I’ll proceed one verified step at a time. First, I’m only checking the handheld’s current routing state and fresh DRC results; I won’t modify anything until that exact baseline is known.
Worked for 17 sec
flux
42 days ago
Baseline complete: 9 airwires, 1 copper overlap, and 6 ERC errors. Following the required order, I’ll fix only the single P1 copper overlap next, then rerun that one check before touching routing.
Worked for 7 mins 6 sec
flux
42 days ago
First step complete: the P1 copper overlap is fixed and verified.
Replaced the offending HH_ILIM trace with a clearance-safe route.
No components or protected USB-C differential copper were changed.
Next step: I’ll route only the RXD airwire, keep all placement fixed, and then rerun the airwire and copper checks before proceeding further.
Thought for 9 mins 48 sec
flux
42 days ago
The RXD routing attempt was blocked by local congestion. The test route was fully reverted, leaving the board unchanged at 9 airwires and 0 copper overlaps.
Next single step requires approval: reduce RXD only from 0.15 mm to 0.13 mm trace width to create a legal escape path without moving components. Approve this rule adjustment?
A rugged paired wireless welding-amperage control system consisting of a compact handheld remote, a universal protected receiver, and passive machine-family cable adapters. First-release targets remain the Lincoln Flextec 350X and Lincoln Dual Maverick 200/200X, subject to exact-interface validation.
Development State
Electronics-first proof of concept. The schematic may be used for simulator and bench-board planning, but machine connection, field trials, and production PCB release are blocked until the validation gates below are closed.
System Architecture
Battery handheld main board: RAK3172 radio/MCU, encoder/pushbutton, USB-C BQ24074 charging, MAX17048 fuel gauge, TPS63031 3.3 V conversion, and a locking cable interface to the display assembly.
Off-board display assembly: EA DOGM162W-A transflective 2x16 LCD on a small daughterboard with its own charge-pump flying capacitor, VOUT reservoir capacitor, and VDD bypass capacitor.
Universal receiver: protected 12–48 V input, LM5164 5 V buck, 3.3 V logic, watchdog, isolated SPI/analog domain, AD5293 command element, command-qualified dual PhotoMOS terminal disconnect.
Passive adapters contain only connector/pin mapping; they do not create compatibility by themselves.
Intended C/D/E remote-pot and J/K auxiliary-power mapping remains subject to final harness continuity, machine-side voltage/current measurement, simulator validation, and controlled exact-model testing.
Lincoln Dual Maverick 200/200X
Authoritative contact-by-contact mapping is still unavailable. No field connection is permitted until the exact model/variant and every contact are verified.
Communications and RF
Target range: at least 500 ft (150 m) in a representative obstructed industrial environment.
Current 915 MHz hardware assumptions apply only to US915-class operation.
Every sales region requires a legal frequency plan, matching RAK3172/module variant, approved antenna configuration, conducted/radiated verification, and certification review.
Antenna choice, enclosure effects, cable routing, metal-body shadowing, packet format, airtime/duty-cycle compliance, and coexistence testing remain release gates.
Pairing must reject commands from other units and messages that are corrupted, stale, duplicated, out of order, incompatible, or outside the active profile.
Link-Loss Policy
Existing hold-last behavior is a provisional product requirement, not an approved safety behavior. Machine command output may be held only while all of the following remain valid: receiver firmware healthy, watchdog serviced, active profile valid, isolated supply valid, command age inside the machine-specific timeout, and machine enable explicitly armed. Timeout and fallback behavior must be approved per machine before field release.
Handheld Requirements
One-hand, glove-friendly operation and prominent commanded-amperage display.
The EA DOGM162W-A display is off-board and connected by a positive-locking 8-position JST GH cable assembly; it is not part of the handheld main-PCB physical component set.
Display-local C13, C14, and C15 stay on the display daughterboard close to DS1 and must not be distributed across the harness.
Minimum 12 hours representative operation per charge.
Selected battery basis: EEMB LP502030 protected 1S LiPo, 3.7 V nominal, 250 mAh, approximately 20.5 × 32 × 5.3 mm, 250 mA maximum charge, 500 mA maximum discharge.
BQ24074 nominal fast charge approximately 201 mA and termination approximately 20 mA.
Battery procurement requires received-sample confirmation of protection circuit, connector housing, lead polarity, dimensions, temperature limits, and supplier traceability.
Approximate operating TX peak is 90 mA on 3.3 V or 116 mA reflected to a 3.0 V battery at 85% efficiency; 250 mA is a conservative qualification floor rather than an expected peak.
Display Harness Interface
Main-board header J14 and display-daughterboard header J15: JST SM08B-GHS-TB(LF)(SN), GH series, 1.25 mm pitch, side-entry SMT, positive locking.
