Hardware Project Ideation


Yes—the project has unresolved completion and release blockers, based on the saved conversation rather than a fresh inspection:
  • Routing: the latest routing result was not verified. Earlier work reported that the bulk router could not exclude mains nets; whether the later workaround succeeded is unclear.
  • Mains safety: qualification of the three onboard 120 VAC relay channels remains unfinished, including fuse/protection ratings, allowable lamp loads, and PCB isolation.
  • Release checks: final electrical/layout checks and manufacturing-file generation and verification remain incomplete.
  • Usage: previous responses reported exhausted ACUs, but I cannot confirm the current balance or that usage is still blocking execution.
The display question is resolved: a four-pin I²C OLED, powered at 3.3 V. The immediate next step is to inspect the saved routing results and current design checks—not restart the design; the board is not yet fabrication-ready.
okay, so no hard blockers, I reloaded ACUs, please proceed.
I’ll resume from the saved routing and check results, preserving completed work. The usage limit is cleared; I’ll verify and address the remaining engineering blockers before treating the board as ready to manufacture.
The recovered routing reached 27 remaining connections, but a second routing result then applied and introduced substantial copper conflicts. I’m checking whether those conflicting additions can be removed selectively without discarding the good routing; fabrication remains blocked.
"Schematic Build Checkpoint" completed.
The conflicting routing is now isolated: fresh checks show 27 remaining connections, zero shorts, and zero critical power-stage errors. I’m addressing the remaining capacitor-rating and relay-footprint findings before the final routing cleanup; 15 of those connections are still deliberately held in the mains section.
"PCB Placement and LV Routing" completed.
I recovered the routing, but concurrent edits to the same capacitor placements now block safe continuation; the latest checks show 38 unrouted connections, 17 shorts, and six critical power-placement errors, documented in Placement Routing Status. I’ve paused further edits to avoid overwriting other work—the board is not fabrication-ready.
Can you pause any other editing or automation on this project and confirm I have exclusive access to make changes?

5V Buck Replacement
Disposition
Completed bounded schematic replacement at circuit checkpoint f64f794d, 2026-10-20. This replaces the failed LM2596/L1 coordination, not the overall motherboard qualification. No PCB placement/routing/rules edits or physical tests were performed. Current schematic:163 components,119 net identifiers,12 groups;116 connected identifiers and three empty. Not fabrication, purchase or energization ready.
Topology and sourced decision
U1 is now Diodes AP63205WU-7, fixed5V synchronous buck in a verified library TSOT-23-6 footprint, rather than LM2596T-5.0/NOPB. AP63205 fixed5V feedback is connected directly to the output-capacitor node after L1, with no external divider.
Exact mapping:FB1→5V_PERIPH,EN2/VIN3→12V_PROTECTED,GND4→GND,SW5→BUCK_SW,BST6→BUCK5V_BST. C28 connects BST to SW, never GND. Pin functions and100nF bootstrap value are vendor sourced. EN toVIN is explicitly permitted for automatic startup; this is not an external precision UVLO redesign.
Vendor AP63205 application values:4.7uH L,10uF input,2x22uF output. Protected input remains nominal12V from the existing adapter/protection network; minimum10.9V is an existing budget assumption, not a measured value. IC recommended VIN range3.8–32V does not permit claiming5V regulation with VIN below its required headroom.
Exact BOM delta

