Project Start Conversation


I’ll strip the schematic to the Uno headers and LoRa subsystem only, remove all orphaned nets, update the project specification and power budget, then rerun ERC and legibility checks.
Thought for 3 mins 13 sec
Thought for 5 sec
1/4 Remove all sensor, monitoring, button, and LED circuitry

Remove all sensor, monitoring, button, and LED circuitry

Compact and verify the remaining Uno LoRa schematic

Update project metadata and files for LoRa-only scope

Run ERC and schematic legibility checks

Thought for 14 sec
Thought for 7 sec
Awaiting 1 background task
"Arduino LoRa Shield Cleanup" completed.
The cleanup executor completed and reduced the schematic from 38 to 14 components. The remaining parts are the four Uno headers, AMS1117-3.3 supply and capacitors, RYLR998 header, UART translation, and reset test point; sensor, PV/battery-monitoring, button, and LED parts were removed.
Still needs verification
  • Re-run ERC and schematic-legibility checks.
  • Confirm the extra nets are intentional unused-header/no-connect nets.
  • Verify the project specification and power budget were updated.
  • Rename/update the project description, which still references the removed sensors.
  • Present the revised schematic checkpoint.
Execution stopped because your ACUs ran out.

Waiting for input


Power Budget
Scope and method
The shield is powered from the Arduino Uno 5 V and GND headers. Linear-regulator input current is treated as approximately equal to its 3.3 V load current, plus regulator ground current. Module currents that vary by breakout implementation are marked Estimated and intentionally conservative.
3.3 V rail
The RYLR998 supply range is 2.3–3.6 V, with 140 mA transmit current at +22 dBm.

Table


LoadTypical / activePeakStatus
RYLR998 receive / transmit17.5 mA140 mADatasheet-backed peak
AMS1117 ground current8 mA10 mAConservative estimate from family/library data
3.3 V branch reflected to 5 V25.5 mA150 mALDO input current approximation
At the 140 mA radio peak, regulator dissipation is (5.0 V - 3.3 V) × 0.140 A = 0.238 W. The SOT-223 tab must receive generous copper heat spreading in the later PCB stage.
Direct 5 V loads

Table


LoadTypical / activePeak usedBasis
HX711 breakout plus indicator LED5 mA20 mAEstimated; bare HX711 is much lower, but breakout variants differ
KY-038 sound module10 mA20 mAEstimated; comparator, microphone amplifier, and LEDs vary
ACS712-05B signal module10 mA15 mAConservative module estimate
Three DS18B20 probes4.5 mA4.5 mA1.5 mA active per probe assumption
74AHCT1G125 UART buffer<0.1 mA static1 mAConservative logic allowance
TX LED with 1 kΩduty-dependent3 mAAbout 3 mA when on
1-Wire 4.7 kΩ pull-upduty-dependent1.06 mAWorst case while DATA is held low
Direct 5 V subtotalabout 30 mA64.6 mAEstimates noted above
The PV and battery dividers draw approximately 28 V / 66 kΩ = 0.424 mA each from their monitored external sources, not from the Uno 5 V rail under normal unclamped operation.
Totals

Table


ConditionShield current from Uno 5 V
Conservative active/receive estimateabout 56 mA
Simultaneous peak design estimate214.6 mA
Peak with 20% engineering margin258 mA
A typical Uno board load of roughly 40–60 mA would put the complete USB-powered system near 255–275 mA peak before margin, below a nominal 500 mA USB 2.0 budget. This is not a guarantee: Uno revision, USB source, cable loss, and actual breakout-module LEDs/regulators must be measured during bring-up.
Interface and protection checks
LoRa UART
The RYLR998 guarantees only VOH ≥ 0.8 × VDD; at 3.3 V that is 2.64 V, while a 5 V ATmega328P input is commonly specified with a 3.0 V minimum high threshold. Direct radio TXD to Uno D10 therefore lacks guaranteed margin. The selected 74AHCT1G125 accepts a high input from 2.0 V, runs at 4.5–5.5 V, and has active-low output enable.
For Uno D11 to radio RXD, the 10 kΩ / 20 kΩ divider produces 3.33 V nominal. With 5.25 V input and 1% worst-case resistor ratio it remains about 3.52 V, below the radio's 3.6 V maximum supply/input domain; with 4.75 V input and the opposite tolerance extreme it remains about 3.15 V, above the radio's worst-case 0.8 × 3.6 V = 2.88 V input-high requirement.
Voltage-monitor range
Each 56 kΩ / 10 kΩ divider produces 4.242 V at 28 V nominal. With 1% worst-case tolerance (56 kΩ low, 10 kΩ high), the ADC-side divider node is about 4.315 V, retaining headroom below a 5 V ADC reference. The 100 nF capacitor sees approximately 56 kΩ || 10 kΩ = 8.49 kΩ, giving a time constant of about 0.85 ms and a corner near 188 Hz.
Each BAT54S is wired with pin 1 to GND, pin 3 to the divider node, and pin 2 to 5 V, matching the verified series-diode topology. Maximum specified reverse leakage is 2 µA at 25 V.
Sequencing limitation: if PV or battery voltage is present while the Uno 5 V rail is off, the upper Schottky diode can source roughly 0.5 mA per 28 V input into the unpowered 5 V rail through the 56 kΩ resistor. Firmware cannot prevent this. The prototype must either avoid that power sequence, disconnect monitor inputs during servicing, or replace the rail clamps with a power-off-protected dedicated analog protector in a future revision.
Release gates
  • Measure the current of the exact HX711, KY-038, ACS712, and DS18B20 hardware variants.
  • Confirm the Uno USB source and cable can sustain the measured combined current without rail sag.
  • Thermally test U1 during repeated +22 dBm radio transmission.
  • Verify that PV/battery inputs cannot remain energized while the Uno is unpowered, or revise the clamp architecture before deployment.
  • Scope and method

  • 3.3 V rail

  • Direct 5 V loads

  • Totals

  • Interface and protection checks

  • LoRa UART

  • Voltage-monitor range

  • Release gates