Project Idea Kickoff


Start a new project

What would you like to build, and what should it do? A rough idea is enough to start.

Waiting for input


Last modified 22d ago

Mechanical Interfaces
Selected devices for first-pass packaging
These are actual selected devices, not generic part suggestions. Library exact/fulltext lookup found no TAL220B, LP543450 or WEO012864; electrical owner must source/create corresponding off-board symbols. Mechanical model nodes do not add schematic/BOM components.
Load cell
Select HTC TAL220B 5 kg, SparkFun SEN-14729. Product, manufacturer drawing. Product specifies 55 x 12.7 x 12.7 mm; visual inspection of drawing confirms two M5 tapped holes at 40 mm pitch, centered across 12.7 mm width. Symmetric end offsets derived as (55-40)/2 = 7.5 mm. Do not confuse with 80 mm TAL220.
  • Four-wire full bridge: red E+, black E−, green S+, white S−; 200 mm leads.
  • Excitation 3–10 VDC, sensitivity 1.0 ±0.1 mV/V. 5 kg is a listed capacity.
  • Design choice: 5 kg provides headroom for 2 kg payload plus estimated <=0.5 kg platform/mat/bracket. Does NOT establish 0.1 g accuracy. Single-point mounting uses opposite ends, one lower base bearing and one upper platform bearing; no rigid parallel force path.
Battery
Select LiPol LP543450 PHR-3 / PCM / 10K NTC variant, drawing F05423_10. Supplier product, specific 3-wire drawing.
  • 1S1P protected pack, nominal 3.7 V, 1000 mAh minimum; 200 mA standard and 500 mA maximum charge, 4.2 V ±50 mV charge limit.
  • JST PHR-3, 10 kΩ ±1% at 25°C NTC B3435.
  • Charge only +10 to +45°C; discharge −20 to +60°C. Charger TS window must implement THIS pack range, not a generic 0–45°C window.
  • Direct visual drawing read: body 51±1 x 34±0.5 x 5.4±0.3 mm, wire length 50±3 mm. CAD reserve max 52 x 34.5 x 5.7 plus clearance and swelling space. No compression.
  • Drawing circuit labels pack outputs − / NTC / +; illustration red/yellow/black wires, yellow central. Connector pin numbering, view polarity and NTC return are NOT VERIFIED: do not assign physical pin1 until vendor confirmation or sample continuity/voltage test. Provision logical BAT+, BAT−, PACK_NTC; same LP543450 name also exists as a 2-wire NO-NTC variant and is not interchangeable.
Display
Select Winstar WEO012864ALAP3N00000, 1.54 inch yellow monochrome 128x64 COG OLED, SSD1309, 24-contact FPC, 4-wire SPI mode. Exact datasheet, manufacturer family and FPC options.
  • Exact drawing panel 42.04±0.2 x 27.22±0.2 x 1.45±0.1 mm; AA 35.05 x 17.51 mm. FPC 24 contacts at 0.5 mm, width 12.50±0.1, insertion tip 0.30±0.03 mm.
  • VDD 2.8–3.3 V (3.0 typ); separate VCC 12.0–13.0 V (12.5 typ), so this bare OLED requires panel boost, not just 3.3 V.
  • SPI BS1=0, BS2=0, D0=SCLK, D1=SDIN, D2=NC, other unused data pins LOW.
  • Manufacturer published mapping: 1 NC(GND), 2 VLSS, 3 VSS, 4 NC, 5 VDD, 6 BS1, 7 BS2, 8 CS#, 9 RES#, 10 D/C#, 11 R/W#, 12 E/RD#, 13 D0, 14 D1, 15 D2, 16 D3, 17 D4, 18 D5, 19 D6, 20 D7, 21 IREF, 22 VCOMH, 23 VCC, 24 NC(GND). Follow exact datasheet application components and power sequencing during capture; do not substitute SH1106 variant.
  • FPC contact face, physical pin1 handedness and exact tail route remain NOT VERIFIED. Do not freeze ZIF contact orientation or footprint until drawing/sample check. Family offers 24-pin 0.5-mm ZIF tail FPC2050002411XXXXX05; do not substitute 30-pin option. Internal FPC stays wholly within fixed front housing and never crosses platform.
Mechanical direction
Prototype PETG matte dark, 0.4 mm nozzle, provisional 0.2 mm layers. No printed snap life, IP rating, load accuracy or strength qualification is claimed. Planned exterior <=140 x 140 mm, fixed sloped front with two broad controls and wide cosmetic dark window around actual smaller OLED, rear floating platform, right rear USB-C. PCB 90 x 55 x 1.6 mm is an estimated placeholder, not a real board. Reserve front-left antenna zone away from battery, load-cell metal and rear cup platform; electrical owner must check exact module keepout. Detailed coordinate contract follows with authored CAD.
  • Selected devices for first-pass packaging

  • Load cell

  • Battery

  • Display

  • Mechanical direction