Check and finish the imported board


Thought for 16 sec
Thought for 11 sec
Referenced guidance.
Create a file which documents ALL of the changes which we've made to the board . Every change since the initial KiCad drawing. It should be in Markdown
I’ll create a Markdown change history covering the work since the KiCad import, including reverted changes, accepted risks and the latest M4-hole/board-size changes. I’ll append the current manufacturing-rule values you requested, distinguishing verified settings from anything unspecified; no board edits.
Created Board Change History in your project files. It documents the recorded changes since the KiCad import—including connectors, routing, test pads, silkscreen, M4 holes and the 87 × 77 mm outline—and appends the manufacturing-rule values, marking unknown settings explicitly.
The file distinguishes applied changes, abandoned proposals and accepted risks, and flags the previous manufacturing ZIP as outdated. No schematic or PCB changes made.
"KiCad Board Change History" completed.
Created Board Change History in Markdown, covering recorded changes since the KiCad import, including connector consolidation, routing, test pads, silkscreen, accepted risks, and the latest M4 holes and 87 × 77 mm board expansion.
The appendix includes track width, clearance, via/drill sizes, solder-mask expansion and board-edge clearance. Paste expansion and explicit minimum via-size settings are marked unknown, rather than assumed. The history is reconstructed from saved records and live inspection—not a guaranteed exhaustive commit-by-commit diff.
No board changes were made. The previous manufacturing ZIP remains outdated following the hole and outline changes; fresh verification and exports are still needed.
Execution stopped because your ACUs ran out.

Phase 6 preparation handoff
ARCHIVED / SUPERSEDED — 2026-10-22. Historical evidence only. Phase 6 is CLOSED (original SMD Pico retained; optional extra grounds are NOT blockers; antenna compromise accepted; no RF rework). Phase 7 is also closed. Resume/next-session instructions below are not active. Current status: Import Review and Plan — authoritative status.
Session outcome
Read the latest import-review-and-plan and audited the live board. No schematic, PCB, net, placement, drill, rule or property changes were made. This preparation audit is not Phase 6 completion, routing completion or fabrication approval. Execution stopped when ACUs ran out, before updating the main plan or reading back this handoff.
Assigned-scope status

Table


ItemStatusEvidence / blocker
Read latest plan and proceduresCompletedPhase 5 closed with deferrals; Phase 6 separately authorized.
Live routing and ground auditCompleted16 components, 18 nets; 85 × 75 mm two-layer board; 73 route segments, 24 smart vias, 91 pads; one persisted Polygon with generated Fill.
Research Pico 2 W antenna geometryCompleted as qualified proposalOfficial datasheet establishes 14 × 9 mm cutout guidance; precise proposed offsets below come from an installed open-source footprint, not manufacturer tolerances.
Repair missing U1 ground terminals in placeUnattempted; blockedNo safe native operation was established for creating missing terminals and rebinding existing imported Mount pads while preserving identities and routes. Do not replace/rebuild U1 or route Mount pads without authorization.
Apply RF geometry / pour changesUnattempted; approval requiredNo cutout, keepout, component move or copper change applied.
Update main plan and verify written reportUnattemptedACUs exhausted. This separate handoff preserves findings without overwriting unread plan content.
Fresh read-only checks
Selected fresh checks at 2026-10-21T02:52:59.417Z reported 15 airwires, one via-in-pad and four Missing Power errors. Requested physical categories otherwise passed: no overlapping/floating copper, redundant traces, invalid pads/layers, missing footprints, body overlaps, outside-board, pad-access or keepout findings. No existing RF keepout means zero keepout findings does not validate antenna clearance.
Live routing state and fresh checks both report zero redundant-trace groups, versus historical plan count of four. Nothing was deleted in this session; cause of the difference was not established.
Ground-mapping prerequisite
U1 UID c0e7db64-469e-4d80-9f56-c3559d681d10, part UID b7ae219c-ee57-4ebe-aa68-4a42e3af2283, part version fc54f858-9b25-4708-a293-3515a8645b2a. Nine electrical terminals remain: GP0/1/2/4/5/6 (physical pins 1/2/4/6/7/9), GND3, 3V3_36, VSYS39. Other ground positions remain Mount pads with blank effective net IDs. /GND still has ten electrical pins and only one U1 terminal.
At U1 origin (24.665, 10.075) mm, 0°, Top, missing ground-pad world centres are:

Table


Physical pinX mmY mm
GND814.97516.425
GND1314.9753.725
GND1814.975-8.975
GND2334.355-8.975
GND2834.3553.725
GND3834.35529.125
AGND3334.35516.425
Existing-pin connections and adding pads bound to existing terminals do not establish a safe missing-terminal repair. Ground routing remains gated. Keep this distinct from D2 A1/A2 naming cleanup deferred to Phase 11. Prior plan includes ground/AGND identification evidence.
RF proposal — not applied
Official source: Pico 2 W datasheet, section 2.2.1 and Figure 7. It specifies a 14 × 9 mm antenna cutout, warns nearby material reduces antenna effectiveness, and recommends board-edge placement. Copper-only exclusion is not equivalent to a substrate cutout.
  • commentFileId-fd3ca91f1109ba4f9ccb22a9c3b964a39c3d88423184fc7c8aa3506733eff98a

