Sensor Wiring Setup


Placed 20 component(s): Q1, LED_STATUS_X, R2, R_PULLUP_Y, ESP32_SOCKET_B, NANO_SOCKET_B, ESP32_SOCKET_A, R1, R_STATUS_Y, U_SENS_Y, LED_STATUS_Y, C_FILT_Y, R_STATUS_X, R_PULLUP_X, C_FILT_X, U_SENS_X, R3, R13, NANO_SOCKET_A, R_STAR_GND
Work done
  • Integrated the two native PC817 homing sensor channels with labeled X/Y sensor terminals, 10kΩ pullups, 100nF filters, 4.7kΩ status LED resistors, Nano D9/D10 outputs, and a single 0Ω star link between GND_24V and GND_LOGIC.
  • Preserved the 100 mm × 152 mm, 2-layer board and placed the new/updated sensor parts in the connector area with no placement overlap or out-of-bounds issues.
  • Applied the required 1.6 mm copper spacing rule conservatively and documented the implementation in Homing Sensor Integration Audit.
Success criteria review
  • ✅ Native X/Y sensor circuitry integrated and connected to +24V_SENSOR / GND_24V.
  • ✅ LIMIT_X_NET connects to Nano D9; LIMIT_Y_NET connects to Nano D10.
  • ✅ Sensor terminals are documented as BRN/BLU/BLK and filters/status LEDs are included.
  • ✅ Board size and 2-layer stackup are preserved.
  • ❌ Final layout DRC is not clean: airwires and overlapping copper remain after the stricter spacing rule, so the board is not fabrication-ready yet.
Next steps
Run routing cleanup/autoroute for the updated board, then re-check DRC until the airwire and copper-clearance issues are cleared. I can continue with PCB routing/cleanup guidance next.
Route sensor nets
Review DRC violations
Verify clearance rule
Prepare Gerbers
Update audit doc

Waiting for input


PCB Placement Review
Goal
Organize the Jerky Robot V3 Control Board layout to reduce overlap risk, improve routing corridors, and prepare the board for clean routing.
Board setup confirmed
  • Board size: 100 mm × 152 mm
  • Board shape: rectangle
  • Stackup: Standard 2 Layer
  • Component side policy: top-side placement
  • Mounting holes remain at the board corners
Actions performed
  1. Enforced the required 100 mm × 152 mm board size and Standard 2 Layer stackup.
  2. Ran layout and review checks before placement.
  3. Reorganized components by functional block:
    • ESP32 / ESP32 socket block kept central with antenna edge clearance guidance.
    • Arduino Nano / Nano sockets moved closer to the central routing area.
    • Screw terminals and large connectors kept near accessible board edges.
    • X/Y sensor isolation support parts grouped near their sensor connectors.
    • Stuffer relay/driver/opto/flyback/LED support parts kept together near relay and contact connector.
    • LED/test-point/support-passive area spread into staggered rows to improve pad access.
  4. Re-ran layout/review checks after placement.
Current result
  • Component placement itself is organized with no placement overlap/out-of-bounds/keepout issues reported by the placement pass.
  • The formal board review still reports copper, airwire, and floating-copper problems because the existing routed copper/trace geometry was not regenerated after moving components.
  • Missing footprints check passes.
Remaining issues from review
  • Overlapping copper: still reported after component moves.
  • Airwires: still reported after component moves.
  • Floating copper: still reported after component moves.
Important limitation
The component placement stage can organize footprints and improve routing corridors, but the existing routed traces and copper islands must be cleaned up/re-routed after placement. The available actions in this run allowed board sizing, stackup setup, placement, and review, but did not provide a trace re-route/copper-delete operation to fully eliminate the remaining routed-copper violations.
  1. Clear or regenerate the old routing after the new placement.
  2. Re-route all nets using the updated functional block placement.
  3. Re-pour bottom GND fill after routing.
  4. Re-run DRC until overlapping copper, airwires, and floating copper are all clean.
  • Goal

  • Board setup confirmed

  • Actions performed

  • Current result

  • Remaining issues from review

  • Important limitation

  • Recommended next work