AO3401A Footprint Fix


I’ll inspect the current terminal/pad bindings, correct only the mapping while preserving copper geometry, then verify and publish a new part version.
Blocked by permissions: you have view-only access to jecstronic/ao3401a, so I couldn’t edit or publish it.
Inspection confirmed:
  • Current incorrect mapping: S→pad 1, G→pad 2, D→pad 3
  • Required mapping: G→pad 1, S→pad 2, D→pad 3
  • The SOT-23 copper geometry is correct and should remain unchanged.
I filed a part-quality report with the Flux engineering team. To make and publish the correction directly, you’ll need edit access from the project owner or an editable fork.
I’ll research the AO3401A manufacturer datasheet and verified alternatives, then create a cited Application and Usage Guide in the project files. This task will not change the symbol, footprint, or published part version.
The guide is drafted with manufacturer ratings and replacement candidates. I’m tightening the gate-clamp guidance so the example circuit cannot be mistaken for a safe high-voltage design without resistor and power checks.
"AO3401A Guide" completed.
Created and reviewed the AO3401A Application and Usage Guide in the project files, covering specifications, high-side switching, layout, pitfalls, alternatives, and sourcing with citations. Unverified package-drawing and purchasing details are explicitly flagged; the symbol, footprint bindings, and published version remain unchanged.

AO3401A Application and Usage Guide
The AO3401A is a −30 V P-channel enhancement-mode MOSFET intended for high-side load switching and general power management. Its low-voltage gate characterization down to VGS = −2.5 V makes it useful with logic-controlled gate level shifting, but current capability remains strongly dependent on gate drive, PCB copper, ambient temperature, and duty cycle.
1. Quick Specifications

Table


AttributeValueClassification / Conditions
Drain-source voltage, VDS−30 VAbsolute maximum
Gate-source voltage, VGS±12 VAbsolute maximum; clamp the gate in circuits where the magnitude of VGS could exceed this value.
Continuous drain current, ID−4.0 A at TA = 25 °C; −3.2 A at TA = 70 °CAbsolute maximum, dependent on the datasheet PCB/thermal conditions; not a guaranteed application current.
Pulsed drain current, IDM−27 AAbsolute maximum pulse rating; application use must also satisfy pulse duration, SOA, and junction-temperature limits.
Junction temperature, TJ−55 to +150 °CAbsolute maximum range
RDS(on)41 mΩ typ., 50 mΩ max.Characterized: VGS = −10 V, ID = −4.0 A, TJ = 25 °C
RDS(on)47 mΩ typ., 60 mΩ max.Characterized: VGS = −4.5 V, ID = −3.5 A, TJ = 25 °C
RDS(on)60 mΩ typ., 85 mΩ max.Characterized: VGS = −2.5 V, ID = −2.5 A, TJ = 25 °C
PackageSOT-23 / TO-236, 3 leadsPackage identified by the AOS datasheet.
Lead pitchUnverified for this exact AOS package drawing0.95 mm is a common SOT-23 nominal pitch, not a verified dimension from this research. Verify the current AOS package drawing before footprint authoring.
2. Pinout & Connections
The working pinout is G = pin 1, S = pin 2, D = pin 3, consistent with the user-supplied convention and visually extracted AOS top view, but unverified by the automated datasheet extraction. Confirm the drawing directly in the linked AOS datasheet before creating or changing a footprint; this guide does not verify or correct this project's footprint bindings.

Table


Pin NumberPin NameDescriptionBest Practice
1Gate (G)Voltage-controlled input; a negative VGS turns the P-channel MOSFET on.Add a source-to-gate pull-up so the default state is off. Keep the magnitude of VGS below 12 V; add a gate-source Zener clamp when the input rail can exceed that limit.
2Source (S)Normally connects to the positive input rail in a high-side switch.Route with a short, wide connection and place the gate pull-up/clamp close to the source and gate.
3Drain (D)Switched output to the load.Use adequate copper area and width for load current and heat spreading; evaluate voltage drop using RDS(on) at the actual gate drive and temperature.
3. Standard Application Circuit
A practical logic-controlled high-side switch is:

Text


 VIN ─────────────── S (pin 2)
                        AO3401A
 VOUT / LOAD ─────── D (pin 3)
                         |
 MCU/CTRL ── 4.7 kΩ ─ B  Q1, small NPN
                       C ── 100 Ω ── G (pin 1)
 GND ──────────────── E

