Project Start


READ-ONLY. Do not change anything. Short answer only.
Analyse the ESP32 auto-reset circuit around Q2, Q3, R15, R16 and the CH340G (U4).
  1. List the net on Base, Emitter and Collector of Q2 and Q3, and both ends of R15 and R16.
  2. The CH340G DTR# and RTS# outputs are active-low and sit at 3.3 V (high) whenever no host asserts them: on battery with no USB, with USB plugged in but no serial port open, and after esptool finishes. For that idle state, state the resulting level on ESP_EN and ESP_BOOT and whether the ESP32 (U1) is held in reset.
  3. Compare with the Espressif ESP32-DevKitC reference circuit, where each transistor's emitter is tied to the other control line (Q for EN: base from RTS#, emitter to DTR#; Q for IO0: base from DTR#, emitter to RTS#) so that both lines idle-high does nothing. State whether this board's circuit matches it or differs, and if it differs, which pins would need to change.

flux

Table


ComponentBase pin 1Emitter pin 2Collector pin 3
Q2Net 4, through R15 from DTR#GNDESP_BOOT
Q3Net 5, through R16 from RTS#GNDESP_EN

Table


ResistorPin 1Pin 2
R15 — 10 kΩCH340_DTR_N (U4 pin 13)Net 4 → Q2 base
R16 — 10 kΩCH340_RTS_N (U4 pin 14)Net 5 → Q3 base
With both outputs at 3.3 V as specified: both transistors turn on, pulling ESP_EN LOW and ESP_BOOT LOW; U1 is held in reset. This applies to each listed operating state if those outputs are actually high; active-low naming alone does not guarantee their startup/driver state.
This differs from the cross-coupled reference you describe. To match it, Q2 emitter pin 2 must change from GND to CH340_RTS_N, and Q3 emitter pin 2 from GND to CH340_DTR_N; bases, resistors and collectors stay as listed. Both-high would then leave both transistors off and allow EN/BOOT to pull high.
Read-only: nothing changed.
for this design, BT1 was not in the pick and place file, can you correct that?

flux

BT1 is now enabled for pick-and-place, and I regenerated the JLCPCB CPL file, available above. Only BT1’s export setting changed—no placement, footprint, routing or net changes.

BT1 Footprint Current Audit
Disposition — inspection completed, correction blocked by concurrent editing
2026-10-13. This audit concerns ONLY the installed Keystone 3034TR, not historical MPD or LOTES footprints. No PCB, schematic, sourcing, routing, footprint, or rule mutation was made by this audit. A fresh baseline was captured and analysed before considering edits. During that analysis, fatenerris manually changed routed copper, BT1 rotation, and BT1 position; the captured baseline is consequently no longer the current design. No attempt was made to undo or overwrite those edits. This project file is the only project mutation.
Confirmed baseline defects are board-owned stale BT1 silkscreen, not grossly incorrect library lands. The negative mark sits directly on the positive P2 solder land; stale outline strokes cross the central GND contact. The source footprint artwork is globally disabled on this board. Both solder feet already have paste; the existing N-only paste suppression already works in the actual exported Gerber. Correction must resume only after the manual edits settle, with a new exact baseline and pose-dependent silk plan. Do not manufacture these diagnostic files.
Authoritative source and independent dimension reading
Keystone K75 page 11 drawing, downloaded anew, SHA-256 5a36bc8eeca19f4ccc20a871d7db94bfba7a1f5e9004c6ac4444699ae65aa6a1. The applicable row is 3034/3034TR, FIG. 3 Ultra Low**, NOT a generic battery-holder drawing. The page does not contain a 3035 row.
The drawing's solder-land callouts are .050 [1.3] MIN width and .200 [5.1] MIN height; the central PCB negative contact is .156 [3.96] SQ. MIN. The 3034TR row gives A=.835 (21.2), H=.160 (4.1), L=.635 (16.1), W=.915 (23.1); these are catalogue values, not a land-centre pitch of 21.2 mm. The page says separate SMT negative contacts are not recommended for these ultra-low retainers; this does not mean the central PCB contact is omitted.
The citation-service answer did not resolve W extension-line endpoints, so those were independently inspected in the raster below rather than guessed. Direct visual observation, not citation-service-verified: W MIN spans the outside edges of the two solder lands; .050 dimensions a land's horizontal width, .200 its vertical height. With the inch values, W=.915 inch converts to 23.241 mm and land width=.050 inch converts to 1.270 mm; the resulting minimum-width nominal centre spacing is 21.971 mm. The actual library uses 21.970 mm, the customary two-decimal rounding (outer span 23.240 mm). The catalogue's 23.1 mm is not an exact conversion of .915 inch. No submicrometre correction or claim of tolerance-certified fit is made; these are nominal rounded lands, and the catalogue supplies no complete fabrication tolerance analysis.

