Adding Pin Header Strip

louisb10

louisb10

Add to this pin header strip 5 pin

flux

I can’t add it in this project because it’s a read-only published part, not an editable design.
If you want, start an editable project here and continue from there: Create editable project
The current project is a published part project for ESP32-C3-DEVKITC-02 , and the part-creation guidance shows edits like adding terminals/components are only appropriate in an editable project or new part workflow .
If you want, I can also help you phrase the prompt for:
  • a straight 1x5 header
  • a right-angle 1x5 header
  • a specific 2.54 mm pitch version
Straight 1x5 prompt
Right-angle version
Expose named pins
Sign up to send
list all ICs and the decoupling capacitors attached to each. Ensure to include a...
serkank

serkank

@copilot list all ICs and the decoupling capacitors attached to each. Ensure to include all ICs present in the design, including digital ICs, power converters, LDOs, etc. For every IC, clearly state:
  • What power net the decoupling capacitors are attached to. What is the stated voltage of that net.
  • The voltage rating and value of the attached decoupling capacitors.
  • Signal with the expression “[WARNING]” if any of the following conditions are met: no decoupling capacitors are attached; the voltage of the power net is higher than the voltage rating of the capacitor; No voltage range was stated for the capacitor. Give a separate “[WARNING]” for each condition. Signal with the expression “[OK]” if none of those conditions are met
  • Express the result in a markdown-formatted table
2y

copilot

I'm sorry for any misunderstanding, but no ICs or decoupling capacitors have been described in the project details provided. The text only contains a list of unconnected pins on an ESP32 ESP32-C3-WROOM-02 Transceiver Evaluation Board from Espressif Systems. The descriptions do not include any information about decoupling capacitors, power converters, digital ICs, LDOs, or other ICs.
As a result, I can't provide the list and properties of decoupling capacitors or issue warnings about your project. However, in general, each power pin of an IC should have a decoupling capacitor connected to it, and the capacitance and voltage rating of the capacitor should be appropriate for the particular IC and power net. For the ESP32 series, a typical value for a decoupling capacitor is 0.1 μF, but the exact value may vary depending on the specific requirements of your design. Please add the necessary components to your project in Flux and then provide the updated project details for further assistance.
2y
Someone is typing...
2
GND
GPIO4
GPIO3
GND
GND
GPIO19
GPIO10
RST
3V3
GPIO20/U0RXD
GND
GPIO1/XTAL_32K_N
GND
GPIO9
5V
GPIO21/U0TXD
GND
GND
GPIO7
3V3
5V
GND
GPIO0/XTAL_32K_P
GPIO18
GND
GPIO6
GPIO2
GPIO5
GND
GPIO8
 

ESP32-C3-DEVKITC-02

ESP32-C3-DEVKITC-02 thumbnail
ESP32 ESP32-C3-WROOM-02 Transceiver; 802.11 b/g/n (Wi-Fi, WiFi, WLAN), Bluetooth® 5 2.4GHz Evaluation Board #CommonPartsLibrary #EvaluationBoard #RF #DevelopmentBoard #ESP32

Properties

Development Board

Espressif Systems

ESP32-C3-DEVKITC-02

docs.espressif.com/projects/esp-idf/en/latest/esp32c3/hw-reference/esp32c3/user-guide-devkitc-02.html

U

creativecommons.org/licenses/by/4.0/

Pricing & Availability

Distributor

Qty 1

Controls