PCB GND Repair


I’ll use horizontal entry and AWG 24–16 with those ratings as the provisional requirements, then check the remaining footprint and assembly details. PCB changes will stay on hold until NextPCB confirms sourcing and SMT acceptance.
Thought for 1 min 39 sec
Thought for 9 sec
Thought for 6 sec
Awaiting 1 task
revise the board with these ocmponents
I’ll prepare a separate SMT revision using the selected Phoenix terminals, preserving this release and every controller input. NextPCB acceptance will remain an open manufacturing gate, and I won’t create a footprint from guessed dimensions.
Thought for 2 mins 36 sec
Thought for 7 sec
Thought for 7 sec
Awaiting 1 task
"Pixel Board Manufacturing Readiness" completed.
The revision is blocked on the connector drawings—not your design choices. I confirmed the electrical pads, but couldn’t reliably obtain the mechanical-hole positions and pin-1 orientation, so I haven’t guessed footprints or changed the released board.
Please download and upload the PCB footprint/CAD file or dimensioned drilling-plan drawing for Phoenix 1824572 and 1824857, from each product’s “Downloads” or “3D view and CAD download” section. Those files will let me build the separate revision while preserving the controller connector and all input signals.
NextPCB sourcing and assembly acceptance also remain unconfirmed; the prepared enquiry covers both parts and the turnkey promotion requirements.

FR-4 Manufacturing and Partial Assembly Notes
Updated2026-10-09 after gate-drive redesign. NOT RELEASED. Current59-component/43-net schematic has30 newly added unplaced parts; old29-component routing is historical. No PCB edits or manufacturing exports were authorized in this wave. Conventional direct-mount2-layer FR-4 only; four identical100×55mm boards,nominal1.6mm,1oz each side,Top-side placement intent. See Gate Drive Redesign and Verification.
BOM and Assembly Split
All quantities exclude spares/attrition. Keep every part in master BOM; P&P exclusion does not suppress stencil apertures.

Table


DesignatorsExact MPNQty/boardQty fourAssembly
U1TI SN74AHCT244PWR14PCBA
Q1–Q7TI CSD19537Q3T728PCBA
C1Yageo CC0603KRX7R7BB10414PCBA
R1–R7Yageo RC1206FR-0710RL,10ohm728Manual
R8–R15Yageo RC1206FR-07100KL832Manual
J1Phoenix187552214Manual
J2TE284514-714Manual
J3MX2EDGR-5.08-02P-GN01-Cu-A14Manual
J4Phoenix188868714Manual
TP1Keystone495214Manual
Additional machine items:

