Project Start Conversation


I’ll strip the schematic to the Uno headers and LoRa subsystem only, remove all orphaned nets, update the project specification and power budget, then rerun ERC and legibility checks.
Thought for 3 mins 13 sec
Thought for 5 sec
1/4 Remove all sensor, monitoring, button, and LED circuitry

Remove all sensor, monitoring, button, and LED circuitry

Compact and verify the remaining Uno LoRa schematic

Update project metadata and files for LoRa-only scope

Run ERC and schematic legibility checks

Thought for 14 sec
Thought for 7 sec
Awaiting 1 background task
"Arduino LoRa Shield Cleanup" completed.
The cleanup executor completed and reduced the schematic from 38 to 14 components. The remaining parts are the four Uno headers, AMS1117-3.3 supply and capacitors, RYLR998 header, UART translation, and reset test point; sensor, PV/battery-monitoring, button, and LED parts were removed.
Still needs verification
  • Re-run ERC and schematic-legibility checks.
  • Confirm the extra nets are intentional unused-header/no-connect nets.
  • Verify the project specification and power budget were updated.
  • Rename/update the project description, which still references the removed sensors.
  • Present the revised schematic checkpoint.
Execution stopped because your ACUs ran out.

Waiting for input


Project Specification
Product
A 2-layer Arduino Uno R3 shield for a solar-powered crab-pot buoy sensor prototype. The Uno is powered separately from USB and supplies the shield’s 5 V and GND rails. The shield interfaces to external sensor modules and a 3.3 V LoRa UART module.
First-build scope
  • Complete shield schematic and PCB layout.
  • Standard Uno R3 shield outline and header locations.
  • JLCPCB-assembly-oriented BOM with verified LCSC numbers where available.
  • ERC/DRC review before manufacturing export.
  • External modules and probes connect through labelled headers or screw terminals.
  • Firmware and weatherproof enclosure are outside this first build.
Architecture and resolved engineering decisions
Power
  • Input: Arduino 5 V and GND header rails.
  • 3.3 V radio rail: AMS1117-3.3 in SOT-223, subject to datasheet and library verification.
  • LDO capacitors: 10 uF input, 22 uF output, with voltage rating and ESR selected to meet the regulator datasheet; 100 nF ceramic at the radio connector.
  • Known 3.3 V peak load: RYLR998 up to 140 mA.
  • Estimated LDO dissipation at peak: (5.0 V - 3.3 V) × 0.14 A = 0.238 W. Use a generous copper heat-spreading area on the regulator tab and verify temperature in prototype testing.
  • The exact 5 V budget remains dependent on the selected HX711, KY-038, ACS712 modules, DS18B20 probes, and Uno USB-source capability. Verify module currents before final BOM release.
LoRa radio
  • RYLR998 connector: 1 VDD, 2 NRST, 3 RXD, 4 TXD, 5 GND.
  • Uno pins: D11 transmits to RYLR998 RXD; D10 receives from RYLR998 TXD.
  • Replace the proposed two-channel BSS138 bidirectional shifter. The AN10441 MOSFET circuit is intended for open-drain buses and is not the preferred interface for push-pull UART.
  • Use a unidirectional 5 V-to-3.3 V translator or resistor divider on Uno D11 → radio RXD. Connect radio TXD → Uno D10 directly only after confirming the ATmega328P input-high threshold and RYLR998 output levels from authoritative datasheets; otherwise use a proper buffer.
  • NRST uses the module’s internal pull-up and receives a labelled test pad.
  • Place the module at the board edge. Create a copper/component/via keepout beneath and in front of the antenna region using the module manufacturer’s dimensions.
HX711 tension sensor
  • Use a 4-pin control header: 5 V, GND, DOUT/D4, SCK/D5.
  • Add a separate 4-pin load-cell-side interface on the shield: E+, E-, A+, A-.
  • The chosen HX711 breakout footprint must expose matching E+, E-, A+, A- contacts so the shield terminal can route to the module. A generic four-pin MCU-only HX711 header is insufficient. Select and verify one specific module geometry before layout.
Sound sensor
  • KY-038 header: 5 V, GND, AO/A3, DO/D3.
Temperature probes
  • Three parallel 3-pin terminals: 5 V, DATA, GND.
  • Shared DATA net connects to D2 and one 4.7 kΩ pull-up to 5 V.
  • D2 is retained because no listed interface conflicts with it.
Voltage monitoring
  • Two inputs: PV+ and BATT+, each referenced to common GND.
  • Revise each divider to 56 kΩ top / 10 kΩ bottom, 1%, giving approximately 4.24 V at 28 V and preserving ADC headroom for resistor tolerance and rail variation.
  • Add 100 nF from each ADC node to GND.
  • Add a 1 kΩ series resistor between each divider/filter node and the Arduino ADC pin.
  • Do not use a 5.1 V zener as the primary ADC clamp. Prefer low-leakage Schottky clamps to GND and 5 V, or a verified dedicated protection arrangement, while checking injection current and back-powering behavior.
  • PV monitor → A0; battery monitor → A1.
Battery current
  • ACS712-05B module high-current path remains entirely off-board.
  • Signal header: 5 V, GND, OUT/A2.
User interface
  • TEST EVENT tactile button: D6 to GND; firmware enables the internal pull-up.
  • TX LED: D7 through 1 kΩ series resistor.
Pin allocation

