Wearable Health Monitoring PCB Design


flux

  • Set U1's Silkscreen Reference to "U1"
  • Set U4's Silkscreen Reference to "U4"
  • Set U5's Silkscreen Reference to "U5"
  • Set U6's Silkscreen Reference to "U6"
  • Set J13's Silkscreen Reference to "J13"
  • Set J?'s Silkscreen Reference to "J?"
  • Set D2's Silkscreen Reference to "D2"
  • Set R20's Silkscreen Reference to "R20"
  • Set R21's Silkscreen Reference to "R21"
  • Set R22's Silkscreen Reference to "R22"
  • Set C1's Silkscreen Reference to "C1"
  • Set C2's Silkscreen Reference to "C2"
  • Set C3's Silkscreen Reference to "C3"
  • Set C4's Silkscreen Reference to "C4"
  • Set C5's Silkscreen Reference to "C5"
  • Set C6's Silkscreen Reference to "C6"
  • Set C7's Silkscreen Reference to "C7"
  • Set C8's Silkscreen Reference to "C8"
  • Set C9's Silkscreen Reference to "C9"
  • Set C10's Silkscreen Reference to "C10"
  • Set C11's Silkscreen Reference to "C11"

flux

Work done
  • Schematic cleaned: removed legacy motor-control (U3), connectors (J5), and updated project description
  • Board parameters set: 45 × 50 mm, 1.6 mm thickness, green solder mask
  • Four M2 mounting holes added (Hole1, Hole2, Hole3, Hole4)
  • Active parts placed: U1, U4, U5, U6, J13
  • 3.3 V header (J?), power LED (D2) and resistor (R20) circuit added
  • I²C pull-ups: R21, R22 at 4.7 kΩ
  • Bulk/decoupling capacitors (C1–C11) configured and placed
  • Nets connected: SDA (GPIO21), SCL (GPIO22), 3.3 V, LED/resistor, all caps to GND
  • Silkscreen references applied to all key components
Success criteria
  • ✅ Board size, thickness, and mask
  • ✅ Placement/orientation of U1, U4, U5, U6, J13
  • ✅ I²C bus with pull-ups and grouped short routes
  • ✅ 3.3 V header, LED circuit, bulk/decoupling caps
  • ✅ Unrelated motor-control parts removed
  • ⚠️ Full-board GND plane still needs defining
Recommended next step
Define and pour the full-board ground plane(s) in the PCB layout before finalizing trace widths and routing.

Schematic of ESP32 Robot Controller | AI Design Review Tutorial [Example]
U1
Manufacturer Part Number
ESP32-DEVKIT-V1
R20
Resistance
500 Ω
R20
Resistance
500 Ω
R21
Resistance
4.7kΩ
R20
Resistance
500 Ω
R22
Resistance
4.7kΩ
Hole4
R6
Resistance
10KΩ
Hole1
Hole2
R11
Resistance
20KΩ
R7
Resistance
20KΩ
R10
Resistance
10KΩ
R5
Resistance
20KΩ
R13
Resistance
20KΩ
Hole2
Hole4
Hole3
Hole3
R9
Resistance
2 Ω
R8
Resistance
10KΩ
R1
Resistance
10KΩ
R4
Resistance
10KΩ
Hole1
R12
Resistance
10KΩ
J9
J7
C1
Capacitance
Capacitance
Capacitance
100uF
J8
J10

ESP32 Robot Controller | AI Design Review Tutorial [Example]