Hardware Prototype Timeline


flux

The enclosure revision failed as a verification artifact, not necessarily because the overall v2c enclosure concept is wrong. The generated views were not reliable enough to prove that the selected parts, cables, and service motions physically fit, so I did not use them to authorize PCB changes.
What is resolved
The UI architecture is now clear:
  • The OLED and pushable encoder will share J9’s 3V3, GND, I2C_SDA, and I2C_SCL.
  • A smart I²C encoder avoids adding raw encoder A/B/push connections to the PCB.
  • The approved visual direction remains the screw-joined translucent enclosure with exposed controls, a guarded tube hatch, and a removable rear panel.
What remains unresolved
  1. OLED mounting
    • The candidate OLED PCB is about 29.2 × 26.7 mm.
    • The existing 36 × 24 mm opening is too large to retain it directly.
    • It therefore needs a carrier or bezel with verified screw locations, display alignment, panel thickness, and cable clearance.
    • That bezel would be visible, so it must be shown accurately before changing the detailed enclosure.
  2. Encoder mounting
    • The encoder electronics are suitable in principle, but the complete mechanical stack is not qualified.
    • We need to verify the threaded bushing, washers and nut, panel opening, 3 mm panel thickness, remaining shaft length, knob engagement, and push-button travel.
    • Without this, the knob might rub the panel, sit too far out, or lose its push function.
  3. Rear power inlet
    • A specific threaded panel-mount DC jack still needs to be fixed.
    • Its cutout, anti-rotation feature, nut clearance, solder-terminal depth, plug overmold, cable bend radius, and disconnect arrangement must fit the removable rear panel.
    • Rear-panel removal must not pull directly on solder joints or require cutting wires.
  4. Heater and thermal wiring
    • The heater block and tube holder are custom mechanical assemblies, not components already represented on the PCB.
    • The exact heater cartridge, block dimensions, thermal cutoff mounting, NTC packaging, thermocouple junction, strain relief, and thermal isolation still need qualification.
    • The proposed fine thermocouple wire is not directly compatible with the existing JST-XH contact range, which expects substantially larger conductors. A mechanically sound transition is required.
  5. Cable and service sweeps
    • We have not yet demonstrated that all plugs can be inserted and removed.
    • Cable bends must avoid the PCB, supports, hatch, optical chamber, and hot surfaces.
    • The rear panel must be removable with sufficient service slack.
    • The PCB/base assembly must remain removable without trapping the UI, power, heater, or sensor harnesses.
Why PCB routing is still on hold
The connector positions determine where the harnesses enter the enclosure and how much bend space they require. If one of those connectors needs to move after routing cleanup, the newly routed copper may need to be discarded.
Once those positions are mechanically frozen, I can make a surgical cleanup around U5, R9, R10, and D4 while preserving unrelated copper. That work will particularly address the wide HEATER_LOW_SIDE trace passing R10 with only about 0.36 mm local copper separation. It technically passes the present clearance rule, but it is poor margin in a noisy switching area.
So the current status is: the electrical UI strategy is selected, but the exact mounting and harness geometry are not yet proven. The PCB has deliberately been left unchanged until that proof is available.
what's the next step?

flux

The next step is to finish the mechanical harness package before touching PCB routing:
  1. Select exact OLED mounting hardware/bezel, encoder mounting stack, and panel-mount DC jack.
  2. Define the heater block, cartridge heater, thermal cutoff, NTC, thermocouple transition, connectors, and strain relief.
  3. Update the approved v2c enclosure with those exact geometries.
  4. Verify plug insertion, cable bends, rear-panel withdrawal, and base removal.
  5. Freeze connector positions.
  6. Then clean only the U5/R9/R10/D4 switching area and rerun DRC/airwire checks.
The immediate actionable item is exact part selection and dimensioned mechanical modeling for the UI, power inlet, and heater assembly.

