The exposed pcb pads of J1 I think is not long enough. It should be long enough to penetrate a female usb connector. So you have to search for how deep they usually are
I’ll look up USB-A mating dimensions and compare them with the exposed length of J1 and the enclosure’s front edge. The important measurement is the unobstructed length from the PCB tip to the enclosure—not just the copper pad length.
Your concern is justified: the PCB currently projects only 5.35 mm beyond the enclosure, while the USB-A drawing specifies at least 11.75 mm from the plug tip to its housing shoulder. I also found that J1’s contact pads appear outside the saved PCB outline, so shortening the enclosure alone would not resolve the connector geometry.
The current enclosure leaves only 5.35 mm of PCB exposed in the insertion direction. This is too short to accept on the basis of the standard USB-A plug envelope. The earlier check that plastic ends before a J1 footprint boundary was not a USB mating check and must not be treated as one.
No PCB, copper, component placement, routing or enclosure geometry was changed during this research.
Sources and verified dimension interpretation
Primary geometry: Universal Serial Bus Specification Revision 2.0, Chapter 6, printed page 95, Figure 6-7 (Series A receptacle interface and mating drawing), and printed page 99, Figure 6-9 (Series A plug interface drawing). [Full specification mirror](https://alsa.mirrorservice.org/datasheets/usb/usb_20.pdf...
You’re right: the PCB projects only 5.35 mm beyond the enclosure, while the USB-A plug drawing specifies 11.75 mm minimum from the plug tip to the housing shoulder—not copper pad length.
I recommend targeting 12 mm of exposed tongue, approximately 6.65 mm more, while keeping the electronics covered; J1’s conflicting pad/outline coordinates must be resolved before changing the PCB, as detailed in USB-A Mating Clearance.
Should I proceed with that USB tongue revision and refit the enclosure around it?
Current revision — clean plain shells, no clips or latches
The latest user direction supersedes every prior clip/snap detail: all cantilevers, hooks, catches, release tabs, beads, grooves, windows and projecting snaps have been removed. The existing tray and cover nodes were updated in place, not duplicated. The result is a plain lower pocket and upper cover with a continuous U-shaped telescoping overlap, interrupted only by the necessary open USB end.
Measured enclosure size: 26.55 × 17.00 × 5.81936 mm. Height remains ultra-thin; width is reduced by 2.20 mm and length by 1.10 mm from the former clipped enclosure. PCB position, outline, thickness, component placements, connectivity and routing are unchanged. J2 is DNP/unpopulated by explicit user direction; no header volume is reserved. No population properties were changed as part of this mechanical-only revision.
Current assets and existing nodes
3D Model
3D Model
The model cards offer parametric source and pipeline-derived STEP, STL and other formats.
Table
Existing node
UID
Current asset
Enclosure base v2
51471368-5e1e-402e-aa49-a2f9780ee8f4
usb-token-base-plain-shell.build123d
Enclosure lid v2
f79882e0-9346-4ab3-b606-fcb9a4ceaea1
usb-token-lid-plain-shell.build123d
Final read-back: both current nodes enabled, installed position (0,0,0) mm, rotation (0,0,0), scale 1, Z-up, physical materials and edge display enabled. Existing ROOT attachment was not changed. Earlier v1 nodes remain disabled. The previously exploded lid position, Z=18.2402 mm, was replaced with the installed pose. Temporary render offsets were removed after rendering. No third enclosure concept or additional model node was created.
Exact dimensions and height accounting
All coordinates are mm in the shared project frame; PCB top is Z=0.
