Nixie Watch Enclosure


Updated the enclosure to:
  • Circular body: Ø62 mm
  • Overall lug-to-lug: 78 mm
  • Lug opening: 24.6 mm at both ends
  • Clearance: 0.30 mm per side for a 24 mm strap
Updated CAD:
  • 3D Model

  • 3D Model

  • 3D Model

  • 3D Model

    Design view of Circular enclosure / 24 mm strap revision
Concentric alignment, electronics clearance, button travel, and Qi hardware exclusion were checked. Spring-bar fit remains provisional until tested with the selected 24 mm strap hardware.

No schematic yet

Talk to Flux to get started.

Circular enclosure / 24 mm strap revision
Scope and status
Completed: circular main body, rear cover, lens, rear gasket, lens adhesive, concentric carrier, and longer spring-bar placeholder regenerated. Existing asset UIDs/names and placed-node identities were retained; the current main body remains named main body v2 but now resolves to the circular source. Obsolete square main-body/carrier v1 nodes remain disabled. The unchanged button and membrane were translated outward6 mm; spring-bar nodes moved to y±35 mm. No unrelated electronics changes were made.
Completed: geometric checks described below and saved-layout read-back. Failed/blocked: visual CAD rendering returned HTTP400 key regex validation twice, including one focused recovery. Unattempted: physical testing, slicer qualification, downloaded assembly STEP inspection. Completion of this revision does not qualify the enclosure for production or an IP rating.
Exact resulting dimensions
  • True circular case cylinder: Ø62.000 mm, centered at x=y=0. The separate lugs and right-side button are intentional departures from the circular silhouette.
  • Overall lug-to-lug:78.000 mm, tips at y=-39 and+39.
  • Upper lug pair: inward straight faces x=-12.300 and+12.300 mm, measured clear opening 24.600 mm near spring-bar axis y=+35.
  • Lower lug pair: inward straight faces x=-12.300 and+12.300 mm, measured clear opening 24.600 mm near spring-bar axis y=-35.
  • Both openings implement24.0 mm strap +0.30 mm clearance per side. Their root blends lie nearer the case and do not reduce the straight strap-axis gap.
  • Lug width5 mm, thickness8 mm, boreØ1 mm, top/bottom bore web3.5 mm and tip web3.5 mm. Lug profile retainsR2 ends and R1.5 smooth concave root blends, implemented by analytic planar closing.
  • Main body bounds62×78×36.6 mm, z=-16.6..20. Closed assembly z=-19..20 gives39 mm thickness. Including unchanged cap shifted outward, x=-31..32.2 gives63.2 mm overall width.
  • Ø62 was required to retain the rectangular31×42 PCB envelope, circular clearance, circular carrier and3 mm ordinary walls; it is larger than the previous square body's50 mm width. Wearability remains provisional.
Current durable source assets
Each link offers editable Build123d and pipeline STEP/STL downloads.

