# George wambugu **Handle:** @georgemars ## Stats - **Projects:** 7 - **Components:** 17 - **Followers:** 0 - **Following:** 0 ## More - [Starred Projects](https://www.flux.ai/georgemars/starred.md) ## Projects (Page 1 of 1, 19 total) - [SublayoutStm32f303](https://www.flux.ai/georgemars/sublayoutstm32f303.md) - stm32f303 with rf and barometric sensor Sublayout - [ultimate drone dev board](https://www.flux.ai/georgemars/ultimate-drone-dev-board.md) - drone board - [esp32 Sublayout with gps and Lora](https://www.flux.ai/georgemars/esp32-sublayout-with-gps-and-lora.md) - esp32 sublayout with gps and lora - [Stm32wb55eu6 with ble imu and sd card SUBLAYOUT](https://www.flux.ai/georgemars/stm32wb55eu6-with-ble-imu-and-sd-card-sublayout.md) - this is the stm32wb55eu6 board with a ble and 3d imu intergrated and sd card SUBLAYOUT - [NRF24L01 Sublayout](https://www.flux.ai/georgemars/nrf24l01-sublayout.md) - NRF24L01 Sublayout with antenna and impendence matching - [M24M02 EEPROMSublayout](https://www.flux.ai/georgemars/m24m02-eepromsublayout.md) - m24m02 EEPROM sublayout - [ESDS302DV](https://www.flux.ai/georgemars/esds302dv.md) - This is an esd protection device.. 2 channel bidirection with a breakdown voltage of 4.5 v and clamping voltage of 3v - [6v smd spdt](https://www.flux.ai/georgemars/6v-smd-spdt.md) - 6v smd spdt - [NSS12201LT1G 12v npn transistor](https://www.flux.ai/georgemars/nss12201lt1g-12v-npn-transistor.md) - SOT-23-3_1P4X3P040_ONS 12v npn transistor - [A2235-H gps ](https://www.flux.ai/georgemars/a2235-h-gps.md) - this is the gps a2235h - [DLF162500LT-5028A1](https://www.flux.ai/georgemars/dlf162500lt-5028a1.md) - DLF162500LT-5028A1 rf low pass filter - [LSM9DS0](https://www.flux.ai/georgemars/lsm9ds0.md) - this is an imu LGA-24_4X4X1_STM - [M24M02 EEPROM 2MB's](https://www.flux.ai/georgemars/m24m02-eeprom-2mbs.md) - this is an eeprom of an amaizing 2MB worth of storage space interfacing via i2c with the mcu - [5.5v tvs diode PESD5V0X1BCSF](https://www.flux.ai/georgemars/5p5v-tvs-diode-pesd5v0x1bcsf.md) - tvs diode clamping voltage of 5.5v breakdown 6v and operating voltage ya 5v - [barometric sensorENS220S-BLGT](https://www.flux.ai/georgemars/barometric-sensorens220s-blgt.md) - this is a barometric sensor based on the ens220 chip by sciosense - [spdt throw hole with model](https://www.flux.ai/georgemars/spdt-throw-hole-with-model.md) - this is a single pole dual throw switch with a angled through hole model - [female male header](https://www.flux.ai/georgemars/female-male-header.md) - 13pin male female header 2 rows - [STM32F303CCT6](https://www.flux.ai/georgemars/stm32f303cct6.md) - this is the stm32f303cctx series with arm based cortex m4 32b mcu +fpu , upto 256kbs of flash memory+48kbs of sram, 4adc, 2dac cloned from kicad - [STM32WB55EUXXX](https://www.flux.ai/georgemars/stm32wb55euxxx.md) - this is the esp32wb55euxx where x is just a place holder ## Pages - Pages: **1** --- *Generated from [https://www.flux.ai/georgemars](https://www.flux.ai/georgemars)*