Pico 2 Footprint Fix


Task
Correct this published Raspberry Pi Pico 2 Shield part's PCB footprint without changing its schematic terminals/symbol or terminal numbering.
Authoritative geometry
Use official Raspberry Pi Pico 2 Datasheet Release 5, Section 3 Figures 3–4:
https://pip-assets.raspberrypi.com/categories/1005-raspberry-pi-pico-2/documents/RP-008299-DS-3-pico-2-datasheet.pdf
  • Module body: 51 × 21 mm.
  • 40 main user pins are two rows of 20, 2.54 mm longitudinal pitch, 17.78 mm row center spacing (x = ±8.89 mm about center), with 1.0 mm finished holes on the Pico itself.
  • USB connector at top end. Pin 1 is top-left; pins 1→20 run top-to-bottom on left. Pins 21→40 run bottom-to-top on right; pin 40 top-right.
Required footprint
Make it a carrier socket footprint for two standard 1×20, 2.54 mm-pitch female through-hole header rows receiving a Pico fitted with male headers:
  • Exactly the 40 main pins (terminal numbers 1–40) must have plated through-hole pads in the standard arrangement.
  • Set each to padHoleType: STD, holeSize: 1.0mm (or 1.02mm if needed for standard 0.64mm square header posts), copper pad diameter/size 1.7–2.0 mm with adequate annular ring, connectedLayers All / top+bottom. Use a rectangular pin-1 pad and circular/round pads for the others.
  • Do NOT make SWCLK/GND/SWDIO debug terminals 41–43 into carrier header holes; omit their copper pads from the default footprint if possible, while preserving schematic terminals.
  • Keep/repair body/fab/courtyard/silkscreen outline for 51×21 mm module, clearly mark USB/top end and pin 1. The USB end must be unambiguously at +Y/top; include connector-access outline/overhang indication if supported.
  • Preserve the existing 3D model if correctly aligned; verify orientation with USB at +Y.
Validation
Read back all pads. Confirm 40 and only 40 plated header pads, x-row spacing 17.78mm, y pitch 2.54mm, pin mapping/orientation above, hole and annular geometry, body outline 51×21mm, and no footprint DRC errors. Publish a new version and report the new version/URL and exact geometry.
I’m blocked because this published project is view-only for your account, so I cannot edit or publish a new part version.
Please either fork the part/project into your workspace or grant edit access, then send the writable project URL. I can then correct the footprint, verify all 40 pads and mechanical geometry against Datasheet Release 5, run DRC, and publish the revised version.
Use my writable fork
Review geometry first
Explain access setup

Waiting for input


Name
Pin #
Type
Section
Pin Group
Orientation
Order
Sub-symbol
Terminal Type
GPIO0
1
Unspecified
UART
Left
bidi
GPIO1
2
Unspecified
UART
Left
bidi
GND
3
Unspecified
Power
Gnd Right
Right
powerIn
GPIO2
4
Unspecified
GPIOs
bidi
GPIO3
5
Unspecified
GPIOs
bidi
GPIO4
6
Unspecified
I2C
Right
bidi
GPIO5
7
Unspecified
I2C
Right
bidi
GND
8
Unspecified
Power
Gnd Right
Right
powerIn
GPIO6
9
Unspecified
GPIOs
bidi
GPIO7
10
Unspecified
GPIOs
bidi
GPIO8
11
Unspecified
GPIOs
bidi
GPIO9
12
Unspecified
bidi
GND
13
Unspecified
Power
Gnd Right
Right
powerIn
GPIO10
14
Unspecified
GPIOs
bidi
GPIO11
15
Unspecified
GPIOs
bidi
GPIO12
16
Unspecified
GPIOs
bidi
GPIO13
17
Unspecified
GPIOs
bidi
GND
18
Unspecified
Power
Gnd Right
Right
powerIn
GPIO14
19
Unspecified
GPIOs
bidi
GPIO15
20
Unspecified
GPIOs
bidi
GPIO16
21
Unspecified
GPIOs
bidi
GPIO17
22
Unspecified
GPIOs
bidi
GND
23
Unspecified
Power
Gnd Right
Right
powerIn

Raspberry Pi Pico 2 Shield