Identifying SMD Component

irflashrex

irflashrex

IMG00012.jpg

Image

flux

That top mark “7002” on a 3‑pin SMD package is very likely a 2N7002 N‑channel MOSFET (SOT‑23), commonly used for small‑signal switching and level‑shifting.
How to verify quickly:
  • Gate will be the pin that’s isolated (very high resistance to the others).
  • In diode‑test mode you’ll read a body‑diode between the other two pins; the remaining pin is the gate. Typical pinout for 2N7002 is 1=Gate, 2=Source, 3=Drain (confirm with your board traces).
Want me to help pick a drop‑in replacement or check how it’s used in your circuit?
Find low-Rds MOSFET
Calculate gate capacitance
Select pull-down resistor
Query schematic nets
Verify drop-in replacement
Sign up to send
list all ESP-01 pins in a table format. For each pin provide its pin number, pin...
irflashrex

irflashrex

@copilot list all ESP-01 pins in a table format. For each pin provide its pin number, pin name and function.
1y

copilot

Here's a table listing the pins for the ESP-01 module, along with their pin numbers, names, and functions:

Table

Pin NumberPin NameFunction
1GNDGround
2IO2GPIO2, U1_TXD, I2C_SDA, 12SO_WS
3IO0GPIO0, HSPI_MISO, I2SI_DATA
4RXDGPIO3, I2SO_DATA
5TXDGPIO1
6ENChip Enabled Pin, Active High
7RSTReset Pin, Active Low
8VCCSupply Voltage
Would you like more details on any specific functionalities or application tips for these pins?
1y
irflashrex

irflashrex

do i need pin 2 to be high in normal operation?
1y

copilot

In normal operation, you typically want GPIO2 (Pin 2) on the ESP-01 module to be pulled high. This is generally important for successful booting when the ESP8266 is powered on or reset. Here are some details:
  • GPIO2: It should be connected to VCC (pulled high) for the ESP-01 to boot properly into the normal operating mode, also known as Flash mode.
Doing this ensures that the device doesn't enter a different boot mode, which could interfere with normal operations.
1y
irflashrex

irflashrex

do i need pin 3 to be high in normal operation?
1y

copilot

Yes, for normal operation of the ESP-01, you should also ensure that GPIO0 (Pin 3) is pulled high. Here’s why:
  • GPIO0: If GPIO0 is pulled high during power-up or reset, the ESP8266 boots into standard Flash mode, allowing the device to execute the firmware stored in its flash memory.
To enter the programming mode (to upload firmware), GPIO0 needs to be pulled low during reset. However, for regular operation, keeping it high ensures that the device boots correctly into normal operational mode.
1y
irflashrex

irflashrex

is there any resistance needed for pins 2 or 3?
1y

copilot

It's a good practice to use pull-up resistors to ensure that GPIO2 and GPIO0 are held high. A standard value for pull-up resistors in this context is typically around 10 kΩ. Here’s a bit more detail:
  • GPIO2 and GPIO0: Connect a 10 kΩ resistor between each GPIO pin and the VCC. This pull-up resistor helps maintain the pin in a high state and prevents it from floating, which might lead to unpredictable behavior.
These pull-up resistors are especially useful during power-up and reset to ensure reliable operation. Feel free to adjust the resistor values based on your specific design requirements, such as power consumption or signal integrity.
1y
Someone is typing...
2
3.3vdc
CD
RS
er-cd
CS
reset
cd-dr
cs-rs
ER
rst
DR

No results...

Learn to Add a Component

[Example] ESP32 Reference Design

[Example] ESP32 Reference Design thumbnail
An example development and reference design for the ESP32 microcontroller.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor

Qty 1

Arrow

$1.59–$2.44

Digi-Key

$2.31–$3.87

LCSC

$2.28–$2.37

Mouser

$2.56

Verical

$0.79–$1.77

Controls