I’ll research the PTS810SJK250SMTRLFS from C&K primary documentation, verify ratings and mechanical details, then create the application and usage guide as a project document with citations.
Core electrical and mechanical specifications are verified. I’m now checking distributor packaging and credible substitute switches; any unverified footprint interchangeability will be labeled explicitly.
The PTS810SJK250SMTRLFS is a compact, top-actuated, momentary SPST normally-open tactile switch with J-bend SMT terminals. It is commonly used as a low-voltage human-interface input for MCU GPIOs in control panels, remote controls, handheld products, and keyless-entry devices.
1. Quick Specifications2. Pinout & Connections
The manufacturer evidence confirms a two-contact SPST-NO function, but the datasheet text does not assign electrical names to numbered terminals. This Flux part uses terminals 1 and 3; they are electrically interchangeable because the switch contact is non-polarized.
Important: Do not infer footprint interchangeability from body dimensions alone. Pin numbering and terminal geometry must be check...
It covers verified specifications, terminal connections, GPIO integration and debouncing, PCB guidance, common pitfalls, qualified alternatives, and sourcing. No cross-manufacturer drop-in replacement was confirmed, so alternatives are clearly marked as requiring footprint verification.
The PTS810SJK250SMTRLFS is a compact, top-actuated, momentary SPST normally-open tactile switch with J-bend SMT terminals. It is commonly used as a low-voltage human-interface input for MCU GPIOs in control panels, remote controls, handheld products, and keyless-entry devices.
1. Quick Specifications
Table
Parameter
Classification
Value
Engineering note
Contact arrangement
Functional
SPST, normally open; momentary action
Open when released and closed while pressed.
Maximum switched voltage
Absolute maximum rating
16 VDC
Do not use this as a recommended design voltage.
Maximum switched current
Absolute maximum rating
50 mA DC
Intended for signal-level switching, not direct load or power switching.
Contact resistance
Electrical characteristic
≤500 mΩ
Account for this only in unusually low-voltage or precision sensing paths.
Insulation resistance
Electrical characteristic
≥100 MΩ
Applies with the switch open.
Dielectric strength
Electrical limit
250 VAC for 1 minute
Production withstand specification; not a working-voltage recommendation.
Operating temperature
Operating condition
−40°C to +85°C
Storage-temperature range was not found in the supplied manufacturer datasheet.
Operating force
Mechanical characteristic
260 ±70 gf (approximately 2.55 N nominal)
White actuator variant.
Travel
Mechanical characteristic
0.15 ±0.10 mm
Short-stroke tactile action.
Operating life
Durability
50,000 operations
Verify product-level duty-cycle requirements against this rating.
Bounce time
Switching characteristic
≤10 ms
Debounce in firmware or hardware.
Body envelope
Package
4.2 × 3.2 mm footprint; 2.5 mm height
Confirm the official recommended land pattern before PCB release.
Termination
Package
J-bend SMT
Designed for reflow assembly.
Recommended use voltage
Recommended operating condition
Not separately specified by the manufacturer
3.3 V or 5 V GPIO sensing is comfortably below the switch maximum when current is limited by a pull-up.
2. Pinout & Connections
The manufacturer evidence confirms a two-contact SPST-NO function, but the datasheet text does not assign electrical names to numbered terminals. This Flux part uses terminals 1 and 3; they are electrically interchangeable because the switch contact is non-polarized.
Table
Pin Number
Pin Name
Description
Best Practice
1
Contact A
One side of the normally-open momentary contact
Commonly connect to GND for an active-low GPIO input. It may instead connect to the sensed signal if the other terminal goes to GND or a rail through a current-limited network.
3
Contact B
Other side of the normally-open momentary contact
Commonly connect to the MCU input and a pull-up resistor. No polarity requirement applies.
Important: Do not infer footprint interchangeability from body dimensions alone. Pin numbering and terminal geometry must be checked against the latest manufacturer drawing and the PCB footprint used in the design.
3. Standard Application Circuit
Active-low MCU pushbutton
The most common implementation connects one switch terminal to GND and the other to an MCU GPIO input:
Add a 10 kΩ pull-up from the GPIO node to the MCU I/O supply (3.3 V or 5 V). The MCU's internal pull-up may be used when its tolerance and leakage performance are acceptable.
Connect terminal 1 to GND and terminal 3 to the GPIO node, or swap them; the contact is non-polarized.
Configure the firmware input as active-low: released = logic high, pressed = logic low.
Apply 10–20 ms firmware debounce, since the specified contact bounce can be as long as 10 ms.
No decoupling capacitor is required for the switch itself.
At 3.3 V with a 10 kΩ pull-up, the closed-contact current is approximately 0.33 mA. At 5 V, it is approximately 0.5 mA. Both are far below the 50 mA maximum rating.
