TVS Diode D2 Overview


Below is a recommended set of components that you could use to design a DC‑DC Buck Converter circuit to convert +12 V to +5 V. One common approach is to use a switching regulator IC (such as the LM2596) along with its supporting passive components. See the table below:

Table


ComponentDescriptionSuggested Part/Link
Buck Converter ICA widely used switching regulator for step‑down (buck) conversion. It regulates the output voltage by switching an internal transistor at high frequency.LM2596
InductorThe inductor stores energy during the switching cycle. Typical values range between 33 µH to 100 µH depending on the design, load current, and frequency.33µH Inductor (or choose a value based on your design requirements)
Schottky DiodeProvides a fast recovery path for the inductor current during the off cycle with a low forward voltage drop.1N5822 (or another suitable Schottky diode rated for your expected current and voltage)
Input Capacitor(s)Helps reduce the input voltage ripple and filter out high‑frequency noise from the 12 V source. A combination of electrolytic (high capacitance) and ceramic (low ESR) is common.100µF Capacitor (add a ceramic capacitor in parallel to improve filtering)
Output Capacitor(s)Stabilizes the output voltage and minimizes voltage ripple on the 5 V rail. Low‑ESR capacitors are generally recommended.100µF Low ESR Capacitor (choose a value as specified by the regulator’s datasheet)
Implementation Notes
  • Design Considerations:
    • Check the LM2596 datasheet for typical application circuits. The datasheet will provide recommended values and additional guidance for improved performance (e.g., selecting the proper inductor and capacitance values based on load current and switching frequency).
    • Ensure that all parts are rated for the worst‑case conditions in your design.
  • Common Application:
    • This configuration is frequently used in designs where efficiency is paramount and where the power loss of an LDO would be excessive.
  • Schematic Integration:
    • Once the components are selected, you would place them in your schematic as a DC‑DC buck converter module. The converter’s output should be connected to your +5 V power net in your project, ensuring that it serves as the sole source (or is OR‑ed properly with any existing 5 V source to avoid contention).
You can use the links provided to search the Flux library for each component and add them to your project. If you need help with wiring the schematic for the buck converter or further tuning the supporting component values based on the regulator’s datasheet recommendations, let me know!
Select Buck Converter Parts
Verify Component Suitability
Alternative Search

Schematic of ESP32-WROOM-32E Reference Design
D2
GPIO36
D1
ESP_RX
CC1
GPIO18
USBDN
GPIO15
GPIO14
ESP_TX
GPIO21
USBDP
GPIO34
GPIO25
CC2
ESP_IO0
USBDN
ESP_IO0
GPIO22
GPIO16
GPIO5
USBDP
GPIO13
GPIO17
GPIO12
GPIO35
GPIO33
USBDN
ESP_RX
GPIO4
USBDN
USBDP
GPIO2
GPIO26
CC2
GPIO39
GPIO19
GPIO32
ESP_TX
ESP_EN
GPIO23
GPIO27
ESP_EN
USBDP
C4
Capacitance
10uF
+3V3
C3
Capacitance
10uF
VBUS
R1
Resistance
Resistance
Resistance
10kΩ
+3V3
C8
Capacitance
10uF
R2
Resistance
Resistance
Resistance
5.1kΩ
+3V3
C6
Capacitance
0.1uF
C7
Capacitance
0.1uF
R4
Resistance
1kΩ
R3
Resistance
Resistance
Resistance
5.1kΩ
+5V
+3V3
C2
Capacitance
0.1uF
C1
Capacitance
0.1uF
VBUS
+5V
+3V3
+3V3
+3V3
PWR
C9
Capacitance
10uF
USB1
Q1
U2
C5
Capacitance
10uF
Q2
U1
IC1

ESP32-WROOM-32E Reference Design