Waiting for input


Thermal-Optical Test Rig Design
Purpose and boundary
Rev 1 bench carrier for characterizing one sealed 0.2 mL PCR tube, heater/block dynamics, block-to-liquid offset, and provisional color optics before the integrated reader schematic. It is research-use-only instrumentation and reports measurements only. The empty block preheats first, tube insertion is guarded and hot, and assay timing begins only after measured liquid equilibration.
Architecture
  • Input: certified 12 V, 3 A adapter at J1; F1 Littelfuse 02153.15MXEP 3.15 A time-lag fuse; D1 STPS5L25B series reverse-polarity diode; D2 SMBJ18A shunt TVS; C1 47 uF bulk.
  • Logic power: PS1 Traco TSR 1-2450, 12 V to 5 V/1 A. D3 Schottky feeds Pico VSYS so USB VBUS and the external supply are diode-ORed instead of shorted. Pico 3V3_OUT supplies sensors.
  • Controller/logging: U1 Raspberry Pi Pico SC0915. USB is used for programming and CSV logging. SW1 pulls RUN low; J10 exposes SWD.
  • Heater: protected 12 V passes through J3, whose external loop must contain the Therm-O-Disc G4A00091C physically in series, then through heater connector J2. Q1 IRLZ44NPBF switches the return low-side. U5 TC4420CPA drives Q1 at 5 V through R9; R10 defaults the gate off. D4 clamps drain transients.
  • Hardware guard: J4 is a normally-closed guard/lid loop. Opening it removes the 5 V logic-high from U4 input B; R6 pulls the node low. U4 SN74AHCT1G08 hardware-ANDs this state with MCU PWM, so firmware cannot force heat when the loop is open. R25 adds an independent 10 kΩ pull-down on HEATER_PWM_CMD, and R7/R8 divide the state to RP2040-safe INTERLOCK_MON.
  • Block temperature: J5 accepts a 10 kΩ NTC. R1 is a 10 kΩ, 0.1% high-side reference; R2 is 100 Ω and C6 filters THERM_ADC into U2 ADS1115 AIN0. ADS1115 address is grounded (0x48); the 100 Ω value stays well below TI's 1 kΩ source/filter-resistance guidance.
  • Liquid reference: J6 feeds U3 MAX31856 through matched 100 Ω series resistors R26/R27. C9 is 100 nF differential between the two IC-side filtered inputs; C10/C11 are 10 nF common-mode filters from the IC-side TC_PLUS_FILT/TC_MINUS_FILT nodes to ground. U3 BIAS is connected to connector-side TC_MINUS, before R27, while U3 T- remains on TC_MINUS_FILT; therefore R27 remains genuinely in series between the biased thermocouple lead and the filtered converter input. This channel validates, but never controls, the heater.
  • Optics: J7 is a provisional 3.3 V RGB/clear I2C breakout interface: pin 1 3V3, 2 GND, 3 SDA, 4 SCL, 5 INT. J8 is the LED fixture: pin 1 5V, 2 white return, 3 red return, 4 green return, 5 blue return, 6 GND/shield. Q2-Q5 independently switch channels and R20-R23 guarantee all emitters off at reset, enabling dark measurements.
Selected components and evidence
  • U1 SC0915: main header pin 39 is VSYS, pin 36 is 3V3, pin 30 is RUN; simultaneous USB/external powering uses a Schottky into VSYS rather than tying VBUS to VSYS.
  • PS1 TSR 1-2450: pin 1 Vin, 2 GND, 3 Vout; 6.5-36 V input, 5 V/1 A output.
  • U2 ADS1115: 2-5.5 V supply, AIN recommended within GND-to-VDD, ADDR=GND gives 0x48, and VDD requires local bypassing.
  • U3 MAX31856: 3.0-3.6 V. The corrected input network keeps R26/R27 in series, places C9/C10/C11 on the converter side, and connects BIAS to connector-side T-. Automatic open-circuit mode 01 tests once per 16 conversions and is intended for source resistance below 5 kΩ; firmware allows a 2.0 s startup qualification interval before reading and latching the fault register.
  • U5 TC4420: 4.5-18 V supply and VIH >=2.4 V, allowing a 3.3 V logic command; local 1 uF bypass is fitted.
  • Q1 IRLZ44N: 55 V MOSFET with maximum RDS(on) 25 mΩ at VGS=5 V. At 2 A, idealized conduction dissipation is about 0.10 W at that test value.
  • F1 02153.15MXEP is a 3.15 A time-lag fuse. Its production suitability remains conditional on measured continuous current, ambient/temperature rise, fault-clearing behavior, and nuisance-opening tests.
Power budget
Engineering sizing basis, not a measured result:

