BÁO CÁO ĐỒ ÁN: MẠCH ĐẢO TÍN HIỆU SÁU KÊNH DÙNG IC 7404
Học phần: … Sinh viên/nhóm: … Mã sinh viên – lớp: … Giảng viên hướng dẫn: … Đơn vị: Trường Đại học PHENIKAA Ngày báo cáo: …
Phạm vi và tính trung thực của minh chứng: báo cáo được biên soạn từ yêu cầu và nhật ký thiết kế trong cuộc trao đổi. Chưa kiểm tra lại trực tiếp trạng thái dự án trong lần biên soạn này. Các kết quả kiểm tra phần mềm dưới đây là kết quả đã được ghi nhận trong nhật ký, không phải số đo phần cứng. Chưa có ảnh bo đã chế tạo, video vận hành hoặc dữ liệu đo thực nghiệm; những phần này được đánh dấu để bổ sung, không sử dụng số liệu giả định làm kết quả đo.
1. Nhiệm vụ và yêu cầu
Thiết kế mạch đảo tín hiệu dùng IC 7404 gồm sáu đầu vào và sáu đầu ra, sử dụng nguồn một chiề...
Tôi đã soạn Báo cáo đồ án mạch đảo sáu kênh dùng IC 7404, gồm đủ bốn phần: tìm hiểu tài liệu và tổng quan; học phần mềm; thiết kế và làm mạch; kết quả và xử lý dữ liệu thực nghiệm, kèm bảng nhiệm vụ, liên kết minh chứng và bảng ghi số liệu đo.
Báo cáo phân biệt rõ kết quả thiết kế đã được ghi nhận với phần chưa có đo đạc thực tế, không tự tạo số liệu; bạn cần bổ sung thông tin sinh viên, ảnh mạch, video và dữ liệu đo trước khi nộp chính thức.
Tôi đã đọc lại báo cáo và phát hiện một lỗi diễn đạt ở mục 5.3: ghi “ba cấu hình” nhưng liệt kê bốn trạng thái — toàn 0, toàn 1, 010101 và 101010.
Báo cáo còn thiếu minh chứng để nộp chính thức: tài liệu tham khảo mới dẫn tới trang chủ, chưa có sơ đồ/ảnh PCB và BOM đính kèm, chưa có số liệu đo thật; 3 lỗi và 2 cảnh báo tụ lọc chỉ là kết quả trong nhật ký, không phải kết quả kiểm tra hiện tại.
Tôi chưa sửa tài liệu hoặc thay đổi mạch trong lượt kiểm tra này.
Your and are available in the table tabs. Ask Flux to draw the schematic, or draw it yourself.
PCB Placement Report
Scope and disposition — 14 October 2026
Later routing checkpoint: placement unchanged; routing now complete with0airwires,0redundanttraces and0reportedblockingDRC/8cleanERCgroups (15:11:04.506UTC). Manufacturer-derived originalLEDpackage drawing resolved cathode-mark→negative and libraryK-left/A-right mapping beforedependentcopper. Switchorderingtable establishes2mmtravel,Vertical,frameH4.7mm;physicalactuatoraxis/projection/modelregistration remainsunqualified. See project file pcb-routing-report(gr);earlier“unrouted/polarityunresolved”statements belowarehistoricalplacement findings.
Completed: confirmed 50 mm width × 100 mm height rectangle and Standard 2 Layer stackup, set in one board call before placement.
Completed: explicit placement of all 46 components on Top, including every anchor, IC, capacitor and resistor; Bottom has no components.
Completed: 15 A/Y, ground-pin and supply-polarity silk labels; readable LED references; buffer references moved outside bodies; duplicate header references and annotation stars suppressed without deleting footprint nodes.
Completed: fresh layout readback, placement checks, copper/pad/layer checks and eight ERC groups. No topology, procurement metadata, values, pad geometry or authored routing changed.
Failed to fully verify: manufacturer-to-library LED polarity and switch actuator/model orientation. Nominal placement is usable, but physical qualification remains open.
Unattempted by scope: routing, trace deletion, fabrication exports/orders, new mounting holes, production qualification and manufacturer-profile metadata realignment.
Actual board and stackup
Rectangle centered at (0,0), x = ±25 mm and y = ±50 mm. Inventory: 46 elements, 46 footprints, 46 models, 168 pads and 38 nets. Footprint area 895 mm² / board area 5000 mm² = 17.9% fill. Top 46 components; Bottom 0.
Standard 2 Layer has Signal copper on both faces, each 35 µm (~1 oz), with a 1.499 mm FR-4/core dielectric, εr 4.3. Through-via template spans L1→L2, 0.6 mm pad / 0.3 mm drill; inherited manufacturing rules prefer 0.55 / 0.25 mm. No blind/buried/microvia technology was added. The wildcard laser-hole entry is a template capability, not an authored laser feature.
Warning — thickness/profile reconciliation: the readback calls totalThickness “1.50 mm” while its table includes a 1.499 mm core plus outer copper/coatings. Do not claim guaranteed finished thickness from that display. The intended fab target remains nominal 1.6 mm FR-4. Retained customized Standard Density rules are unchanged, but vendor-stackup metadata still says JLCPCB SDI 4 Layer, whereas the actual board is Standard 2 Layer. Align this metadata and finished thickness at the manufacturing checkpoint before ordering.
Existing GND pour remains enabled on All layers: Top 4573.072 mm² and Bottom 4715.638 mm², one island on each, with 18 automatically computed ordinary stitching vias. No authored route segments and no redundant traces. Bottom serves ground pour plus secondary signals, not a dedicated inner plane. Automatic pour/stitching recomputation is not routing completion.
Placement coverage (mm, board-centered, Y up)
Six rows indexed 1…6 have y = 30, 17, 4, −9, −22, −35 mm, a 13 mm pitch.
