Light Pipe Design


Created a parametric set of four individual clear-PETG light pipes, aligned with the existing lid holes and LEDs.

3D Model

; detailed parameters are in Light Pipe Insert.
Open items
  • The Ø2.85 mm stems have a tight provisional friction fit in the Ø3.0 mm holes.
  • Physical fit, brightness, and optical crosstalk require a test print.
Recommended next steps
  1. Print caps-down in transparent PETG with supports disabled and a removable 3–5 mm brim.
  2. Use solid infill, slow external walls, and verify that the slicer shows four separate parts.
  3. Test one pipe first; lightly sand or polish the optical ends if needed.

Integral Clip Retry Results
Final integration attempt — latest status
BLOCKED; prior base restored and directly verified. At the user's explicit request, the compiled candidate was temporarily activated on the existing base node, preserving its exact datum. Four board views still omitted the enclosure and both clips. The candidate was therefore removed from the active base assignment, not left unverified in the assembly. The original build report below describes the earlier CAD-only batch; this section supersedes its activation/read-back status.
Assigned final-integration items

Table


ItemStatusEvidence / blocker
1. Place/activate candidate in existing datum; preserve old assetCompleted temporarilyOnly asset and active on node e1624f1e-3622-4d57-a788-d32b786cb9e0 were written. Direct read-back confirmed candidate storage URL, computed.active=true, position (45,-50,0) mm, rotation (0,0,0), unit 3D scale. Old asset was not changed or deleted.
2. Assembled seated-board views: left, right, relay front/isoFailed / blockedAll four requested views rendered successfully as images, but showed the PCB/components only, with no enclosure or clips. They are not assembled candidate evidence.
3. Prove root/arm PCB clearance in assemblyFailed / blockedCandidate absent from views. Prior nominal source/kernel clearance evidence remains valid for that limited scope; it does not satisfy the assembled gate.
4. Prove >=0.6 mm outward travel and simultaneous accessFailed / blockedNo candidate/wall/relay assembly view or motion/access verification. Prior beam calculation alone is insufficient.
5. Confirm visible integral floor/side attachmentFailed / blocked for assembled viewPrior compiled one-solid result and candidate-only renders remain available, but requested assembled visibility is absent.
6. Confirm unchanged openings/lid interfaceCompleted for preservation; visual gate blockedNo CAD source, opening, lid or interface geometry was changed in this integration attempt. Prior source preservation evidence remains; assembled alignment could not be inspected.
7. Restore previous base if any gate/view failsCompletedRestored exact prior asset and removed the temporary explicit active rule. Fresh direct read-back confirmed prior URL, computed.active=true, unchanged datum and scale.
No final candidate activation was retained. This restores the pre-test base assignment; it does not certify the old clip geometry, which has separate known review findings.
Direct model read-back and rollback evidence
Use get_layout(mode=scene_tree, designators=['Wall Enclosure Base — PETG'], includeRulesets=true, includeSystemDefaults=false, compact=false) to retrieve the full inline and computed rules. With includeRulesets=false, this interface omitted those properties even for a single model. This resolves the prior report's direct-property visibility limitation.
During test: asset=enclosure-base-integral-clips-retry.build123d, active=true, computed.active=true, computed.storageName=document_assets/enclosure-base-integral-clips-retry-d1a671e0-0271-4f00-af48-d0a7a42bf503.build123d.
After rollback: asset=water-level-enclosure-base-pcb-snap-clips.build123d; no explicit active rule, matching the initial state; computed.active=true; computed.storageName=document_assets/water-level-enclosure-base-pcb-snap-clips-0e293c94-757d-40a0-999d-f12955fa62c1.build123d. Both reads: position 45mm -50mm 0mm, rotation 0 0 0, scale 1, computed.scale3d {x:1,y:1,z:1}, zIsUp/physicalMaterials/showEdges true. No position/rotation/scale writes were made.

3D Model

3D Model

Render evidence — candidate was enabled, but omitted
The board renderer produced a fresh export key document_assets/esp32-dual-ultrasonic-water-level-monitoring-system-91484c50a05f219a84e9d8fb9a3b05ea.glb after activation. All views below contain the PCB/components only. They establish the missing-view blocker, not mechanical clearance.
The editor-focus call also reported no requester frontend session. An internal feedback submission was attempted but failed; no ticket/report submission is claimed. The next attempt needs a renderer/export that includes the enabled base model in the board assembly; repeat the mandatory rollback if it still does not.
Disposition
Compilation and connected-solid validation completed. Overall replacement release FAILED / BLOCKED at assembled validation; not activated. A new asset is retained only as an explicitly labelled validation candidate. No model node was added, changed, enabled, or replaced; the PCB, active base assignment, lid, plungers and other models were left untouched.