Table


Current asset nameDurable source
watch-main-body-clearance.build123d

3D Model

watch-rear-cover.build123d

3D Model

watch-carrier-clearance.build123d

3D Model

watch-front-lens.build123d

3D Model

watch-rear-gasket.build123d

3D Model

watch-lens-adhesive.build123d

3D Model

watch-spring-bar.build123d

3D Model

watch-button-cap.build123d — unchanged geometry

3D Model

Other unchanged electronics/hardware sources are listed in enclosure-cad-handoff; its old square-body dimensions and shape-dependent URLs are superseded by this report.
Installed alignment and preserved interfaces
All models remain root-parented, rotation(0,0,0), scale1, Z-up. Body, lens, rear cover, circular gasket, adhesive, carrier, coil and coil recess share the (0,0) XY axis. Body/cover/carrier/lens/gasket/adhesive/coil nodes have computed position(0,0,0). During final read-back the lens had an unexpected61.9549 mm X offset; it was restored and independently read back at computed(0,0,0).
  • Circular cavityØ56; PCB corners have 1.899234 mm radial wall clearance. PCB remains31×42×1.6, top z0, four contact points(±11.5,±17) at underside z-1.6. Front stop bearing coordinates retained; stops extended to join circular wall. Existing carrier fasteners retained at(±20,±10).
  • LensØ55.5×2 at z17.2..19.2, seatØ56: 0.25 mm radial fit,0.8 mm bezel recess, 4.2 mm tube-to-lens axial gap. Two tubes unchanged: Ø11×22, centersx±7.5,z7.5, long axesY. Their mutual glass-envelope gap remains4 mm. No glass is clamped.
  • Front adhesive ring radii25.5..27.75, thickness0.2, z17..17.2; one continuous annular land.
  • Rear Qi coilØ34×1.6, z-17.4..-15.8; pocketØ35; 1.5 mm plastic to the flat exterior and0.1 mm nominal coil-bottom gap, all unchanged.
  • Rear groove centerR29.5, width2.5, depth1.5. Compressed gasket envelope radii28.452802..30.547198; full-width contact ring supported. Four rear screw pads are clipped toR27.75 rather than cutting pockets through body seal land.
  • Rear screws(±19.4,±16), M2×6, bearing facez-16.8; insertsz-14.6. Carrier M2×5 at(±20,±10), bearing facez-9; insertsz-7.8. All unchanged hardware is outside the Qi zone: nearest actual metal envelope is a carrier screw head, 3.370680 mm projected clearance fromR17 coil; rear head clearance6.156769 mm. Plastic bosses are not counted as metal.
  • Cap and membrane node transforms (+6,0,0) mm shift the existing sources to the new right wall. Aperture and counterbore translated equally. Native-kernel checks on the final uploaded body passed cap positions0,0.1,0.2,0.3 and 0.4 mm inward travel with no positive plastic interference. Silicone deformation, switch force/location, bonding and return behavior remain unverified.
  • Spring-bar nodes (0,±35,-8) mm. New simplified envelope26.2 mm installed tip-to-tip, bodyØ1.8×22.4, plunger span24.4, tipsØ0.8. Nominal modeled engagement0.8 mm per lug. This extension is PROVISIONAL, not a guaranteed fit for every nominal24 mm bar. Vendor size denotes lug width, so select/measure a bar that actually supports24.6 mm clear spacing and sufficient retention.
Verification evidence and limits
  1. Native asset pipeline compiled every updated source. Current volumes: body24464.4524 mm³, rear cover5767.1308 mm³, carrier6322.2512 mm³; each is one solid. Bounds match the dimensions above.
  2. CadQuery independent reconstruction measured both24.600 mm lug openings, R31 circular body arcs, R1.5 root blends, concentric features and the PCB radial gap. It found no positive-volume intersections for the final gasket-repair variant among body, cover, carrier, PCB, tube envelopes, lens, adhesive, coil, gasket and cap at rest. Its main-body volume differs from native by0.1467 mm³ in offset-derived detail; therefore it is a cross-check, not exact downloaded-file certification.
  3. Rear PCB+tubes motion was sampled at1 mm offsets from-40..0, and carrier motion from-25..0: no collisions in those samples. This is not continuous-path certification. Final seal repair only adds material outsideR28 at the rear, clear ofR27.75 carrier/PCB envelopes.
  4. All8 modeled screw shanks/heads cleared the plastic in reconstruction. Every blind bore retained a full1 mm solid end plug,8.042477 mm³ atR1.6. Screw heads remain0.2 mm below the rear charging face.
  5. A proxy calculation incorrectly reported cap-travel interference; this was resolved against the actual final Build123d solid, whose explicit intersection guards passed the five travel positions. Native final-source guards also passed PCB noninterference, both24.6 mm gap probes, and full continuous rear-gasket backing. Do not carry forward the proxy cap-failure claim.
  6. Layout read-back confirmed all30 current models enabled with the new source storage URLs; older square-body/carrier nodes are disabled. Existing asset and node identities were updated, not duplicated. Actual browser render inspection remains blocked by renderer HTTP400 key regex validation.
  7. Two focused repair cycles were used: robust planar root blending replaced a rejected3D fillet; then full gasket backing was restored by trimming lid pads. No further geometry refinements are included.
Manufacturing / remaining uncertainty
Process remains PETG FDM,0.4 mm nozzle,0.20 mm layers. Ordinary walls3 mm and rear plate2.4 mm retained; existing local exceptions remain1.5 mm coil wall,1.2 mm insulating barriers and separate nonprinted sealing films. Main body should print bezel-down with accessible support for internal features/lugs; rear cover charging-face down; cap outer-face down. Carrier orientation/support removal still needs slicer qualification. Circular revision increases seal perimeter; four retained screws have not been stiffness/compression-qualified, and the40 mm provisional seal-spacing fallback is not met along all arcs. No IP or load rating is claimed.
Unchanged estimated tube/board/battery/Qi envelopes are not real electronics CAD. HV insulation, actual strap/spring-bar load capacity, physical retention, printer tolerances, membrane life and seal leakage require physical validation.
  • Scope and status

  • Exact resulting dimensions

  • Current durable source assets

  • Installed alignment and preserved interfaces

  • Verification evidence and limits

  • Manufacturing / remaining uncertainty