pad-detail-bordered

The linked drawing does not explicitly prescribe stencil paste on/off. N no-paste is the assignment requirement and is corroborated by the exact library source, not invented as a drawing note.
Actual BOM and source part
Fresh BOM read: BT1 / Keystone / MPN 3034TR / LCSC C5213768, agreeing with intended sourcing. Attached BOM datasheet remains M65p9.pdf; this audit expressly used supplied K75p11.pdf.
Exact library part, UID c5169d52-f321-4b4d-b386-997f67ed59e4. Downloaded exact source footprint, SHA-256 42d365e796f544114d2115ec25211941ed390c08456496dea05e2495347a880a.
The source declares P1/P2 at X ±10.985 mm, size 1.27 × 5.08 mm, F.Cu/F.Paste/F.Mask; N at (0,0), size 3.96 × 3.96 mm, F.Cu/F.Mask WITHOUT F.Paste. It has no locating holes. Its nominal body artwork spans X ±10.605 mm and local Flux Y −8.7286 to +7.74146 mm, with notched/chamfered upper profile; the sides interrupt around the solder lands. This is library artwork rather than a new manufacturer-dimension extraction. A=.835 inch describes the body landmark, not centre-to-centre solder pitch. Native source artwork is inactive under existing board-wide suppression; no global rule was changed.
No new library-quality ticket filed: the downloaded source lands and no-paste declaration are correct nominally. The confirmed current problem is board-owned stale artwork. Historical report bt1-lotes-change-assessment explicitly says the previous Keystone import/export feedback submission failed and no support ticket was filed; no existing ticket number is available. The baseline local N rule works around that historical import/export layer issue successfully, so it was not duplicated or replaced.
Exact captured baseline
Element UID d5162a83-72e8-4e03-9e74-508a32f984de. Baseline native position (9.323,25.6387) mm, 0°, Top, not assumed from earlier claims. Footprint is FOOTPRINT_V5; symbol and connectivity were left untouched.

Table


FeatureSourced nominal targetCaptured actualAgent after-state
P1 local centre−10.985,0 mm (source nominal rounding)−10.985,0 mmNo edit
P2 local centre+10.985,0 mm+10.985,0 mmNo edit
P1/P2 copper shape and sizeRectangle, .050 × .200 inch = 1.270 × 5.080 mmRectangle, 1.27 × 5.08 mmNo edit; no gross dimension defect confirmed
Positive centre spacing / outside span21.971 / 23.241 mm inch conversion; source rounded 21.970 / 23.240 mm21.970 / 23.240 mmNo edit; nominal rounding limitation stated
N local centre and copper(0,0), 3.96 mm square source/contact callout(0,0), rectangular 3.96 × 3.96 mmNo edit
Mask openingExposed contact and both feetAll three fully exposed, 0 mm marginNo edit
Paste feet / NBoth feet present; N absentBoth feet present; N absent in actual GerberNo edit needed
Visible BT1 silkCurrent land-clear outline/polarityStale board-owned silhouette and misplaced negative markerUnattempted: concurrent edits block reliable correction
Positive P1 board centre (−1.662,25.6387), P2 (20.308,25.6387), N (9.323,25.6387) mm. Both positive pads resolve to RTC_VBAT net UID 0248a7a2-0162-4729-ad5f-dda60f76430d; N resolves to GND UID 4212a47e-ef0f-4e67-9caa-883f444ea8ef. Exported KiCad pad net names independently agree.
Pad node suffixes: P1 __be9bdaeb-0240-4715-a439-dae15a70a585, P2 __6ef2c7e8-bd8e-481c-adeb-b8e9ad8012dc, N __b381609f-74f0-4ebd-b94e-d70c3a7bb6bb (prefix is BT1 element UID above).
Existing ruleset dc735ab4-c5c7-47e6-b420-817e1471e6e6 selects ONLY N, setting solderPasteMaskExpansion: -1.98mm !important. KiCad export includes an N F.Paste layer flag but also −1.98 mm margin. The actual top paste Gerber, not that layer flag alone, establishes the absence of an aperture.
Baseline Gerber verification — passed no-paste; failed silk
Parsed actual native exports with gerbonara primitives and Shapely, using verified native→Gerber offset X +35.2300065255281, Y −52.5 mm (Gerber Y-up). Clip shape at each exact copper rectangle; minor last-decimal area deficits below are Gerber coordinate rounding, not covered mask strips.