Table
Parts
X
Y
Rotation
SW1…SW6
−18
row Y
0°
LED1…LED6, input A indicators
−7
row Y
0°
LED7…LED12, output Y indicators
0
row Y
0°
R1…R6, pull-ups
−10
row Y + 3
0°
R7…R12, input LED resistors
−7
row Y − 3
0°
R13…R18, output LED resistors
0
row Y − 3
0°
U1 / C1
10 / 13
−2 / 5
0°
U2 / C2
10 / 17
18 / 22
0°
U3 / C3
10 / 17
−22 / −18
0°
J1 / C4
−4 / 3
44.8 / 40
180° / 0°
J2
22
25
270°
J3
22
−25
270°
Switch footprint envelopes leave about 1.775 mm left-edge margin and 7.92 mm between successive 5.08 mm-high envelopes. The actuator column is clear of other parts and connector cables. Exact actuator travel/projection is not qualified below.
Headers have a vertical long axis, pin 1 uppermost and pin 7 lowest. Pad transforms put J2 pin 7 at (22,17.38) and J3 pin 7 at (22,−32.62), both GND, with adjacent “7 GND” silk. Manufacturer drawing does not assign pin 1: library square pad and board net assignment are the datum, not manufacturer numbering approval.
J1 faces upward by its library edge rule and 180° rotation. Manufacturer supports insertion parallel to the PCB and 5.08 mm pin spacing. Pin 1 +5V is (−4,44.8), pin 2 GND is (−9.08,44.8); nearest pad-copper edge is 4.225 mm from the top edge. Its edge-offset point y=49.5 is within the allowed 0.5 mm tolerance.
Info — intentional connector envelope overhang: J1's coarse footprint/courtyard extends to y=50.55, 0.55 mm beyond the outline. No pad is off-board. Edge-rule connectors are exempt from body-overhang warnings and are checked by Edge Placement instead. Preserve this edge relationship; confirm actual body fit in final 3D/fab review rather than moving it inward and reintroducing an edge warning.
Decoupling measured at actual VCC pads
Reused connection-plan pin mapping: U1 VCC is pin 14; U2/U3 VCC is pin 20. Actual library VCC centers, transformed to the board, were measured; each capacitor P1 is +5V.
Table
Pair
VCC pad center
Capacitor center
Center→VCC
P1 pad→VCC
C1/U1
(12.475,1.81)
(13,5)
3.23 mm
3.20 mm
C2/U2
(13.429,20.925)
(17,22)
3.73 mm
3.00 mm
C3/U3
(13.429,−19.075)
(17,−18)
3.73 mm
3.00 mm
All meet the ≤4 mm 0603 target. C1 was moved above U1 to clear an offset 3D-body overlap. C4 P1 is about 7.87 mm from J1 pin 1. These are placement distances, not routed lengths or inductance guarantees. Next routing should feed VCC through the capacitors with short ground returns.
Fresh verification
14:00:58.599 UTC: Body Overlap, Components Outside Board, Pad Access Clearance, Edge Placement and Keepout reviews all Success, 0 errors / 0 warnings.
Same pass: Missing Footprints, Invalid Layers, Invalid Pads and Overlapping Copper all Success, 0 errors / 0 warnings.
Same pass: all eight ERC groups clean—floating pins, no-connect violations, single-pin nets, undriven nets, driver conflicts, pin-to-pin conflicts, missing power and shorted components.
13:59:08.120 UTC:79 airwire errors, expected before routing. Fresh routing-state also confirms 79 airwires and 0 redundant traces: +5V 19, A1…A6 24, Y1…Y6 12, LED driver/anode nets 24. Existing GND pour currently connects GND. Remedy: route the existing design at the next authorized checkpoint, not change the netlist here.
Neckdown Escape and Stackup Validation requests returned no named review or findings. Do not claim an independently executed numeric escape/thickness check; Pad Access Clearance passed and no neckdown move hint was returned.
Final targeted layout image confirmed U2 silk outside its body, no duplicate J2 label, and clear C2/header labels. Final silk clipping against routed copper is still an export-review step.
Physical qualification and existing warnings
LED — Warning: manufacturer-derived evidence confirms two 0.8 × 0.8 mm pads and 2.3 mm outer span. Library pads match those dimensions: centers ±0.75 mm, K left / A right, with a left silk dot. The query did not establish manufacturer polarity-mark-to-K correspondence. Before fabrication, inspect the original Lite-On package top/bottom drawing and tape orientation, correlate the K pad with the cathode mark, and check a sample by diode test. No polarity-changing mutation was made.
Switch — Warning: library pads are x=−2/0/+2 mm; common terminal 2 and GND/+5V assignments reuse verified electrical sources. Mechanical query did not yield validated actuator travel/projection claims. Library model has offset (19.5,−9.8,−21) mm and 90° X rotation, so its registration must be visually checked before mechanical sign-off. Verify actuator access and physical LOW/HIGH positions on a sample; no unsupported direction arrows were added.
Other pre-existing warnings outside this batch: provisional C4 effective-capacitance/rail-transient qualification, obsolete DM7404 procurement risk, and incomplete graphical schematic wire presentation. Values and procurement metadata were retained. These are not reported placement DRC blockers.
Next checkpoint
Qualify LED polarity and switch actuator/model registration; reconcile two-layer vendor metadata and finished thickness.
Route +5V and IC decoupling first, short GND returns, then A/Y and LED paths; preserve pin-7 ground labels.
Fresh DRC/ERC/airwire checks, final silk/copper and export verification, then bench rail and functional tests.
Assigned placement batch complete with zero reported placement blockers. Overall PCB remains unrouted and is not ready to fabricate.