IC2 VREF Warning


The "Component Overrides" review flagged a warning on IC2:VREF.
Reports components that have been modified using the "!important" flag.
Designator: IC2:VREF; Ruleset: IC2 VREF pad6 correction
Context: This check flags items that have been modified using the "!important" flag.
Help me fix this.
I confirmed the warning comes from the IC2 VREF pad6 correction ruleset, which forces VREF’s position to X = 1.25 mm, Y = 0.95 mm using !important; it does not itself indicate an electrical error.
In Agent mode, I’ll try removing only the !important flags, verify that VREF stays at the corrected position, and recheck the warning—rather than deleting the pad correction blindly.
Continue in Agent Mode

Compact Placement Plan
Status: OWNER-APPROVED AND IMPLEMENTED, 2026-10-06. The owner confirmed “proceed with that size arrangement.” The 80 × 80 mm four-layer top-side floorplan is applied; see the Placement Results file for final evidence, bounded ground regions and unresolved findings. The proposal below is retained as the planning record, not a pending approval request.
Measured starting point
  • Rectangular 160 × 100 mm board, four copper layers, 108 onboard footprints (external R24 excluded).
  • Footprint area: 2,290 mm²; current board fill 14.3%. All onboard components currently top-side.
  • Current applied target: Standard Density (SDI) v2; JLCPCB SDI 4 Layer v1, two internal ground-reference layers. Preserve profiles and IC2 pad6 correction.
  • No approved enclosure envelope, mounting arrangement, component-height limit or fixed connector positions recorded in specification. No mounting-hole footprints or zone nodes were returned in the inspected inventory. Preserve any locked parts and inherited part keepouts discovered during implementation; do not assume their absence from compact output.
  • Placement checks identify four clearance-only component overlaps plus many power-stage findings: charger/regulator capacitors are widely separated from their ICs. Tight functional clustering is more important than indiscriminate packing.
Proposed board setup
  • PROVISIONAL 80 × 80 mm standard rectangle: 2,290 × 2.5 = 5,725 mm² routing-aware estimate, next common size 6,400 mm²; estimated footprint fill 35.8%. This is a first-pass target, not a proven minimum or approved mechanical envelope.
  • Retain existing four-layer physical stackup and SDI manufacturing limits; conventional through-vias, 0.25 mm drill / 0.55 mm diameter. Preserve component-specific hole sizes; no blind/buried vias, HDI or new drill palette.
  • Retain existing laminate, copper weights and material configuration; no heavy-copper or special RF laminate upgrade proposed without current/thermal evidence.
  • 80 × 80 is within the common ≤100 × 100 mm fabrication tier; may reduce area/panel waste relative to 160 × 100, but no quoted cost savings. A 100 × 100 fallback remains available if actual constraints prevent the proposed fit; any enlargement needs approval.
Proposed connector and block floorplan
Directions refer to a top-down board view; exact positions/orientations must respect the actual footprint and mating geometry.

Table


ItemProposed side/regionAccess constraint
J2 charging USB-CTop side, lower-left perimeter regionVertical mating access above board; enclosure needs separate charging opening
J3 programming USB-CTop side, beside J2 along lower perimeterVertical mating access above board; preserve plug-body clearance between ports
CN2 batteryTop side, left perimeterCable accessible; orient from connector model/drawing
CN1 NTC/probeTop side, left perimeter near CN2Cable accessible, outside USB plug envelope
U9 isolated analog output connectorTop side, right perimeterMachine harness access; wholly on isolated-domain side
J1 LoRa U.FLTop side, upper-right perimeter near U8Coax attachment and bend clearance; short RF path
U14 ESP32-WROOM-32UTop side, central-leftExternal antenna/coax access to module connector; avoid power-stage noise
U8 E22 radioTop side, upper-central/right, main-ground sideNear J1; keep RF route out of noisy power and isolated output areas
U15/U13/U16 programming circuitryTop side, near J3 and U14Short USB/data paths and local bypass capacitors
U11/L3 charger and U10/L2, U7/L1 bucksTop side, lower-left/left interiorTight per-stage input/switch/output loops; thermal and routing room
U2 and U4 isolation bridgesTop side, boundary before rightmost analog stripGND and ISO_GND remain separate; no copper/component intrusion across separation
IC2/U3/U5 isolated analog circuitryTop side, rightmost interior beside U9Quiet analog paths; U5 thermal space rather than maximum squeezing
No separate switches, displays or user LEDs appear in the current onboard inventory. Removed S1 is not restored.
Placement policy and verification
  • All components on top by default for easier assembly; bottom passives only if separately approved. Current area does not require double-sided assembly.
  • Place connectors/large anchors first, then coherent functional blocks, then supporting passives. No global pack operation.
  • Put decoupling capacitors at their actual IC power pins; orient capacitor banks and inductors to minimize power loops, not just center-to-center distance.
  • Preserve all pad/body clearances, inherited RF keepouts, physical connector access and thermal spacing. Isolation distance remains provisional until machine/working-voltage requirements are confirmed; compact placement does not establish a safety insulation rating.
  • Placement-only scope: do not autoroute. Final checks must include body overlap, bounds, keepouts, edge placement, power-stage and decoupling escape findings. Record any unresolved limits honestly.
  • Existing schematic ERC/brownout/battery/welder requirements remain release blockers; this placement request does not clear them.
Owner confirmation recorded
The owner approved the 80 × 80 mm top-side floorplan and connector regions. Placement was applied and resumed to restore separate bounded GND/ISO_GND reference regions. No further placement approval is pending for this arrangement; enclosure and insulation qualification remain unresolved. See the Placement Results file for exact completion status and checks.
  • Measured starting point

  • Proposed board setup

  • Proposed connector and block floorplan

  • Placement policy and verification

  • Owner confirmation recorded