 G (pin 1) ── 100 kΩ ── S (pin 2)
 Optional: gate-source Zener clamp, cathode to S and anode to G
The 100 kΩ pull-up, 100 Ω gate series resistor, and 4.7 kΩ NPN base resistor are illustrative starting values for 3.3 V or 5 V rails and slow load switching, not AOS datasheet mandates or a qualified design. Add an illustrative 100 kΩ base-to-emitter pull-down to keep Q1 off when MCU/CTRL is high impedance. Pulling Q1 on brings the MOSFET gate low and turns the high-side switch on; releasing Q1 lets the pull-up return gate to source and turn it off.
Do not reuse the 100 Ω value blindly with a Zener clamp on a higher rail. Replace it with a calculated current-limiting pull-down resistor R_sink. During clamping, estimate I_sink ≈ (VIN − VZ − VCE(sat))/R_sink, and I_Z ≈ I_sink − VZ/R_pullup. Ensure positive sufficient clamp current, check resistor dissipation I_sink²R_sink, Zener dissipation VZ I_Z, and Q1 voltage/current ratings. Include supply transients, Zener tolerance and dynamic impedance, and overshoot when keeping VGS below the ±12 V absolute maximum. These are engineering sizing equations, not quoted AOS application formulas.
Check capacitive-load inrush against safe operating area and transient temperature; a series gate resistor alone does not establish a guaranteed soft-start ramp. Provide an appropriately oriented flyback diode or other energy clamp for inductive loads. This slow-switch example is not a validated PWM gate driver.
For a P-channel device in this orientation, the intrinsic body diode conducts from drain toward source; the AOS electrical table gives VSD about −0.7 V typical and −1.0 V maximum at IS = −1 A, VGS = 0 V. This means a powered VOUT can backfeed VIN through the body diode; use back-to-back MOSFETs or another reverse-current blocking method when true bidirectional isolation is required.
4. PCB Layout & Routing Guidelines
  • Keep the VIN-to-source and drain-to-load current paths short and wide; avoid neck-downs at pads and vias.
  • Use substantial copper connected to source and drain as permitted by the circuit to reduce resistive loss and spread heat; do not interpret the headline current rating independently of board thermal conditions. Avoid thin thermal-relief spokes in high-current paths; balance solid connections or adequately sized spokes against assembly solderability.
  • Place the gate pull-up, gate-series resistor, and any gate-source clamp close to pins 1 and 2 to minimize gate-loop area and susceptibility to dV/dt turn-on.
  • Keep sensitive control traces away from the high-current drain switching node. Place application-dependent rail bypass capacitors close to the supply/current loop; choose capacitance and rating for the load and source impedance rather than assuming a MOSFET-mandated value.
  • Estimate conduction loss with P ≈ I²RDS(on), using the maximum RDS(on) at the actual gate drive and adding margin for temperature rise.
5. Common Pitfalls / Things to Watch Out For
  1. Using threshold voltage as the full-on drive requirement. VGS(th) only indicates the onset of conduction at a small test current; use the characterized RDS(on) rows at −2.5 V, −4.5 V, or −10 V for loss calculations.
  2. Ignoring gate overstress and reverse current. A ground-referenced pull-down on a high VIN rail can exceed ±12 V VGS, and the intrinsic diode can backfeed the input from a powered output.
No alternative should be called an electrically qualified drop-in until VDS, VGS, RDS(on), current, SOA, thermal behavior, gate charge, pinout, lifecycle, and the application's fault cases have all been compared.

Table


PartCompatibilityEvidence and Qualification Notes
DMP3056L (Diodes Incorporated)Pin/package compatible candidate; electrically close, not pre-qualified as a drop-in.SOT-23 top view uses G at lower left, S at lower right, and D at the top, matching the common 1=G, 2=S, 3=D arrangement. The manufacturer offers DMP3056L-7 in 3,000-piece tape-and-reel and DMP3056L-13 in 10,000-piece tape-and-reel. Its manufacturer summary reports −30 V, −4.3 A and 50 mΩ max at −10 V, but those exact electrical claims were not machine-validated in this research pass; verify the linked datasheet before substitution.
Si2301CDS (Vishay Siliconix)Pin/package compatible but functional only; not a 30 V drop-in.TO-236/SOT-23 pinout is 1=G, 2=S, 3=D. It is rated only −20 V VDS and has 112 mΩ max RDS(on) at VGS = −4.5 V, ID = −2.8 A, so it is unsuitable wherever the AO3401A's 30 V rating or lower resistance is required.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary distributorsCheck the manufacturer's authorized distributor network and search DigiKey or Mouser; exact listings and authorized status for the selected seller remain unverified here. See the LCSC C15127 purchasing listing, checking manufacturer identity before purchase. Stock and pricing are time-sensitive.
PackagingTape-and-reel, cut tape, and distributor custom-reel availability must be confirmed for the actual orderable SKU. A 3,000-piece AOS full-reel quantity is unverified in this research; do not use it as a purchase commitment.
MOQNo universal MOQ applies. Distributor pages observed during research offered prototype quantities/cut tape, while full-reel orders use the reel quantity; exact MOQ is unverified and time-sensitive until checkout.
Sourcing adviceBuy the exact Alpha & Omega Semiconductor AO3401A manufacturer part when its specifications are required. Multiple unrelated manufacturers sell parts marked “AO3401A” with different datasheets; do not assume those are electrically identical. Verify manufacturer, datasheet revision, package marking, authorized-channel status, lifecycle, and reel traceability.
Sources
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources