• Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
  • Ground
    A common return path for electric current. Commonly known as ground.
  • Net Portal
    A net identifier used to create connectivity to other Net Portal with the same designator. #portal
  • Power Net Portal
    Power net portal is a special schematic object used to define a power or ground net. Power ports allow you to conveniently indicate a power net at any location in the design. Power nets of the same designator automatically connect throughout your design #portal #power
  • Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
  • Generic Capacitor
    A generic fixed capacitor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
  • Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
  • 875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
  • CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
  • 1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
K
A

WP7113SYD

WP7113SYD
Description

Created
November 16th 2022
Last updated by jecstronic
2 years ago
1 Contributor(s)
jecstronic

Controls

Properties

Forward Voltage
2 V
Part Type
LED
Manufacturer Name
Manufacturer Part Number
WP7113SYD
Designator Prefix
LED

Availability & Pricing

DPNStockQty 1
17.2K$0.46
10$0.2237
10$0.45
116K$0.1357
10$0.0777

Assets

    Thumbnail
  • thumbnail
    Radial, D5.00mm H8.60mmLEDYellow.png

    id=Radial, D5.00mm H8.60mmLEDYellow

  • LED_D5.0mm.step

    id=3D

  • Footprint
  • LED_WP7113SYD.kicad_mod

    id=Footprint_V5

  • Default
  • thumbnail
    led-off.svg

    id=led-off

Simulation

µs

Simulation Speed

Crear ampolleta cálida con led uv
Crear ampolleta cálida con led uv
8mo
@copilot arma este circuito porfavor https://cdn2.flux.ai/flux-comment-files/f...
@copilot arma este circuito porfavor

Image


8mo
Claro, puedo proporcionarte la lista de conexiones basándome en la imagen que has proporcionado. El proyecto parece ser un circuito con un microcontrolador PIC y un cristal oscilador para generar la señal de reloj, además de un LED con su resistencia limitadora. Los siguientes puntos describen las conexiones según la imagen:

  1. Cristal Oscilador:

    • Connect C1:1 to U1:(OSC1/CLKIN)(OSC1/CLKIN)
    • Connect C1:2 to U1:(OSC2/CLKOUT)(OSC2/CLKOUT)
    • Connect C2:1 to U1:(OSC1/CLKIN)(OSC1/CLKIN)
    • Connect C2:2 to U1:(OSC2/CLKOUT)(OSC2/CLKOUT)
    • Connect X1:1 to U1:(OSC1/CLKIN)(OSC1/CLKIN)
    • Connect X1:2 to U1:(OSC2/CLKOUT)(OSC2/CLKOUT)
  2. LED con Resistencia Limitadora:

    • Connect D1:Anode to U1:(RC0/TOSO/T1CKI)(RC0/TOSO/T1CKI)
    • Connect D1:Cathode (through R2) to Ground (GND)
  3. Resistencia de Pull-up para el botón de reinicio:

    • Connect R1:1 to Vdd (+ fuente de poder)
    • Connect R1:2 to U1:(MCLR/Vpp/THV)(MCLR/Vpp/THV)
  4. Botón de Reinicio:

    • Connect the Reset button one side to U1:(MCLR/Vpp/THV)(MCLR/Vpp/THV)
    • Connect the Reset button other side to Ground (GND)
Estas conexiones deberían configurar correctamente el circuito según el diagrama esquemático provisto en la imagen. Recuerda conectar Vdd y Vss (tierra) a los pines correspondientes del microcontrolador PIC (no mostrados directamente en el esquemático). Además, ten en cuenta que las conexiones del LED pueden variar en función del pin utilizado del PIC para el manejo del mismo. Aquí estoy asumiendo que usarás el pin RC0/TOSO/T1CKI para manejar el LED, pero esto puede cambiar según las necesidades de tu programa y configuración.
8mo
Me puedes implementar el circuito en flux.ai para hacer la simulación
8mo
Como asistente de IA, no tengo la capacidad de interactuar directamente con aplicaciones o software, lo que incluye crear diseños o simulaciones en flux.ai. Sin embargo, puedo guiarte en cómo realizar la implementación del circuito en Flux paso a paso:

