Project Start Assistance


Thought for 7 mins 28 sec
Thought for 6 sec
1/4 Inspect live PCB checks and recover prior routing-repair findings.

Inspect live PCB checks and recover prior routing-repair findings.

Repair supported routing, redundant copper, and local blockers without changing board size.

Verify final connectivity and DRC; report any remaining fabrication blockers.

Add visible schematic wires when schematic geometry editing is available (blocked; outside PCB task).

Thought for 15 sec
Thought for 5 sec
Awaiting 1 task
"USB-C Routing Cleanup" completed.
I checked the PCB and attempted local repairs, but no improvement could be safely retained; unsuccessful changes were reverted. Fresh DRC confirms 9 airwires remain—six USB data, two ground, and one output VBUS—plus 11 protected floating/redundant copper nodes, with zero copper overlaps.
The main blocker is stale USB-C breakout copper that the available recovery operation cannot replace, so the board is not fabrication-ready; this needs Contact Support before further USB routing. Exact findings are in the PCB Routing Repair Report.

Get Free Expert Help

We want to get the prototype into your hands fast. Speak with one of Flux's in-house electrical engineers to review your project.

Collins, Flux electrical engineer
Ryan, Flux electrical engineer
Nico, Flux electrical engineer

Collins, Ryan, Nico — real humans who've shipped real hardware


Waiting for input


PCBWay Manufacturing Readiness
Verdict
FAIL — do not submit this revision for PCBWay fabrication or assembly.
The latest independent review confirms 28 unrouted connections and 3 different-net copper overlaps. Protected stale USB-C breakout copper prevents the affected J2 USB escape routing from being safely deleted and regenerated with the current layout operations.
Work Completed
  • Applied a four-layer PCBWay-oriented stackup with 35 µm copper.
  • Moved R19 to restore pad escape clearance.
  • Removed all deletable redundant and floating stale copper found by the repair pass.
  • Reduced airwires from 30 to 28.
  • Re-ran live DRC and an independent manufacturing-readiness review.
Manufacturing Checklist

Table


ItemStatusEvidence / release requirement
All nets routedFAIL28 airwires remain: 25 GND, 1 HOST_VBUS_RAW, 1 OUTPUT_VBUS, and 1 UP_USB_DM.
Different-net copper overlapsFAIL3 overlaps remain around protected UP_USB_DP routing and J2 VBUS/GND pads.
Copper fills regeneratedBLOCKEDFinal repour cannot be certified while protected obsolete USB copper and unrouted GND connections remain.
Floating copper islandsBLOCKEDDeletable stale islands were removed, but zero floating islands cannot be certified after a valid final repour.
Continuous ground planeFAIL25 GND airwires remain; L2 also contains signal/power routing, so uninterrupted reference coverage is not demonstrated.
USB D+/D- routingFAILUP_USB_DM is disconnected at J2; UP_USB_DP contains protected copper shorts.
USB pair mismatchBLOCKEDNo valid completed endpoint-to-endpoint pair exists, so mismatch cannot be meaningfully measured. Target after repair: 90 ohm differential intent and <=2 mm mismatch.
VBUS copper for 2 A continuousFAILEXT_VBUS_RAW and OUTPUT_VBUS include 0.15 mm traces; SELECTED_5V includes 0.254 mm traces. These are not accepted as a demonstrated 2 A continuous path on 1 oz copper.
VBUS via capacityBLOCKEDExisting 0.6 mm pad / 0.3 mm drill vias lack a validated parallel-via/current-density calculation. Use multiple appropriately plated vias at layer transitions.
Spacing around U1/U2/power/USBPARTIALR19 pad access was corrected, but final assembly/debug spacing cannot be signed off while J2 routing must be rebuilt.
Mounting-hole keepoutsBLOCKEDDedicated mounting-hole components and screw/washer copper keepouts were not identified in the live review.
Silkscreen clear of padsBLOCKEDCrowded labels remain visible around J2/C5 and upper-right circuitry; numerical clearance was not certified.
Board-edge clearanceBLOCKEDBoard is 50 x 40 mm with a configured 0.4 mm inset, but actual minimum copper/drill-to-edge clearance was not certified.
Generic passive MPNsOPEN FOR ASSEMBLY38 generic resistors/capacitors have no manufacturer part number. Bare-board fabrication is unaffected, but turnkey PCBA sourcing is incomplete.
Confirmed Layout Blocker
Two protected UP_USB_DP traces overlap J2 pads on other nets:
  • ...Trace.a917968ed8486a430b5d7e140e273839 overlaps J2 VBUS__1 (HOST_VBUS_RAW).
  • ...Trace.d6a0d6ac907f52bef56557136f74faa4 overlaps J2 VBUS__1 and GND__1.
Additional obsolete protected breakout objects remain near x = +0.25 to +0.75 mm while J2 is centered near x = -12.59 mm, confirming retained breakout geometry from an earlier placement.
Required Release Sequence
  1. Remove or platform-reset the protected obsolete J2 USB breakout copper.
  2. Regenerate the J2 USB-C breakout at the connector's current position.
  3. Route UP_USB_DP/DM as a complete differential pair over an uninterrupted GND reference.
  4. Replace narrow 2 A VBUS segments with validated wide traces/pours and adequate parallel vias.
  5. Close all remaining GND and signal airwires.
  6. Repour all planes and verify zero floating islands.
  7. Run final DRC for airwires, shorts, clearances, edge spacing, keepouts, and silk-to-pad overlap.
  8. Measure and record USB D+/D- electrical lengths and mismatch.
  9. Assign MPNs to generic passives if PCBWay assembly is required.
Release Decision
PCBWay fabrication readiness: NOT READY. Gerber/BOM/pick-and-place export is intentionally blocked until the release sequence passes.
  • Verdict

  • Work Completed

  • Manufacturing Checklist

  • Confirmed Layout Blocker

  • Required Release Sequence

  • Release Decision