Cable-end housings: two JST GHR-08V-S female housings with SSHL-002T-P0.2 crimp contacts, wired straight-through pin-for-pin.
The eight positions carry one 3.3 V conductor, two ground/return conductors, serial clock, serial data, chip select, register select, and reset. No charge-pump nodes cross the cable.
Table
Pin
Net
Function
1
3V3_HH
Display power
2
GND
Power/signal return
3
HH_LCD_SCLK
Serial clock to DS1 E/SCL
4
GND
Additional signal return
5
HH_LCD_MOSI
Serial data to DS1 D7/SI
6
HH_LCD_CS_N
Active-low display chip select
7
HH_LCD_RS
Register/data select
8
HH_LCD_RESET_N
Active-low display reset
DS1 remains configured for write-only serial mode: PSB and R/W are held low on the display assembly, and unused D0–D6 parallel inputs are held low locally.
Receiver Power Requirements
POC input: 12–48 VDC continuous, 58 V maximum non-transient. Do not claim 60 V nominal continuous operation with the fitted protection.
LM5164 target: 5 V, 250 mA design load, approximately 303 kHz, approximately 10.1 V turn-on UVLO, approximately 4.99 V feedback.
L10 production requirement: 150 µH shielded, Isat ≥2.1 A, thermal current ≥1.5 A, DCR ≤0.25 Ω, -40 to +125 °C. Final sourced MPN and land pattern are required before PCB release.
Machine-Output Safe-State Architecture
U10 PA0 is the machine-enable command and has a 100 kΩ hardware pull-down.
U19 optically transfers only the validated enable command to the isolated domain.
Q1 is a default-off high-side switch. ISO_OUTPUT_ARMED powers both U18 PhotoMOS input LEDs and releases U15 RESET.
R42 holds U15 RESET low whenever ISO_OUTPUT_ARMED is absent.
C46 delays re-arm after command assertion or isolated-rail recovery.
U20 reports isolated 5 V presence to U10 on PA8 (RX_ISO5V_OK).
Receiver-side SPI CS has an inactive pull-up; AD5293 SDO has its required isolated-side pull-up.
Both machine-facing A and W paths have normally-open PhotoMOS disconnection. The W path has 3.9 kΩ series limiting. The A path retains the approximately 10 kΩ effective end-to-end resistance formed by the AD5293 20 kΩ element in parallel with R40, avoiding command-range attenuation while keeping nominal terminal current near 1 mA at 10 V.
Mandatory Firmware Sequence
On boot, reset, watchdog event, profile change, invalid nonvolatile data, isolated-supply fault, or command timeout: drive RX_MACHINE_ENABLE low.
Verify the A-terminal current and D15 clamp behavior under the exact machine's maximum reference voltage and transient environment; calibration and machine acceptance must be measured, not assumed.
No machine compatibility claim until exact pinout, voltage range, source/sink current, impedance expectations, transient environment, and fault behavior are documented for the exact model/variant.
Verification Targets
No unsafe excursion during boot, brownout, watchdog reset, packet loss, reconnection, isolated-supply cycling, profile change, receiver power loss, or cable faults.
Full-range mapping validated at multiple calibration points on simulators before controlled exact-machine testing.
500-ft RF performance demonstrated in representative metal-rich industrial conditions and in the legal regional channel plan.
Minimum 12-hour handheld operation demonstrated using final firmware and approved battery source.
EMI/ESD/transient pre-compliance before field trials; enclosure sealing and impact validation after mechanical design.
Display release requires continuity and pin-1 orientation verification for both cable ends, housing/contact pull-test inspection, and confirmation that the selected cable length operates reliably at the final SPI clock rate under battery-low, ESD, flexing, and representative EMI conditions.
Physical Design Expectations
Handheld main PCB target envelope: 44.45 × 50.8 mm (1.75 × 2.0 in), PROVISIONAL.
Receiver main PCB target envelope: 44.45 × 50.8 mm (1.75 × 2.0 in), PROVISIONAL.
The 57 × 33.5 mm DOGM162 display is a separate mechanically supported assembly connected by the locking harness; its daughterboard, strain relief, cable bend radius, and enclosure clearances remain to be finalized.
Pinout/mating validation and final cable-length verification are mandatory release gates before PCB or enclosure release.
Change Notes
Converted the handheld DOGM162 from an on-main-board component to an explicit off-board daughterboard assembly.
Added J14/J15 JST GH locking cable endpoints while preserving the existing logical LCD nets.
Removed DS1 and C13–C15 from the handheld main-PCB physical component set; these remain represented in the master schematic as off-board assembly parts.
Out of Scope for First Proof of Concept
Automatic machine identification, actual welding-current feedback, arc/contactor control, fleet/cloud functions, wireless firmware update, final production enclosure tooling, and certification.