Table


PadCopper area covered mm²Mask opening area covered mm²Actual paste intersection mm²Actual silk on pad mm²
P16.451597596.451597596.45159759 — present0
P26.451597826.451597596.45159759 — present0.14810417 — defect
N15.6816000015.681598120.00000000 — absent0.15604955 — defect
Total BT1-pocket silk on mask opening = 0.30415372 mm². This is a confirmed silkscreen/contact contamination issue even though the native checks do not list it. N-only paste verification: completed/pass. Feet retaining paste: completed/pass. Copper geometry nominal source match: completed/pass with catalogue rounding caveat. Silk: failed baseline, correction not applied.

before-local

Confirmed stale silk nodes and correction rationale
Fresh native rule-source read identifies:
  • 36b32505-9c37-47a2-b153-017fe893c88b, DFM BT1 negative: (20.2,26.6) mm, horizontal −0.4 to +0.4 mm, stroke 0.16 mm. It marks the current positive P2 pad as negative and overlaps its exposed solder land.
  • 711d7b30-c052-4cef-8956-99ca73f29376 and 74e2871c-60dd-43e7-aa0b-62efd78d9dec, DFM BT1 positive horizontal/vertical: (12.8,34.3) mm, 0.8 mm arms, 0.16 mm stroke. These remain at the former assembly artwork datum instead of following current BT1.
  • e9480535-ebed-47a0-9777-6d8939f40af9, DFM BT1 reference: (15.56,37.003) mm, 1.5 mm centred text, likewise board-owned rather than BT1-attached.
The exported pocket image confirms a stale outline at the former holder location, not the current library profile; its left-side strokes intersect N. Its exact editable asset/node ownership was not completely isolated before concurrent edits invalidated the correction baseline. Do not reactivate global artwork or remove a whole-board SVG blindly: that would affect other components. Safe next work: isolate those stale BT1-only silhouette segments in the existing board-owned artwork, suppress/remove only them, and replace them with the current source nominal outline clear of all mask openings; put '+' by the positive feet/top-cell orientation, and any '−' contact marker beside the central GND contact, never on an exposed pad. Outline/style are engineering implementation choices, not additional manufacturer land dimensions. If the integrated artwork cannot be isolated while preserving every unrelated shape, stop that specific item rather than replacing the whole asset without exact comparison.
Checks: exact baseline versus later concurrent state
These are not agent-before/agent-after mutation deltas, because no geometry correction was applied.