Optional hardware filtering
For long traces or electrically noisy environments, place a 100 nF capacitor from the GPIO node to GND near the MCU and retain firmware debounce. This creates a 1 ms nominal RC time constant with a 10 kΩ pull-up, reducing narrow interference pulses without attempting to absorb the full worst-case bounce interval. If the signal enters a non-Schmitt input, use a Schmitt-trigger buffer or rely on a timer-based digital debounce rather than selecting an excessively slow RC edge.
If the user-accessible button is exposed to likely ESD injection, consider a low-capacitance ESD protector at the exposed interface and a small series resistor near the MCU input. These are system-level protections, not components required by the switch datasheet.
4. PCB Layout & Routing Guidelines
Use the manufacturer-recommended land pattern, not merely the 4.2 × 3.2 mm body outline. The retrievable datasheet confirms that a PCB-layout drawing exists, but its numeric pad dimensions were not available as machine-readable evidence.
Place the switch so enclosure buttons or plungers load the actuator vertically and concentrically. Side loading can degrade feel, life, alignment, or solder-joint reliability.
Keep copper and tall components clear of the actuator and moving enclosure features. Include assembly and enclosure tolerances around the 2.5 mm switch height.
Ordinary signal traces are sufficient; high-current trace sizing and thermal relief are not applicable because this part is limited to 50 mA and should not switch loads directly.
Place any debounce/filter capacitor and ESD protection near the receiving MCU or exposure point, respectively. Keep the GPIO trace away from fast switching nodes, antennas, and high-dV/dt power circuitry.
The switch is specified for infrared reflow soldering in accordance with IEC 61760-1. The supplied datasheet does not provide a numeric reflow profile or hand-soldering limit, so qualify the assembly profile with the manufacturer and contract manufacturer before production.
5. Common Pitfalls / Things to Watch Out For
Omitting debounce. A single press can produce multiple GPIO transitions because bounce time is specified up to 10 ms. Use timer-based firmware debounce or a correctly designed hardware debounce circuit.
Treating the switch as a load switch or assuming a similar-looking footprint is interchangeable. The contact rating is only 50 mA at 16 VDC maximum, and body-size equivalence does not prove land-pattern, actuator, or pick-and-place compatibility.
Additional production concern: do not apply enclosure preload that holds the actuator partially depressed. Maintain stack-up clearance across PCB, switch, enclosure, and keycap tolerances.
6. Popular Alternatives & Equivalents
No cross-manufacturer verified drop-in replacement was identified from the available primary-source evidence. The following parts are credible functional or mechanical candidates, but their terminal land patterns, tape orientation, coplanarity, actuator geometry, and assembly process must be compared drawing-by-drawing before substitution.
Table
Alternative
Manufacturer
Similarities
Compatibility classification
SKRPACE010
Alps Alpine
4.2 × 3.2 × 2.5 mm, top-push, 2.55 N, 50 mA at 16 VDC, 50,000 cycles
Functionally and envelope similar; pin/footprint compatibility unverified.
SKRPASE010
Alps Alpine
4.2 × 3.2 × 2.5 mm, top-push, 2.55 N, 50 mA at 16 VDC; higher 500,000-cycle life
Functionally and envelope similar; pin/footprint compatibility unverified.
TC-S0403-2.5-260G
HCTL
4.2 × 3.3 × 2.5 mm, SPST, 2.6 N, 50 mA, 50,000 cycles
Functionally similar only; not footprint-compatible without redesign verification. It is rated 12 V rather than 16 V and has a wider body.
For the lowest-risk substitution, retain the exact PTS810 package and select another C&K/Littelfuse PTS810 force variant only if the altered operating force, actuator color, and life rating are acceptable. Even within the same series, preserve the full ordering code and confirm the manufacturer drawing revision.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
LCSC lists the part as C221896. The part is also commonly listed by DigiKey, Mouser, TME, and other franchised or authorized distributors. Check live stock and authorization status at purchase time.
Packaging Options
Manufacturer ordering code SMTR denotes tape and reel. Distributor cut tape and custom reel services may also be available.
Standard MOQ
Cut-tape listings commonly allow 1 piece. The manufacturer reel quantity is 2,900 pieces; distributor full-reel multiples may vary.
Sourcing Advice
Prefer franchised distributors and preserve the complete ordering code PTS810SJK250SMTRLFS. Confirm the SJK force option, 250 height, SMTR tape-and-reel packaging, and LFS lead-free/silver-plated suffix. Avoid untraceable marketplace inventory for production because mixed force variants and relabeled reels may be visually difficult to detect.
Stock and price are volatile and should be rechecked immediately before procurement. Do not approve an alternate solely from parametric-search dimensions; compare the official mechanical drawing, recommended PCB land pattern, actuator force/travel, reel orientation, temperature range, and switching ratings.
Littelfuse / C&K PTS810 Series datasheet — manufacturer datasheet; the accessible source did not expose a clear revision date, so revision/date remains unverified.