Table
Feature
Value
Enclosure X extents
-17.40000 … +9.15000
Enclosure Y extents
-8.50000 … +8.50000
Enclosure Z extents
-2.99936 … +2.82000
Assembled length × width × height
26.55000 × 17.00000 × 5.81936
PCB X/Y envelope
-14.5…14.5 / -5.6…5.6
PCB top / underside
0 / -1.29936
Floor inner surface
-1.79936
Floor thickness
1.20000
Underside-to-floor clearance, away from bearing lands
0.50000
Tallest actual populated top body
U1, Z=+1.12000
Lid inner roof / outer roof
+1.62000 / +2.82000
U1-to-roof clearance
0.50000
Roof thickness
1.20000
Base part Z range / height
-2.99936…-0.10000 / 2.89936
Cover part Z range / height
-1.30000…+2.82000 / 4.12000
Seam Z
-1.30000
Base lip top Z
-0.10000
Telescoping overlap height
1.20000
Joint radial clearance
0.20000 per side, 0.40000 total across opposing sides
Base lip / cover skirt wall thickness
1.20000 / 1.20000
Combined nominal wall/joint band
2.60000
PCB edge-to-base cavity wall clearance
0.30000 per side and rear
Rear exterior corner radius
2.60000
Upper fixed capture face Z
0.00000
Nominal upper side bearing overlap onto PCB
0.20000 per side
Base lip-to-upper cover shoulder clearance
0.10000
Height is exactly 1.2 + 0.5 + 1.29936 + 1.12 + 0.5 + 1.2 = 5.81936 mm. No additional vertical margin was introduced. No populated bottom package body projects below the board in the covered region, so the PCB underside controls the lower clearance. J1 contacts lie outside the enclosure. Solder and manufacturing variation not represented in library bodies remain physical-test uncertainties.
The user explicitly authorized 1.2-mm skins and approximately 0.5-mm component gaps instead of the conservative enclosure defaults; this revision retains that override. The upper perimeter is locally thicker inward to create rigid board capture, not a higher cavity.
Plain joint and rigid PCB location
The joint has smooth continuous side and rear surfaces, with no locking geometry. The 0.20-mm per-side fit is PROVISIONAL and deliberately favors easy slip assembly, not an aggressive interference fit. The constant radial clearance also follows the rounded rear corners. A slip fit locates the cover but does not guarantee that it stays closed. Do not describe it as a qualified friction lock.
The PCB drops vertically into the base. Four fixed, floor-rooted perimeter bearing lands support the underside at Z=-1.29936, using the previously checked safe regions:
Table
X interval
Y interval in PCB
Bearing area
-11.5…-9.5
+5.1…+5.6
1.00 mm²
+7.0…+8.5
+5.1…+5.6
0.75 mm²
-4.0…-3.0
-5.6…-5.1
0.50 mm²
+7.2…+8.5
-5.6…-5.1
0.65 mm²
These are rigid pocket surfaces, with no cantilever or undercut. Continuous fixed upper side walls overlap the PCB edges at Z=0 when closed, sandwiching the board against the lower lands. Smooth cavity walls locate its sides and rear. The nominal sandwich has no intentional preload; board thickness tolerance and printer error can prevent perfect simultaneous seating and must be tested.
Remaining limitation: the open USB direction has no positive forward end stop. A +X board displacement of 0.1, 0.5 or 1.0 mm causes no solid interference; axial restraint therefore depends on actual friction and the cover remaining closed. No PCB notch/hole or obstructing USB lip was invented. Unlike the previous revision, the board is intentionally not independently retained with the lid removed. Hardware: none.
Geometry validation
The current component positions and stackup were re-read. All 14 populated library STEP package bodies were transformed individually into the saved board frame, excluding DNP J2. The two compiled shell solids and their downloaded analytic STEP exports were checked.
Table
Check
Status and evidence
Base connected and valid
PASS: 1 solid, 711.9538 mm³, 34 faces
Cover connected and valid
PASS: 1 solid, 948.5296 mm³, 18 faces
Closed base/cover intersection
PASS: 0 mm³
PCB/plastic intersection
PASS: 0 mm³, intended bearing contacts excluded
Populated package/plastic intersection
PASS: 0 mm³ for every body
Minimum body/plastic distance
PASS: 0.50000 mm, controlled by U1
Four underside contact lands
PASS: measured 1.00, 0.75, 0.65 and 0.50 mm²
Upper fixed capture
PASS: lifting PCB 0.1 mm gives 0.88949 mm³ cover interference
Joint radial gap
PASS: measured minimum 0.20000 mm in isolated overlap band
Joint overlap
PASS: 1.20000 mm
Plastic in X≥9.4 insertion half-space
PASS: 0 mm³
Board vertical installation samples
PASS: lifts 8, 4, 2, 1, 0.5, 0.1 and 0 mm; every body/base intersection is zero
Cover vertical closure samples
PASS: lifts 8, 4, 2, 1.5, 1, 0.5, 0.25, 0.1 and 0 mm; all intersections zero
Downloaded STEP versus authored solids
PASS: zero boolean symmetric difference for each shell; valid single solids and zero closed intersection
Final node asset/pose/scale/enabled read-back
PASS; both current nodes assembled and old v1 nodes disabled
Support-free geometric print orientation
PASS as a geometric assessment; see print section
Real printed fit, friction, strength, USB mating
NOT VERIFIED
The minimum actual-body distances to plastic are: R1 1.2672, C1 1.12, U4 1.0015, C5 0.9126, Y1 0.719, C6 1.12, U1 0.5, C2 1.12, U2 0.520558, C7 1.12, U3 0.678, LED1 0.52, C4 1.12 and C3 1.12 mm. Thus the new capture surfaces do not sacrifice the intended component clearance.