Table


DesignatorsExact MPNQty/boardQty four
U2–U5UCC27524ADR416
U6TPS61040DBVR14
U7SN74AHCT1G04DCKR14
D1MCC B5819W14
L1Würth74404310014
R16–R22RC0603FR-0710KL728
R23RC0603FR-071KL14
R24RC0603FR-07931KL14
R25RC0603FR-07100KL14
C2–C6CC0603KRX7R9BB104520
C7–C12GRM31CR71E106MA12L624
C13CC0603JRNPO9BN10014
Current59/board,236 total;machine39/board,156 total;manual20/board,80 total. New devices are unplaced and need footprint/orientation/assembly review. C7–C12 effective capacitance remains an evidence/qualification gate. No live stock or assembler acceptance established. Wire,mates,strain relief and downstream splice are separate harness items.
Copper Footprint Corrections
The following describes preserved ORIGINAL layout corrections,not completion of the redesigned board. Driver loops,new gate/boost nets and decoupling placement must be implemented in the next authorized PCB wave.
Q1–Q7
Source: TI CSD19537Q3 datasheet SLPS549B, page9. Drawing rendered and visually inspected after machine extraction produced unsupported claims; use the drawing, not guessed earlier query dimensions.
Local coordinates before component rotation, mm:
  • Source1–3 and gate4: x=-0.975,-0.325,+0.325,+0.975; y=-1.435; pad0.500×0.630.
  • Drain5–8: x=+0.975,+0.325,-0.325,-0.975; actual y=+1.535,pad0.500×0.430. This overlaps exposed drain by0.020mm internally, retaining the TI external comb outline, whose tabs extend fromy1.340 toy1.750.
  • Drain exposed pad9: center(0,+0.390),2.450×1.900.
  • Pitch0.650; overall copper height3.500. Same-net overlap is intentional, not a short.
  • Exact UID selectors matched all seven pads per rule. A temporary14-airwire numerical edge-contact issue was repaired with internal overlap; final0 airwires.
  • Source/gate edge gap0.150mm is smaller than configured board minimum0.2mm. Native checks did not flag it; local clearance and mask-web capability still need fab sign-off. No global relaxation made.
U1
Source: TI SN74AHCT244 datasheet, PW0020A board/stencil drawing4220206/A02/2017. Corrected all20 pads to0.450×1.500mm,0.650mm pitch,5.800mm row spacing,R0.050 corners; pin mapping and90degree component placement retained. Local row coordinatesy=±2.900mm; ten columnsx=-2.925 through+2.925 in0.650mm increments. Same-size paste expansion0mm applied. Native routing remains complete after this change.
Stencil and Mask — Blocking
Do NOT manufacture the current Q paste layer as an approved stencil. Scalar paste expansion cannot reproduce TI's split exposed-pad windows. No speculative paste-only/copper geometry was added.
Require assembler-controlled stencil derived from TI page9: eight0.340×0.450mm apertures and two1.020×1.445mm exposed-pad windows,0.250mm central separation. Drawing gives0.225mm separation below drain apertures and0.750mm above source apertures, overall3.320mm span. Assembler must confirm stencil thickness, registration, paste alloy/process, area ratio and voiding acceptance using the manufacturer drawing; provide approved aperture output before release. U1 example is based on0.125mm stencil; that does not independently establish the common-board process. C1 and manual-resistor aperture handling also need sign-off. Manual through-hole connectors require no paste printing unless a separately validated pin-in-paste process is explicitly agreed.
Connector Drawing Record
  • J1: Phoenix1875522 manufacturer sheet hosted by RS, page2 drilling diagram visually verified: two rows of tails3.81mm apart,longitudinal3.81mm pitch,1.2mm holes.12 electrical positions have24 solder tails. Earlier web text saying only12 holes is not authoritative.
  • J2: TE ENG_CD_284514_C5.pdf,3.5mm pitch; lead verified1.2+0.1/-0mm holes. Current1.2mm drills/2mm lands retained. Exact mating plug and numbering view remain unsigned.
  • J3: lead verified1.70mm drilling requirement; current1.70mm holes/2.5mm lands,5.08mm pitch retained. Do not substitute1.4mm drilling. Procurement manufacturer identity and mating-view sign-off remain open.
  • J4: Phoenix1888687,5.08mm pitch,1.3mm drills;1.95mm lands,body10.16×9.5mm,wire-entry face at bottom board edge.
  • Inspect final P&P orientation/pin1 and physical mating plugs before energizing; PCB-view numbering must not be silently reversed into mating view.
J4 Harness Installation
Both terminals are +24V outputs; NO GND on J4. Board total remains1.75A target, not per terminal. Terminal nominal16A is only a component rating.
Selected wire: red Belden83009,18AWG,19x30 silver-plated copper,TFE insulation. Manufacturer data specifies9.2A recommended single-wire current per cited MIL-STD table and5.75ohm/1000ft nominal resistance; this is not an installed bundled-harness rating. Apply actual ambient/bundle derating and verify temperature rise. Use one untinned conductor per occupied clamp,6.5mm strip,0.5–0.6Nm torque. Do not clamp insulation or leave loose strands. Do not stuff seven wires into either clamp.
Anchor insulated wire to the chassis/tile support using a mechanical cable clamp before fan-out, so cable pull is not carried by solder joints or terminal body. Keep an unstressed service bend; define and pass a pull test for the actual mounting. There are no newly added PCB strain-relief holes. TP1 is probe-only. Downstream distribution splice and J3 supply wiring require their own rated construction.
Stackup and Output Gates
Configured1.530mm FR-4 dielectric,Dk4.3,two35um copper layers,0.6/0.3mm through vias; laminate sum1.600mm,sizeZ1.6mm. Tool totalThickness1.53mm remains inconsistent. Saving a reusable stackup failed due owner-catalog permissions: owner nico must save from the stackup editor. No saved profile applied and no vendor capability profile selected.
Before release: place/route redesigned push-pull and boost circuitry;qualify256ns load/optical timing,gate supply,startup/brownout and controller5V budget;approve effective MLCC values,stencil/mask/local0.15mm gap;confirm mating;reconcile stackup;inspect regenerated GND,source returns,all bypass loops,supply/return bottlenecks and inactive-neckdown omission. Then generate and inspect same-revision Gerber/drill/BOM/P&P with39 machine placements/board. Historical zero-airwire results do not apply to new circuitry. No fabrication-approved export,quote,order or physical assembly occurred.
  • BOM and Assembly Split

  • Copper Footprint Corrections

  • Q1–Q7

  • U1

  • Stencil and Mask — Blocking

  • Connector Drawing Record

  • J4 Harness Installation

  • Stackup and Output Gates