Tuya RS485 Probe Interface


I’ll finish the handoff by producing fully corrected BOM and pick-and-place files with the T1-U merged into them, instead of requiring the assembler to combine a separate addendum manually. I’ll also do one final visual orientation check against the live PCB.
Production handoff is complete.
  • Corrected BOM includes the U2 exactly once.
  • Corrected pick-and-place includes its verified position: X −27.0 mm, Y 4.93 mm, 0°, top.
  • Visual orientation check passed: sensor/RS-485 holes and AC-input holes remain at opposite board ends.
  • Routing remains complete with 0 airwires and 0 redundant traces.
Use these corrected files instead of the original exported BOM and placement file:
These should be submitted with the latest Gerber ZIP.

T1-U Migration Review
Completed schematic migration
U2 is now the exact published Tuya T1-U. This report supersedes the earlier stopped/incomplete checkpoint. The resumed seven-item schematic scope is complete; PCB placement, routing and fabrication qualification remain deferred.
Installed component
  • Part: Tuya T1-U
  • Part UID: 9c6c099d-9667-4f89-a14a-d2fbaa5014c9
  • Installed published version: 9d7124b3-6b27-4147-9074-df758194718c
  • Manufacturer: Tuya Smart; MPN: T1-U.
  • The lead/user confirmed independent source-part verification and publication before this resumed batch. Read-only consuming-schematic inspection confirms all 21 numbered pins and exact installed identity.
Scope status

Table


ItemStatusVerification
1. Replace U2 allowing footprint changeCompletedReplacement succeeded, preserving and verifying six net connections.
2. Map power/UART/direction/button netsCompletedExact pin/net table below independently read back.
3. Remove R11 and CBU_MODE after successCompletedR11 removed after successful replacement; CBU_MODE then deleted. Final summary:40 components,21 nets; no CBU part, CBU_MODE or CBU_RESET.
4. Mark all unused T1-U pins NCCompletedAll15 requested NC flags read back, including TX2 and CEN; no unused pin connected to a low strap.
5. Preserve four-hole J3 and R13CompletedJ3 remains original four-pin hole footprint; R13 remains10 kΩ with separate receiver/output nets. No fifth CEN hole.
6. Update roles and reviewCompletedU2/R13/J3 role details updated; ERC has0 Errors and3 pre-existing pin-metadata Warnings unrelated to migration.
7. Defer PCB placement/routingCompleted as a scope restrictionReplacement flagged placement required; no placement/routing tool invoked.
Final read-back mapping

Table


T1-U pinNameNet / destinations
143V33V3; buck L1 output, C11/C12 local bypass, shared rail bulk, J3 pin1
13GNDGND; J3 pin2
15TX1UART_TX_RS485 -> U3 DI and J3 pin4/programmer RX
16RX1UART_RX_RS485 -> R13 pin1 and J3 pin3/programmer TX
8P24RS485_DIR -> U3 DE, active-low RE and R3 pull-down
17P28PAIR_BTN -> SW1 pin1 and R4 pin2; R4 remains10 kΩ pull-up
Receiver isolation is exactly U3 RO -> RS485_RO_ISO -> R13 pin2, through10 kΩ to R13 pin1 -> UART_RX_RS485 -> T1-U RX1/J3 TX. There is no direct RO-to-programmer-TX connection bypassing R13. LED1 remains a rail indicator, independent of GPIO.
NC pins:1 P14,2 P16,3 P23,4 P22,5 ADC,6 RX2,7 TX2,9 P9,10 P26,11 P6,12 P8,18 CEN,19 P21,20 P17,21 P15. TX2 is intentionally floating for normal boot; CEN is unused with its internal pull-up.
Replacement behavior and placementRequired
The replacement initially refused the extra connected CBU CSN pin. Only U2:CSN was detached for preflight compatibility while R11 and CBU_MODE were retained. The immediate retry succeeded, then R11 and the obsolete net were removed. No invalid old-module state is left behind.
The successful tool response explicitly said to place U2 on the PCB, i.e. placementRequired was signaled. The response did not expose a literal JSON boolean, so this is reported from its explicit placement warning rather than an invented raw field. PCB placement was deliberately not performed under the schematic-only instruction. The old board routing and exports must not be treated as valid for this new module. Schematic position was preserved by atomic replacement; no separate schematic rearrangement was attempted in this resumed scope.
Review evidence
Final review at2026-09-20T05:56:40Z: Electrical Rule Checks0 Errors,3 Warnings. All migration-caused floating-pin and obsolete-single-pin-net findings are resolved. Remaining warnings:
  • D3 SM712 pins1/2/3 lack informative source-library pin metadata.
  • BR1 HD01 pin3 lacks informative source-library pin metadata.
  • D1 SMAJ24CA pins1/2 lack informative source-library pin metadata. These existed before migration; they are not claimed resolved or waived. No Error/Warning entries were returned for the requested schematic-legibility/passive/system categories. Component Review Checks do not run on this consuming board and their absence is not a pass. This is not PCB DRC or manufacturing signoff.
Retained qualifications
Local module bypass C11=100 nF,C12=10 µF and rail bulk C10=100 µF remain. Prior analytical budget established approximately519.4 mA bounded rail operating load with600 mA planning allowance versus the3 A buck; no hardware transient/thermal qualification is claimed.
Four-hole programmer order remains 3V3 G TX RX from programmer perspective. Use3.3 V logic, avoid simultaneous external/programmer and buck drive, and prevent UART back-power during full power-cycle flashing. Firmware/bench validation of the selected T1-U flashing utility remains necessary. The official UART guide's CEN hardware-recovery caveat and the wider design's hot-environment F1 margin remain recorded in Board Bring-Up Plan and Power Budget; neither changes this completed schematic mapping.
  • Completed schematic migration

  • Installed component

  • Scope status

  • Final read-back mapping

  • Replacement behavior and placementRequired

  • Review evidence

  • Retained qualifications