    Official page 11 rendering / keepout text
  • commentFileId-7972cf80cdaf9d7e5205ba79f9d28b27bad6370e50648f354fc06c6335a0a143

    Official page 12 rendering / Figure 7
  • Exact installed KiCad source footprint
The installed RaspberryPi_Pico_W_SMD_HandSolder.kicad_mod explicitly says it supports Pico 2 W. Package version 10.0.7~ubuntu24.04.1; SHA256 4f2a2baf753d79689a9f70675a8c42f6d0c6253296df0e2d202917b3d074e682. Public repository retrieval did not locate this installed file; use the exported source as the exact evidence, not a claim about repository HEAD.
Source nominal board-clearance suggestion: local KiCad x ±7.1 mm, y 17…26 mm. Converting KiCad Y-down to live Y-up at the existing U1 pose yields a 14.2 × 9 mm rectangle x 17.565…31.765, y -15.925…-6.925 mm. This is a qualified open-source nominal proposal, not a manufacturer-toleranced coordinate claim. The library also has a shaped antenna copper exclusion within this rectangle.
Its broader RF copper exclusion is local x ±21, KiCad y 25…35 mm: live world x 3.665…45.665, y -24.925…-14.925 mm, clipped at board x 42.5 mm. Any approved implementation must check actual geometry and both copper layers, including generated copper.
An internal slot preserves the outer rectangle but the inspected outline schema did not establish hole support. An edge-connected notch would extend the 14.2 mm-wide region to board bottom y -37.5 mm, requiring explicit outline-change approval. Neither alternative was selected or applied. Do not silently change U1 placement or treat a copper-only keepout as equivalent.
Existing ground copper
/GND UID db4fc101-97ce-41ea-a68a-b18d44bf8b9b; Polygon UID 821340a4-4da0-41a5-8391-3be8a3819f85, with generated .fill child. Persisted rules show Bottom connected layer, 0.2 mm clearance; boundary spans x ±42, y ±37 mm. SVG shows copper covering the proposed antenna area.
No closed-outline route-segment fill pieces were found, so the static trace-fill migration prerequisite was absent. A persisted Polygon plus generated Fill is not by itself proof that migration is needed or that all dynamic exclusions work. Retain existing nodes until RF choice is approved; any conversion must be reversible and compare connectivity and resulting copper. No migration was applied.
Via-in-pad proposal — not applied
3V3 smart via 587ac117-fc20-472e-943f-1bb3241bb67f is at (35.675, 24.045) mm, generated suffix .imported-via-0.0-0. U1 pad36 centre is (34.355, 24.045) with 3.2 × 1.6 mm copper, right edge x35.955; via copper radius is 0.3 mm. A candidate x ≥36.455 provides 0.2 mm copper gap, with a short escape. Validate surrounding geometry and approval before committing; nothing moved.
Fifteen live airwires
These are the observed worklist, not new routes:

Table


NetAirwire endpoints
/5VU4:+OUT → D3:A
/12V_SW (4)Trace2951 → Trace a6c9; D2:A1 → Trace ac86; U4:+IN → Trace84be; U4:+IN → J3:Pin_2
/GNDTrace7a38 → D2:A2
/K1 (2)Trace163e → J4:Pin_1; J4:Pin_2 → J4:Pin_1
/K2 (2)J5:Pin_2 → Trace c41a; J5:Pin_2 → J5:Pin_1
/LI1U2:LI → J4:Pin_3
/LI2J5:Pin_3 → U3:LI
/LO2U3:LO → U1:GP6
/TX2U3:TX → U1:GP4
/VSYSD3:K → U1:VSYS
Trace annotations: 2951 = U3.VS/R2.2 island; a6c9/ac86/84be = U2.VS/R1.2 island; 7a38 = U2.GND escape; 163e = U2.K/R1.1 island; c41a = U3.K/R2.1 island. Bottom trace rule coordinates are mirrored relative to SVG world geometry: use SVG world coordinates for physical collision conclusions.
Preservation and remaining work
Preserved all 16 components, 18 nets, existing working copper, approved placements, stackup, U4 SMD geometry, prior U2/U3 IC classification, and prior D1/D3 cathode drill fixes. J3 assignment remains /SW_IN, /12V_SW, /12V_SW, /GND. Actual owned connector/holder/resistor/capacitor/TVS fit remains unresolved from Phase 4; no guessed dimensions or drill edits were made.
Next session: read this handoff and current main plan; establish a safe missing-terminal repair path; obtain the RF geometry decision; update Phase 6 status/log without erasing history; re-run live checks after any authorized edit and read back document changes. Main board remains unfinished and not ready to order.
Computer geometry-source was still running when execution stopped. Evidence files: /root/work/phase6/pico2w.pdf, pico2w.txt; /root/out/pico2w-page11.png, pico2w-page12.png, pico-w-source-footprint.kicad_mod. Stop the computer when safe. Internal feedback submission about missing-terminal repair capability failed; no ticket was filed.
  • Session outcome

  • Assigned-scope status

  • Fresh read-only checks

  • Ground-mapping prerequisite

  • RF proposal — not applied

  • Existing ground copper

  • Via-in-pad proposal — not applied

  • Fifteen live airwires

  • Preservation and remaining work