Table


ReferenceBeforeAfter / disposition
U1TI LM2596T-5.0/NOPBDiodes AP63205WU-7;library UID1fef4b1e-d878-4676-a22c-cee2731fe3c1,versionbfba8d82-f055-4047-ae18-ba70bc338f49;TSOT-23-6
L1YJYCOIN YSPI1050-680M68uHCoilcraft XAL5030-472MEC4.7uH;library UID55cc0105-345d-4f2d-965d-b913510b3e0b,version1d024ff9-48db-4156-ba27-de86a4ac8046
D6SS34LF asynchronous catch diodeRemoved; no other block used it. Other flyback/input diodes retained
C2SamYoung NXA25V220M8x11.5,220uF radialChanged in place to generic22uF25V ceramic1210,first COUT;removed obsolete electrolytic MPN/manufacturer/datasheet/LCSC identities
C26AbsentAdded generic10uF50V ceramic1210,CIN from protected12V toGND
C27AbsentAdded generic22uF25V ceramic1210,second COUT from5V toGND
C28AbsentAdded generic100nF25V ceramic0603,BST-to-SW
C1470uF50V Aishi ERJ1HM471G16C35TRetained shared protected12V bulk for both bucks/DC branches;not a substitute for localC26
C3/C16,U6/L2 and downstream railsExistingUnchanged;C3/C16 belong to peripheral-buck input bank
New capacitor values/packages are reference-based nominal selections, not qualified exact procurement parts. X7R is a procurement requirement in Role Details, not a fabricated MPN or proven bias curve.
Current-limit and inductor coordination
AP63205 high-side peak limit2.5/2.8/3.1A min/typ/max and low-side valley limit2.5/3.2/3.9A are sourced over the stated IC electrical-characteristic conditions. Coilcraft XAL5030-472 has6.7A Isat,40mohm maximum DCR,4.3A Irms at20C rise and5.9A at40C rise. Isat is a 25C,30% typical inductance-drop datum, not a guaranteed minimum over temperature; thermal-rise currents are reference values, not absolute maximum ratings.
The sourced6.7A saturation datum is above both the3.1A maximum peak threshold and3.9A maximum valley threshold. This removes the previously known4A-versus7.5A mismatch by replacing the whole power stage, not by relying on low average load. It does not prove a guaranteed all-temperature fault peak: numerical current-limit propagation delay/overshoot was not obtained, and hot inductance/thermal behavior remains to qualify. Cycle-by-cycle peak protection and hiccup are documented; two datasheet descriptions use differing hiccup timing wording, so no precise hiccup-time guarantee is adopted here.
Actual operating allocation
No load expansion:entire5V rail<=0.75A,entire peripheral3V3<=0.40A,and DC1/DC2<=0.25Aeach simultaneously,including all onboard/external loads and startup. Regulator2A family capability is not the released board load rating. Existing assumed input budget remains1.0914A,rounded1.10A,using10.9V protected input,80% assumed efficiency and10mA overhead,against1.5A adapter ceiling; actual efficiency/protection/cable/inrush must be measured. Allocations are not hardware current limits.
Capacitor and simulation limitations
Vendor recommends input RMS current rating above input RMS current,with a greater-than-half-maximum-load rule of thumb, and low-ESR output ceramics. Exact C26/C2/C27 MPN,DC-bias/temperature/aging effective capacitance,ripple/ESR and stability are unverified fabrication holds; nominal voltage/package does not prove effective capacitance. C1 G16 ripple/ESR/inrush qualification remains open. No claim is made that bias curves or guaranteed effective-capacitance floors were obtained.
No SPICE/control-loop/switching simulation was run. Datasheet-reference capture and ERC do not establish transient stability,efficiency,EMI,current-limit overshoot or thermals. Before energization use completed isolated,current-limited PCB hardware only after placement/short/parts review;scope startup/shutdown,min/max loads,relay steps,short recovery,slow ramps and brownouts,then temperature/EMI qualification. Preserve existing fresh-edge interlock tests and all mains safety holds.
Verification evidence
  • Read-only schematic confirms all6 U1 pins,2 L1 pins,C26/C27/C28,retainedC1/C3 and changedC2 nets;D6 absent.13 introduced floating-pin findings resolved by wiring.
  • Read-only PCB tree confirms U1six mapped SMD pads,L1two mapped pads,and regenerated C2two-pad1210 rather than former radial footprint. Full DFM/land-pattern audit and placement review remain unattempted.
  • FreshERC2026-10-20T16:28:46.027Z:20Errors,0Warnings,same categories/count as previous checkpoint:10undriven and10missing-power. Floating,shorted,pin-conflict,single-pin andNC checks pass. U1VIN has protected input connectivity; U12/U13/U16 power flows throughU1SW/L1,which the checker does not propagate. No errors suppressed or pin types falsified.
  • Fresh selectedDRC2026-10-20T16:31:03.943Z:MissingFootprints success;1overlapping-copper Error between holderF4 and newL1;1InvalidPads Info onBZ1. Freshairwire check16:31:24.390Z reports408. These are real unfinished-PCB gates; noPCB fix was authorized.
  • Independent smart-review tool was not exposed by discovery; no independent review is claimed.
Batch status
Completed:topology replacement,BOM delta,source-based nominal fault-current comparison,connectivity/footprint readback,ERC and selectedDRC,record update. Failed/incomplete:overall rail release qualification and cleanPCB/ERC release. Unattempted by scope:PCB placement/routing,simulation,physical/thermal/fault/EMI tests,exports. No single part-specific sourcing blocker remains for the schematic replacement.
  • Disposition

  • Topology and sourced decision

  • Exact BOM delta

  • Current-limit and inductor coordination

  • Actual operating allocation

  • Capacitor and simulation limitations

  • Verification evidence

  • Batch status