Table


Uno pinFunction
A0PV voltage
A1Battery voltage
A2ACS712 output
A3Sound analog output
D2DS18B20 1-Wire
D3Sound digital output
D4HX711 DOUT
D5HX711 SCK
D6Test button
D7TX LED
D10LoRa receive from RYLR998 TXD
D11LoRa transmit to RYLR998 RXD
D0/D1Reserved for USB serial debugging
PCB requirements
  • Standard Arduino Uno R3 shield outline and header positions, sourced from an authoritative mechanical drawing or verified open-source footprint.
  • Two copper layers.
  • Ground pours on both layers with stitching vias, except the LoRa antenna keepout.
  • Keep LoRa and its antenna away from voltage-divider inputs and HX711 analog paths.
  • Place decoupling and regulator capacitors adjacent to their associated pins.
  • Size the 3.3 V path for at least 140 mA with margin.
  • Clear silkscreen labels for every external connector and pin; include polarity and signal order.
  • Use JLCPCB basic/extended parts where practical. Every final LCSC number must be checked against current availability before release.
Verification gates
  1. Verify RYLR998 pinout, supply limits, UART thresholds, antenna keepout, and peak current from its datasheet.
  2. Select one HX711 module and verify both electrical pinout and physical header spacing.
  3. Verify Uno R3 outline/header geometry.
  4. Complete the 5 V and 3.3 V worst-case power budget.
  5. Check ADC range and clamp currents across resistor tolerances and plausible 5 V rail variation.
  6. Run schematic ERC and resolve or justify every error.
  7. Confirm placement before routing.
  8. Run PCB DRC, verify zero airwires, and inspect antenna keepout and silkscreen.
  9. Generate BOM and pick-and-place data with current LCSC/JLCPCB availability.
Schematic checkpoint selections
  • Radio regulator: AMS1117-3.3, SOT-223, with 10 uF input tantalum, 22 uF output tantalum, and 100 nF at the RYLR998 socket.
  • Radio receive translator: 74AHCT1G125W5-7 (LCSC C842287), 5 V powered, active-low OE tied to GND.
  • Radio transmit divider: 10 kΩ top / 20 kΩ bottom, 1%, from Uno D11 to RYLR998 RXD.
  • ADC clamps: BAT54S-TP series Schottky pairs, with explicit warning that energized monitor inputs can back-power an unpowered Uno 5 V rail.
  • HX711 dependency: the schematic provides separate 4-pin control and 4-pin load-cell headers compatible with the Soldered 333005-class electrical interface. Exact dual-header spacing and the omitted optional B channel remain a PCB-stage mechanical dependency.
  • Uno header dependency: J1 and J3 use verified Harwin female 1x8 sockets. J2/J4 are currently logical numeric 1x6/1x10 symbols because verified stackable female variants were unavailable in the Flux library; replace them with Harwin M20-7820642 and M20-7821042-equivalent footprints before board setup.
  • Detailed current assumptions and release gates are recorded in the Power Budget file.
Open risks
  • Uno USB current availability depends on the source, cable, Uno revision, and connected loads.
  • Off-the-shelf HX711 and KY-038 modules vary in pin order and physical dimensions.
  • This shield is not itself weatherproof; marine deployment requires a sealed enclosure, corrosion-resistant connectors, strain relief, and condensation management.
  • Product

  • First-build scope

  • Architecture and resolved engineering decisions

  • Power

  • LoRa radio

  • HX711 tension sensor

  • Sound sensor

  • Temperature probes

  • Voltage monitoring

  • Battery current

  • User interface

  • Pin allocation

  • PCB requirements

  • Verification gates

  • Schematic checkpoint selections

  • Open risks