Chat


How can I help you?

Explain project
Write a project description
Find schematic issues

Last modified 12d ago

MAX2771 Translator Selection
Implementation status — 2026-08-07
Implemented as U15 TXV0108RGYR, U16 TXU0304PWR, and U17 SN74LVC2T45DCUR. MAX_SDATA_DIR is assigned to U1 GPIOT_P_20, ball L19. All MAX digital nets are split into 1.8 V and 2.8 V sides, and independent inspection found no remaining direct U6-to-U1 connection.
Focused release review confirmed correct direction/OE polarity, exposed-pad grounding, unused-channel handling, local bypassing, and startup isolation. MAX2771_SAMPLE_BUS metadata now groups CLKOUT/I0/I1/Q0/Q1 and records the 330 ps lane-skew target. U9 local stability capacitors are C91/C92, each 1 µF.
Scope
Part selection and implementation planning only. No schematic, placement, stackup, routing constraints, or routing job was modified.
Electrical domains
  • Ti375 interface side: PP1V8, HSIO bank 2B.
  • MAX2771 side: proposed MAX_2V8_A.
  • MAX2771 sample clock: up to 44 MHz.
  • Required protection: no 2.8 V signal may reach Ti375 HSIO directly; no back-powering during the 0.95 V → 1.8 V → 3.3/2.8 V startup sequence.
Selected architecture
1. Sample clock and I/Q data: TXV0108RGYR
Selected part: Texas Instruments TXV0108RGYR, 8-bit direction-controlled low-skew/low-jitter translator, 24-pin 5.5 × 3.5 mm VQFN.
Availability note: the exact TXV0108 was confirmed as an active production TI part, but no verified exact Flux library part was found. It must be imported or created from the TI datasheet before implementation.
Rail assignment:
  • Port A / VCCA = PP1V8.
  • Port B / VCCB = MAX_2V8_A.
  • DIR fixed low for B → A translation.
  • OE is active high for disable; pull OE up to VCCA so outputs remain high impedance during startup, then drive low only after both rails are valid.
Signals:
  • B1/A1: MAX_CLKOUT.
  • B2/A2: MAX_I0.
  • B3/A3: MAX_I1.
  • B4/A4: MAX_Q0.
  • B5/A5: MAX_Q1.
  • Remaining channels reserved or tied according to datasheet guidance.
Why selected:
  • Supply range 1.14–3.6 V on both ports.
  • Up to 500 Mbps operation.
  • At 1.8 V ↔ 2.5/3.3 V conditions, channel-to-channel skew is approximately ±300 to ±330 ps maximum; suitable for keeping CLKOUT and I/Q data aligned.
  • Peak-to-peak jitter is below approximately 390 ps in the relevant published conditions.
  • VCC isolation, VCC disconnect, and Ioff partial-power-down protection.
  • Input threshold at the 2.8 V MAX side is 0.7 × VCC, approximately 1.96 V. MAX2771’s published clock-output high minimum is 2.0 V, yielding a small but positive 40 mV guaranteed DC margin.
Residual caution: the 40 mV clock-input noise margin is small. Keep the MAX-to-translator traces short, avoid series loss, place TXV0108 close to U6, and reserve the option to confirm with ADI or measure on the first prototype.
2. SCLK, CSN, SHDN, and LD: TXU0304PWR
Selected part: Texas Instruments TXU0304PWR, 4-bit fixed-direction translator with three A→B channels and one B→A channel, TSSOP-14.
Flux library: verified part UID 718d6044-87b2-4ea4-aa48-d2152857f916.
Rail assignment:
  • VCCA = PP1V8.
  • VCCB = MAX_2V8_A.
  • OE held low by default so outputs are high impedance; enable high after both rails are valid.
Signals:
  • A1 → B1: MAX_SCLK from Ti375 to MAX2771.
  • A2 → B2: MAX_CSN from Ti375 to MAX2771.
  • A3 → B3: MAX_SHDN from Ti375 to MAX2771.
  • B4 → A4: MAX_LD from MAX2771 to Ti375.
Why selected:
  • Correct fixed 3-forward/1-reverse direction split.
  • 1.08–5.5 V rails.
  • Schmitt-trigger inputs with positive threshold maximum approximately 1.92 V at 3.0 V input supply, giving positive margin against MAX2771’s 2.0 V guaranteed high entry.
  • 3.0 V→1.8 V down-translation rated 50 Mbps; sufficient for LD and control/status use.
  • Glitch-free arbitrary power sequencing, VCC isolation, Ioff, and integrated weak pulldowns.
  • TSSOP package is easy for prototype assembly and inspection.
3. Bidirectional SDATA: SN74LVC2T45DCUR
Selected part: Texas Instruments SN74LVC2T45DCUR, dual-bit direction-controlled transceiver, VSSOP-8.
Flux library: verified part UID 01bdb0ea-8bba-4b82-a345-030b80d07555.
Rail assignment:
  • VCCA = PP1V8 and A1 connects to the Ti375 SDATA pin.
  • VCCB = MAX_2V8_A and B1 connects to MAX2771 SDATA.
  • DIR referenced to VCCA and driven by a spare bank-2B FPGA GPIO.
  • DIR high: FPGA A → MAX B for register writes.
  • DIR low: MAX B → FPGA A for register reads.
  • Default DIR pull-down selects MAX-to-FPGA direction during reset, preventing the translator from driving the MAX2771 SDATA pin before firmware configures direction.
  • Unused channel A2/B2 must be tied or handled exactly as recommended by TI; it must not float.
Why selected:
  • 1.65–5.5 V operation on both ports.
  • Up to 75 Mbps when translating to 1.8 V.
  • Direction control is deterministic and firmware-controlled; avoids TXS/TXB auto-direction edge-accelerator behavior.
  • Ioff, VCC isolation, and glitch-free sequencing.
  • Small, established VSSOP package.
Limitation: there is no independent output-enable. Firmware must change DIR only while SDATA is idle and must avoid contention at the MAX2771 read/write turnaround point.
Required FPGA pin change
A currently unused HSIO bank-2B GPIO is required for MAX_SDATA_DIR. The final pin must be selected in Efinity Pin Planner from an unused bonded bank-2B pin, preserving all existing MAX signals and DDR0 reservation.
This is the only additional FPGA signal required by the selected translator architecture.
Enable and startup policy
  • TXV0108 OE: pull high to PP1V8 for startup disable; FPGA or reset-qualified logic pulls low after PP1V8 and MAX_2V8_A are stable.
  • TXU0304 OE: pull low for startup disable; assert high after both rails are stable.
  • SN74LVC2T45 DIR: default low with a resistor to GND.
  • MAX2771 SHDN should remain in its safe state until translation is enabled and the RF rail is valid.
  • Translator supplies require local 100 nF decoupling per rail at each IC; add local bulk only if datasheet/layout review requires it.
Timing and routing requirements
  • Place TXV0108 between U6 and U1, closer to U6 than U1, outside the LNA/matching/SAW corridor.
  • Route CLKOUT and all four I/Q channels through the same TXV0108 and on comparable layers/reference planes.
  • Apply a bus-length/skew constraint after the translator. Translator internal channel skew is ≤ approximately 330 ps under published nearby-voltage conditions.
  • Avoid test-point stubs on the high-rate sample bus unless implemented as very short pads.
  • TXU0304 and SN74LVC2T45 can be placed adjacent to TXV0108 on the digital side of U6.
  • Maintain uninterrupted ground and add nearby ground vias for translator decoupling returns.
Rejected translator families
  • TXS0108E/TXB0108 auto-direction devices: rejected for the synchronous sample clock/data bus because edge accelerators and direction sensing increase loading and signal-integrity uncertainty.
  • SN74AVC8T245: excellent speed and power sequencing, but its 2.8 V-side VIH requirement is 2.0 V, exactly equal to the MAX2771 published 2.0 V output-high minimum, leaving zero guaranteed noise margin.
  • Two TXU0104 devices for sample data: DC thresholds are good, but splitting clock/data across separate packages gives much poorer worst-case inter-device skew than TXV0108.
BOM and library status