Table


LoadRailTypical/maximum planning value
Heater12 V1.5-1.7 A continuous, use 2.0 A design allowance
Pico module5 V input100 mA allowance
ADS1115 + MAX31856 + logic3.3/5 V<20 mA expected, 50 mA allowance
Optical sensor breakout3.3 V25 mA provisional
Four illumination channels5 Vonly one normally active; 15 mA each, 60 mA fault-case allowance
Gate driver/status/margin5 V50 mA allowance
5 V peak planning load is below 0.30 A. At 85% conversion efficiency this reflects to roughly 0.15 A at 12 V. Total expected input is about 1.85 A with a 1.7 A heater, and the design uses a 2.2 A rail allowance. F1 is now 3.15 A time-lag to tolerate normal heater operation, but both nuisance-opening and fault-clearing behavior must be qualified with the real harness and ambient range. PS1 has substantial margin at 1 A.
Interfaces and schematic reference map

Table


BlockReferencesImportant nets
Input/powerJ1, F1, D1, D2, C1, PS1, C212V_RAW, 12V_FUSED, 12V_PROTECTED, 5V_LOGIC
MCU/USB/debugU1, D3, C3, C4, SW1, LED1, J9, J10PICO_VSYS, 3V3, MCU_RUN_N, SWDIO, SWCLK
Heater/interlockJ2-J4, U4, U5, Q1, D4, R6-R10, R25, C12-C13HEATER_12V_AFTER_CUTOFF, HEATER_LOW_SIDE, HEATER_PWM_CMD, HEATER_GATE, INTERLOCK_OK_5V, INTERLOCK_MON
Block thermistorJ5, R1, R2, C5, C6, U2THERM_DIV, THERM_ADC, ADC_DRDY
Liquid referenceJ6, U3, R26-R27, C7-C11TC_PLUS, TC_MINUS, TC_PLUS_FILT, TC_MINUS_FILT, TC_SPI_*, TC_DRDY_N, TC_FAULT_N
OpticsJ7, J8, Q2-Q5, R12-R24I2C_SDA, I2C_SCL, OPT_INT, LED_*_CMD
Test pointsTP1-TP1012 V, 5 V, 3V3, GND, PWM, gate, thermistor, interlock, SDA, SCL
Fixture concept
Carrier stays on the bench. Replaceable harnesses lead to: heater/block assembly; physically mounted G4A00091C; normally-closed guard switch; embedded block NTC; disposable fine-wire thermocouple placement fixture; and an opaque optical head holding a sensor breakout plus selectable emitters. Use keyed housings, strain relief, heat-resistant wiring near the block, and labels at both cable ends.
Open risks and decisions
  1. G4A00091C sourcing and mounting qualification is open. Confirm genuine source, trip specification, electrical rating, crimp/termination method, thermal contact pressure, insulation, and one-shot qualification procedure.
  2. Optics are provisional. J7 assumes a 3.3 V I2C breakout with RGB/clear data and optional INT; starter firmware assumes a TCS34725-compatible module at 0x29. Confirm module voltage, pin order, pull-ups, spectral response, saturation, and geometry before integration.
  3. Verify J1/J2 terminal-block and J3 cutoff-harness temperature rise at 2 A; replace with a higher-current family if needed.
  4. Validate D2/D4 clamp waveforms with the real adapter/heater harness; the parts are general TVS devices, not heater-cable-qualified suppressors.
  5. Qualify F1 at maximum continuous heater current and worst-case ambient: record body/holder/connector temperature rise, repeated cold starts and PWM operation, nuisance-opening margin, and controlled downstream-fault clearing. Change rating or family only from measured evidence.
  6. The Pico library marks VBUS as an unconnected power input, but the physical module's onboard USB connector drives it internally. It is intentionally not tied to the carrier 5 V rail to prevent source contention.
  7. Firmware uses a configurable 90-minute engineering-default timeout measured from ARM; expiry latches heater-off. Experiments that require a different duration must change, document, and validate the constant rather than disabling the bound.
  8. No PCB layout has been started.
  • Purpose and boundary

  • Architecture

  • Selected components and evidence

  • Power budget

  • Interfaces and schematic reference map

  • Fixture concept

  • Open risks and decisions