal block at a board edge with the wire-entry opening and screwdriver path unobstructed. Check the real 3D model and enclosure wall before release.
For high current, use short, wide copper pours on both layers with multiple stitching vias where layer transitions are necessary. Size copper using an IPC-2152-based calculation for copper thickness, allowable temperature rise, ambient conditions, and duty cycle; the connector’s 15 A rating does not mean an arbitrary PCB trace can carry 15 A.
Avoid thermal-relief spokes on pads carrying near-rated continuous current unless the spoke geometry is verified thermally. Solid pad connections improve current capacity but may require controlled preheat or wave-solder settings.
Preserve creepage and clearance appropriate to the actual working voltage, pollution degree, material group, coating, and regulatory standard. A 5.0 mm pitch alone does not establish approval for every 300 V application.
Add mechanical copper and annular-ring margin around the through-hole pads because wire insertion, screw tightening, and field servicing transfer force into the solder joints. Do not place fragile components or narrow board tabs directly behind the connector.
5. Common Pitfalls / Things to Watch Out For
Designing the PCB copper for less current than the connector rating. Connector current, wire ampacity, copper temperature rise, terminal contact resistance, and enclosure temperature must all be evaluated separately; the lowest limit governs.
Assuming all 5.0 mm terminal blocks are drop-in replacements. Body width, depth, pin diameter, board-edge setback, wire-entry direction, screw access, polarization features, and drill size can differ even when pitch and position count match.
Additional concern: the exact listing reports an M2.5 screw while the XY301 family catalog reports M2.6. Confirm samples before purchasing torque-controlled bits, designing a service tool, or freezing mechanical drawings.
6. Popular Alternatives & Equivalents
No cross-manufacturer replacement was verified as a guaranteed drop-in replacement from authoritative dimensional drawings. The following are sourcing candidates that require footprint, drill, body-envelope, voltage/current, wire-range, and approval comparison before substitution.
Table
Alternative
Compatibility classification
Engineering note
CUI Devices TB001-500-02BE
Functionally similar; 5.0 mm pitch; drop-in compatibility not verified
Two-position PCB screw terminal candidate; compare pin diameter, body envelope, current/voltage rating, wire entry, and approvals
Molex 39543-3002
Functionally similar; 5.08 mm pitch; not footprint-compatible without review
Pitch differs by 0.08 mm and mechanical details differ; use only after footprint and enclosure validation
Phoenix Contact 1715721 / MKDS 1,5/2-5,08 family
Functionally similar; 5.08 mm pitch; not claimed pin- or footprint-compatible
Industrial terminal-block option with different mechanical and commercial characteristics; verify exact ordering code and approvals
Within the same manufacturer, XY300V-A-5.0-2P and related XY301 variants may appear similar, but they must not be treated as equivalents without a side-by-side manufacturer drawing and rating comparison.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
LCSC lists the exact part as C557651. JLCPCB lists it for PCBA as an extended part. Other marketplace listings exist, but authorization status was not verified.
Packaging Options
Bag/bulk packaging; LCSC reports 800 pieces per full bag. This is not a tape-and-reel component.
Standard MOQ
LCSC’s live listing has shown a 5-piece minimum/multiple; JLCPCB PCBA has shown a 1-piece minimum. MOQ, stock, and price are dynamic and must be rechecked at purchase time.
Sourcing Advice
Match the full ordering code XY301V-A-5.0-2P and LCSC code C557651. Confirm 5.0 mm pitch—not 5.08 mm—plus wire-entry orientation, screw size, housing material, approvals, and production lot consistency. Buy from traceable distributors for regulated products and request current RoHS/UL documentation where required.
Sources
Ningbo Xinlaiya / XINYA XY301 screw-terminal-block family catalog — manufacturer-family technical catalog mirrored by Crest Technologies; includes XY301V-A(5.0) materials, ratings, torque, and series drawings. Document revision/date was not visible in the extracted source.
LCSC — XY301V-A-5.0-2P, C557651 — exact ordering-code specifications, stock, packaging, and price data; dynamic page accessed September 2026.
2304140030_Ningbo-Xinlaiya-Elec--XY301V-A-5-0-2P_C557651.pdf — exact-part PDF URL; automated text extraction was unavailable, so claims not independently readable from this PDF are explicitly marked unverified or supported by the family catalog/listing.
JLCPCB — XY301V-A-5.0-2P, C557651 — exact part attributes, assembly classification, MOQ, and related parts; dynamic page accessed September 2026.
Verification limits
Operating temperature, exact body dimensions, recommended PCB hole diameter, agency file numbers, insulation withstand voltage, screw-head geometry, and guaranteed cross-manufacturer drop-in replacements could not be verified from accessible authoritative text. Obtain the current manufacturer-controlled drawing or inspect qualified samples before using this connector in safety-critical, mains, high-vibration, or tightly constrained mechanical applications.