3D Model

Asset name: enclosure-base-integral-clips-retry.build123d; UID 5004432e-620f-4d2b-938c-1a9b95aa8253. The durable asset card offers source and pipeline-derived STEP/STL/3MF downloads, but existence of those exports is not fabrication approval.
Scope status

Table


Assigned itemStatusEvidence or specific blocker
Retry complete Build123d base through real asset pipelineCompletedAsset compilation succeeded; geometry report returned. This attempt did not depend on Build123d being installed in the code sandbox.
Fuse floor pedestal, compliant arm, hook/lead-in and release tab into baseCompletedEvery sequential union asserts exactly one valid solid; final report is one solid. Floor pedestals overlap floor by 0.2 mm and side wall by 0.5 mm.
Verify no clip intersects seated PCBCompleted for nominal PCB laminateSource performs kernel intersections of both complete clips against the actual tapered narrow-edge PCB slab, Z=-1.50…0; rejects intersection volume above 1e-7 mm³. This is not a complete component/copper/solder contact qualification.
Retain lower support ledgesCompleted geometricallyExisting three 24 mm ledges retained unchanged, contact top Z=-1.50 mm.
Prove ledges avoid all component bodies and solder featuresFailed / blockedFull installed component/underside mesh collision test was not obtained. Previous contact-safety concerns remain unresolved; no claim of approved copper-free contact strips.
Establish release stroke and PETG strain estimateCompleted analyticallyIndependent beam calculation below accounts for clear length and rigid grip extension. Not FEA or measured peak strain.
Prove full outward sweep without wall/relay collision and accessible simultaneous operationFailed / blockedNominal dimension checks are favourable, but no actual assembled swept-volume or fingertip access verification was obtained. Sloped retaining faces can cam outward under lifting load and require retention-force testing.
Preserve relay/DC openings and wall mounting geometryCompleted at source/kernel levelDonor dimensions, subtraction locations, wall ears, keyholes, bosses and seam geometry retained; kernel window-interior probes passed.
Prove assembled opening alignment remains correctFailed / blockedReal board and candidate rendered separately, not as one candidate assembly.
Assess floor-down PETG printabilityCompleted assessment; not qualifiedElevated beam undersides require removable supports. Contact ramps are 45 degrees; no supports intended on hook or PCB ledge surfaces. Existing wide window roofs still need a slice/support plan.
Assembled candidate 3D read-back before activationFailed / blockedBoard renderer returned existing PCB without the candidate. Code sandbox had no mounted export attachments and no network, so real PCB GLB plus candidate STEP/GLB could not be combined or checked there.
Activate corrected base only after all gates passUnattempted / gatedIntentionally no node mutation because assembled and contact gates remain open.
This batch therefore produced a compiled, one-piece CAD candidate, not a validated replacement enclosure.
Starting geometry and preserved datum
Read the full 7315-character source of the indexed current base:

3D Model

Direct layout inspection confirms base node e1624f1e-3622-4d57-a788-d32b786cb9e0 under Root. Indexed node lookup identifies donor asset water-level-enclosure-base-pcb-snap-clips.build123d, position (45,-50,0) mm, zero rotation and unit scale. Direct scene-tree output omitted its asset/active/transform properties, so indexed assignment is not promoted to a fresh authoritative active-rule verification. No placement was changed.
Live normalized PCB outline is 89 × 99 mm with relay-side edges X=-40.728 and X=40.700…40.699 over Y=17.244…49.500 mm. Nominal PCB thickness is 1.50 mm, top Z=0. Source coordinates remain in this PCB-centred Y-up frame; root transform is not baked into the CAD.
The current task says to preserve DC openings, so this candidate preserves the donor's closed-top rectangular opening, not the closed-wall alternative mentioned in an older report. Four relay cuts: X centres -27.6024, -8.9379, 9.5017, 27.5676 mm, Y=52 mm, Z=5 mm; each cutting box is 16.8 × 5 × 10.8 mm. DC cutting box: X=47 mm, Y=-17.8063 mm, Z=5 mm; size 5 × 16.04 × 10.8 mm. Wall ears, keyholes, mounting bosses, shadow line, seam and lower ledges retain donor geometry.
Real pipeline evidence
mutate_project_assets compiled the complete source and returned:
  • Overall envelope 119 × 107 × 30.5 mm, including wall ears.
  • Volume 57,488.7486 mm³.
  • 1 solid, 163 faces; sole solid has the full reported envelope.
  • Findings: 11 down-facing planar faces, total 339.9766 mm², may need supports; reported location (-40.628,42,0.5) mm is on the left hook's deliberately 45-degree lower ramp.
  • No floating-solid finding was returned.
Hard source gates reject empty/invalid shapes, non-single-solid sequential unions, missing mandatory root fillets, seated PCB intersections, changed opening interiors, insufficient clear length and screening strain above 2%. Successful compilation executed those gates. This is stronger than inferring connectivity from a render.
Read-only asset enumeration confirmed the durable candidate name, URL, UID and 3D-model flag after creation. Three separate candidate renders succeeded:
Editor focus was attempted, but the requester frontend session was unavailable.
Exact candidate clip geometry
Dimensions are millimetres and remain provisional pending print qualification.