Table


FunctionSelected MPNPackageFlux status
CLKOUT + I/Q down-translationTXV0108RGYRVQFN-24, 5.5 × 3.5 mmNot found; import/create required after approval
SCLK/CSN/SHDN + LDTXU0304PWRTSSOP-14Verified library part
SDATA bidirectionalSN74LVC2T45DCURVSSOP-8Verified library part
Additional BOM items after approval:
  • Six 100 nF local decoupling capacitors minimum—one per supply pin pair as dictated by each datasheet/layout implementation.
  • Pull resistors for OE and DIR default states.
  • Optional 0 Ω series placeholders on CLKOUT/I/Q for tuning if placement permits.
Selection verdict
The selected three-IC architecture is recommended for implementation:
  1. TXV0108RGYR for the timing-critical MAX-to-FPGA sample bus.
  2. TXU0304PWR for fixed-direction controls and lock detect.
  3. SN74LVC2T45DCUR for firmware-controlled bidirectional SDATA.
It provides deterministic direction control, power-off isolation, compatible 1.8 V/2.8 V rails, and substantially better sample-bus skew than multi-package fixed-direction alternatives.
No parts should be added until the user approves this exact translator set and the additional MAX_SDATA_DIR FPGA pin.
  • Implementation status — 2026-08-07

  • Scope

  • Electrical domains

  • Selected architecture

  • 1. Sample clock and I/Q data: TXV0108RGYR

  • 2. SCLK, CSN, SHDN, and LD: TXU0304PWR

  • 3. Bidirectional SDATA: SN74LVC2T45DCUR

  • Required FPGA pin change

  • Enable and startup policy

  • Timing and routing requirements

  • Rejected translator families

  • BOM and library status

  • Selection verdict