  1. Inicia una nueva sesión en Flux:

    • Abre tu navegador y accede a la página de flux.ai.
    • Inicia sesión con tu cuenta o regístrate si aún no tienes una.
    • Crea un nuevo proyecto de diseño de PCB.
  2. Agrega el microcontrolador PIC:

    • Utiliza la biblioteca de componentes para encontrar el microcontrolador PIC específico que estás usando y colócalo en tu esquemático.
  3. Agrega los cristales y capacitores:

    • Agrega el cristal oscilador X1X1 y los dos capacitores de carga C1C1 y C2C2 al esquemático.
    • Haz las conexiones entre los capacitores y el cristal como se mencionó anteriormente, asegurándote de que ambos se conecten a los pines de oscilación del microcontrolador.
  4. Agrega el LED y su resistencia limitadora:

    • Encuentra un LED amarillo en la biblioteca y colócalo en el esquemático.
    • Añade una resistencia de 220Ω220\Omega R2R2 y conéctala en serie con el cátodo del LED.
    • Conecta el ánodo del LED al pin del microcontrolador PIC que desees usar para la salida del LED (por ejemplo, RC0)\left(\text{por ejemplo, RC0}\right).
    • Conecta el otro extremo de R2R2 a tierra (GND)\left(GND\right).
  5. Agrega la resistencia de pull-up y el botón de reinicio:

    • Coloca una resistencia de 10kΩ10k\Omega R1R1 en el esquemático y haz la conexión entre Vdd y el pin MCLR del PIC.
    • Añade un interruptor (botoˊndereinicio)\left(botón de reinicio\right) y conéctalo entre el pin MCLR y tierra (GND)\left(GND\right).
  6. Conexionado de alimentación y tierra:

    • Asegúrate de que Vdd y Vss estén correctamente conectados al PIC, según las especificaciones del microcontrolador.
  7. Verifica y guarda tu esquemático:

    • Revisa todas tus conexiones para asegurarte de que coincidan con el diagrama de la imagen proporcionada.
    • Guarda tu proyecto.
  8. Prepara la simulación:

    • Si Flux soporta simulación, prepara el entorno de acuerdo con las instrucciones de Flux para simular el comportamiento del circuito.
Para datos o pasos más específicos, deberás referirte a la documentación o tutoriales de Flux, ya que cada herramienta CAD puede tener su propio conjunto de características y métodos de uso. Recuerda también revisar cualquier regla de diseño o comprobación de errores que Flux pueda ofrecer para asegurarte de que tu diseño es viable antes de proceder a la fabricación del PCB o la simulación.
8mo
Hey, I’m Copilot, your AI design assistant. I can help you brainstorm ideas, deb...
Hey, I’m Copilot, your AI design assistant. I can help you brainstorm ideas, debug problems, research components, and even make wiring connections for you. Ask me questions like:

  • @copilot I'm designing a PCB for a medical device that measures heart rate and temperature. Can you give me the list of components I will need?
  • @copilot How would I connect these parts to make the LED flash at 1kHz?
  • @copilot can you choose 4 digital pins on the ATMega328P-AU that I have here to use as GPIO given that I am already using some pins for reset, the external clock, UART, and I2C.
Chat with me by tagging @copilot on comments or in the chat.
1y
Someone is typing...
Checks that the power traveling across a given resistor is under its rating with 50% headroom.
Learn more
Checks that IC pins that require pull up or pull down resistors have them.
Learn more
Checks that capacitors have appropriate voltage ratings to prevent overheating and ensure reliable circuit operation.
Checks that all parts have a part number and are available from distributors.
Reports copper elements that are shorting.
Reports parts that have no footprint.
Reports nodes that are assigned to a layer that doesn't exist in the layout stackup.
Reports components that have been modified using the "!important" flag.
Reports terminals that are not connected properly. NOTE: Only connections to the center of pads are considered valid.
Reports nodes that are using rules that are not supported anymore.
Reports layers that have multiple copper fills of different nets. Make sure the Connected Layers rule value of nets with fills is valid.
Detect any via, trace or copper fill island that is not connected to any net.