Table


FeatureDimensions / coordinates
Material/processPETG FDM, 0.4 mm nozzle, floor down at Z=-12
Side-edge magnitudesLeft 40.728; right reference 40.69925; actual right edge varies slightly with Y
Side clearance at beam0.200 nominal
Flexure thickness1.600 in X (XY bending)
Flexure vertical height5.500, Z=-1.500…4.000
Root pedestalY=18…23; Z=-9.8…4; from edge+0.2 to X magnitude 46; positive floor/wall overlap
Root fillet1.000 mm actual concave arm/pedestal fillet, selected by vertical junction topology; missing selection rejects build
Clear compliant length16.000, Y=24…40, excluding Y=23…24 root-fillet transition and Y=40…44 grip
Grip length4.000, Y=40…44
Hook inward extentEdge magnitude minus 0.400 nominal engagement; slight right-edge taper causes less than 0.0001 mm variation across grip
Hook XZ section, relative to side-edge magnitude e(e-0.4,0.8), (e+0.4,0), (e+0.4,3), (e-0.4,2.2)
Hook/arm positive overlap0.200 in X
Hook nose vertical thickness1.400
Insertion lead-in45 degrees, above PCB; no below-PCB diamond
Lower retaining face45 degrees, Z=0.4 at PCB edge and Z=0.8 at inward nose; not a zero-play horizontal locking shoulder
Outward release tabY=40…44; outer X magnitude e+3.2; top Z=3.4; outer tip thickness 1.4; 45-degree lower chamfer
Existing lower ledgesX=-39…-15, -12…12, 15…39; contact Y=48.5…49.5; top Z=-1.5
The lower hook slope avoids support on the fit surface but introduces vertical play and a cam-out possibility. Retention force and resistance to accidental upward removal are not qualified. Do not call this a proven positive-lock clip.
Independent release/strain calculation
For the 16 mm clear rectangular beam with a rigid 4 mm grip and outward force at grip centre, load distance a=18 mm. Require displacement at the leading edge of the entire grip d_L=0.600 mm (0.400 engagement + 0.200 removal clearance), rather than incorrectly checking only tab-centre movement.
k = d_L / [L²(a/2-L/6)] = 0.000370066 mm^-2 (the displacement coefficient F/EI).
  • End rotation theta = k L(a-L/2) = 0.0592105 rad = 3.3925 degrees.
  • Tab-centre outward displacement = d_L + 2 theta = 0.718421 mm.
  • Far hook edge displacement = d_L + 4 theta = 0.836842 mm.
  • Nominal root strain = k a t/2 = 0.532895%.
  • Conservative 2× screening allowance = 1.06579%, below 2%.
The independent code calculation returned these values. Its narrative labelled k with an incorrect inverse-length unit; dimensionally F/EI is mm^-2, corrected here. The 2× factor is an explicitly selected screening allowance, not a verified stress-concentration factor or peak-strain bound. Grip flexibility, torsion, nonlinear contact, notch stress, PETG creep and print anisotropy require physical or FEA qualification.
Nominal far-end tab outer extent is at most about 44.765 mm including the linearized stroke, against the locally rounded inner wall near 45.5 mm; about 0.73 mm remains by the simple envelope calculation. Nominal component-envelope X separations are favourable and outward motion increases separation from relays. These are not a substitute for the missing assembled swept-volume/finger-envelope check.
Floor-down printing and remaining gates
  • Pedestals are continuously fused to floor and side walls. Arms are integral but not support-free: their undersides are Z=-1.5 with floor top at -9.6, leaving an 8.1 mm gap. Use removable slicer supports under these non-contact beam undersides, then fully remove them so the 16 mm compliant span is free.
  • Keep supports off hook ramps, PCB ledge tops and contact/fit surfaces. Hook and tab lower faces are 45 degrees, nose sections 1.4 mm; those ramps require slicer inspection and a PETG coupon.
  • Existing relay/DC window roofs exceed the ordinary 10 mm bridge guideline (16.8/16.04 mm). Their corrected openings were intentionally not redesigned. A qualified bridge profile or removable support plan that does not spoil fit must be demonstrated; this remains an open printability gate.
  • Support scars under the arm, dimensional shrinkage, layer adhesion and root stress may change release behaviour. Print a two-clip coupon before the whole base; test seating, outward release, accidental lift resistance, simultaneous access, creep and cycles. No fatigue-life claim.
  • Before activation: obtain a true combined candidate+PCB 3D read-back in the preserved datum; check actual component/solder and ledge contacts; evaluate complete outward sweep and access; resolve retention cam-out/vertical play; approve the print support plan. Only then replace the existing base asset rule and independently read it back.
  • Final integration attempt — latest status

  • Assigned final-integration items

  • Direct model read-back and rollback evidence

  • Render evidence — candidate was enabled, but omitted

  • Disposition

  • Scope status

  • Starting geometry and preserved datum

  • Real pipeline evidence

  • Exact candidate clip geometry

  • Independent release/strain calculation

  • Floor-down printing and remaining gates