Table


Native checksBaseline 2026-10-13 16:12:02.795ZLater concurrent state 16:22:25.858Z
DRC Errors / Warnings1 / 43 / 9
Placement Errors / Warnings8 / 178 / 18
ERC Errors / Warnings0 / 10 / 1
Airwires13
Redundant-routing warning groups05
Baseline airwire: via node 3294850a-a0c5-4e52-a1b9-29d08b0172f0.throughHole.0-0 → BT1 P1. Later airwires: P2→P1 (RTC_VBAT), existing trace f5f1b064-d46c-47db-a871-069d7089a096→P1 (RTC_VBAT), generated GND stitch.81→N. None was routed or deleted by this audit.
Baseline DRC Warnings: L4 two pad overrides, U1 zone override, N paste override. Baseline Placement: U1 keepout Error, seven neckdown Errors (C26, C33, C35, C37, C4), twelve decoupling-loop Warnings and five neckdown Warnings. ERC: D4 unspecified-pin-type Warning. Later state adds five redundant-routing groups and BT1 outside-board Warning; all existing findings remain. No native copper-clearance/overlap Error was reported at either captured check. That does not erase the independent silk failure or certify manufacturing readiness. The off-board negative pad/feet must be treated as physical Errors if retained, regardless of current native Warning wording.
Preservation and concurrency evidence
Captured baseline exported inventory: 101 module/wrapper records, 66 nets, 1038 routed segments, 267 vias, four filled zones, 516 board graphics. These counts are from a native export, not a rebuilt board. Board 45 × 85 mm with 2 mm rounded corners; all original outline and holes were left untouched by this audit.
At later native inspection, BT1 bounds moved first to centre approximately (39.28,24.85) mm and then (38.85,24.53) mm, with footprint dimensions swapped to 20.5 × 23.74 mm, indicating rotation as well as displacement. These are rounded aggregate observations, not substituted for a final exact pose. History independently confirms manual fatenerris BT1 pose edits: #784cd5e7 (16:19:45), rotation #7327642d and position #f7c5b8c1 (16:19:50), position #05249738 (16:20:07). Pose/rotation diff affected this exact BT1 UID. Manual routing commits include #da9f6a01, #a43ef64b, #4a53e364, #f54fdb88 at 16:17–16:18.
Unaffected-geometry comparison: blocked/not run as an agent mutation comparison. There is no agent-applied footprint edit to compare. The user actively changed routing/pose while this audit was running, so claiming exact baseline=current or attributing changed pours/stitches to this audit would be false. No automatic-generation change was triggered by an agent geometry mutation; no unchanged-pour/via claim is made across the concurrent user edits.
Diagnostic artifacts — not manufacturing approval
No full-board external manufacturing audit, independent KiCad DRC, assembly placement CLI, or manufacturing approval was attempted. The required scoped native reviews and baseline aperture check were completed. These checks do not replace fabrication/assembly DFM.
Assigned-scope item status
Completed: required skills, independent authoritative drawing inspection, actual BOM/source lookup, exact baseline native pad/net/pose inspection, baseline native DRC/placement/ERC and export counts, diagnostic Gerbers, actual N paste absence with both feet retaining paste, identification of stale polarity/outline silk defects, concurrent-change evidence, this detailed project file.
Failed/blocked: correcting confirmed silk defects while preserving current pose and unrelated routing — concurrent manual changes invalidate baseline and pose-dependent replacement; precise ownership of stale integrated silhouette also needs isolation. Stable before/after unaffected-geometry comparison and post-correction acceptance therefore unavailable. No gross copper-pad defect was independently established that warrants guessed replacement.
Unattempted: all design geometry mutations, moving/rotating/restoring BT1, whole-footprint imports, unrelated routing repair, source-library modifications, post-correction manufacturing signoff. This concludes the inspection batch, NOT the overall correction task or PCB design. Resume after edits settle with a fresh exact baseline; retain the existing proven N-only paste rule unless later actual Gerbers show otherwise.
  • Disposition — inspection completed, correction blocked by concurrent editing

  • Authoritative source and independent dimension reading

  • Actual BOM and source part

  • Exact captured baseline

  • Baseline Gerber verification — passed no-paste; failed silk

  • Confirmed stale silk nodes and correction rationale

  • Checks: exact baseline versus later concurrent state

  • Preservation and concurrency evidence

  • Diagnostic artifacts — not manufacturing approval

  • Assigned-scope item status