Assembly: set the tray open-up, lower the PCB onto its four fixed lands, then lower the cover straight down until the perimeter seating faces meet. Removal reverses these steps; no tab, hook, flexure or tool-operated latch is present. Sampled paths plus straight prismatic wall geometry establish nominal clearance, not friction or tolerance qualification.
USB exposure and evidence limit
Every plastic feature ends at X=9.15, 0.25 mm behind the existing conservative X=9.4 insertion boundary. The entire declared USB tongue/contact region and its forward insertion half-space are therefore clear above, below and along both sides. PCB/J1 position is unchanged.
Actual female USB-A port compatibility remains unqualified: the pre-existing J1 footprint/copper extends beyond the stored board outline, and no exact female-port mating envelope or physical trial is available. This revision adds no intrusion into the declared insertion region, but it does not repair or certify the original board connector geometry.
Assembled and exploded renders
Both images were generated from the actual placed project geometry and visually inspected. The selection includes the current two shells and 14 populated package models, excluding disabled historical shells and DNP J2.
The exploded image temporarily moves only the base -6 mm and cover +8 mm in Z. Final saved transforms are assembled (zero offsets); the PCB never moved. The images show clean uninterrupted exterior shells with the former visible clip slots and local lid latches absent.
PETG support-free print plan and caveats
Process: PETG FDM, 0.4-mm nozzle, gray #9a9a9a. Nominal 0.2-mm layers are PROVISIONAL; use finer/adaptive layers or verify quantization at the 0.5-mm lower cavity and board-bearing planes.
Base: print floor exterior on bed, open side upward; slicer translation Z=+2.99936 mm. All raised walls/lands grow directly from the floor; there are no suspended lips or beams.
Cover: print roof exterior on bed, rotate X=180° and translate Z=+2.82 mm. The continuous rim and skirt rise from the roof with progressively shrinking cross-sections.
Geometric orientation check: each part has 448.4486 mm² bed-contact area and zero downward-facing non-bed faces in its recommended print orientation. No bridges, blind horizontal openings, support-trapping cavities or flexible projections remain. Both are designed for support-free printing.
The asset pipeline flags two downward faces on the cover in its installed orientation. This is expected and resolved by roof-down printing; installed orientation is not print orientation.
Printer/build volume and material shrinkage calibration are unknown; build-volume fit and slicer toolpaths are not verified. Overall parts are 26.55 × 17 mm in plan.
0.20-mm per-side slip clearance, 1.2-mm skins and 0.5-mm component gaps require a fit coupon and a physical trial. PETG shrinkage, elephant's foot, warpage, layer rounding and unmodeled solder can consume these allowances. Avoid forcing the board or cover.
No positive cover locking, pull-out force, axial board retention, impact resistance, thermal performance or ingress rating is claimed. The cover may be loose; friction must be calibrated on the actual printer.
Downloaded separate STEP shells were inspected. A complete PCB-plus-enclosure STEP assembly export was not performed.
Assigned scope status
Table
Assigned item
Status
Remove every flexible/discrete clip and latch
Completed
Regenerate only base/cover and update existing nodes
Completed
Preserve 5.82-mm-class height and close actual-body clearances
Completed, 5.81936 mm
Validate body collisions, plain joint and support-free orientations
Completed; actual female-port qualification remains blocked by missing trustworthy mating geometry and pre-existing footprint/outline inconsistency
Assembled and exploded renders
Completed and inspected
Exact dimensions, assets/nodes and caveat report
Completed
Physical print/fit/friction/USB trial
Unattempted, no physical hardware
This batch completes the user-directed CAD simplification, not physical product qualification. There were no required CAD repair cycles: the initial plain-shell solids passed the geometry checks. Historical 11.5-mm, 11.21936-mm and clipped 5.81936-mm versions are superseded as current design authority. enclosure-design-and-validation remains historical context.
Current revision — clean plain shells, no clips or latches