Vintage Dictation Mic


Thought for 6 mins 26 sec
Thought for 9 sec
Managing 1 task
Thought for 10 sec
3/3 Independently review corrected prototype package and document remaining release blockers

Fix board manufacturing defects and sourcing — completed; unsupported ERC source declarations remain blocked

Resolve case print warning and assess thickness/microphone fit — completed; physical PTT tolerance qualification remains open

Independently review corrected prototype package and document remaining release blockers

Thought for 21 sec
Awaiting 1 task
"Vintage Mic Review" completed.

flux

The review confirms the microphone correction and board spacing fixes, but the files still aren’t cleared for ordering. Three power-source metadata errors can’t be corrected with the available tools, and the button’s safe travel still needs confirmation; I’m recording those blockers clearly.
Thought for 3 mins 32 sec
Thought for 9 sec
Awaiting 1 task
"PCB Manufacturing Package" completed.

flux

I fixed the board spacing, connector holes, missing part numbers and microphone pin mapping; all six case files also pass a slicer check—but don’t order yet.
Remaining blockers:
  • Three electrical-check errors need a power-source metadata correction the available tools couldn’t apply.
  • The button’s safe switch travel needs confirmation.
  • Part availability and manufacturer approval are still pending.
The findings are in the Independent Review Summary; the next step is Flux support for the editing limitation, followed by switch and manufacturer checks before spending money.

Board Bring-Up Plan
Preconditions
  • Inspect orientation and soldering for U1, U2, U3, MK1, LED1, J1, SW1, and all five test points.
  • Confirm SW1 pads 1/2 are the 3V3_IO common side and pads 3/4 are the PTT_ACTIVE common side.
  • Confirm no shorts between VBUS_RAW, +5V_USB, 3V3_IO, 1V8_CORE, 3V6_A, VREF_1V75, and GND.
  • Use a current-limited USB source or USB power analyzer for first power.
1. Unpowered checks
  1. Check VBUS_RAW and +5V_USB to GND for shorts.
  2. Verify SW1 is open released and closes only under follower actuation.
  3. Released: PTT_ACTIVE to GND should measure approximately 100 kΩ.
  4. Verify LED1 pad 1/cathode is on GND and pad 2/anode reaches PTT_ACTIVE through R4.
  5. Verify R10 biases MIC_AC to VREF_1V75 and R11 biases MIC_GATED to VREF_1V75.
2. First power and current
  1. Apply 5 V with a 100 mA initial current limit; increase only if startup proves clean.
  2. Expected normal input is about 40 mA; investigate readings above the 50 mA production design ceiling.
  3. TP1 (+5V_USB): verify source voltage after F1 drop.
  4. TP2 (3V3_IO): verify approximately 3.3 V and stable.
  5. Verify 1V8_CORE, 3V6_A, and VREF_1V75 at their bypass capacitors.
  6. Released: TP3 (PTT_ACTIVE) low, LED1 off, U3 open.
  7. Check C1 population is 4.7 µF; total nominal direct attach capacitance is 5.0 µF and +20% tolerance total is 6.0 µF.
3. USB enumeration and power states
  1. Connect through a USB current/power analyzer to a known-good USB 2.0 host.
  2. Confirm firmwareless CM108B enumeration; no flashing or firmware file is required.
  3. Read the configuration descriptor and confirm the PWRSEL-low 500 mA bus-powered state.
  4. Record pre-enumeration current; pass target is below 100 mA, expected near the high-30-mA range.
  5. Confirm microphone capture endpoint. Playback endpoints may appear and are intentionally unused.
  6. Force USB suspend and record current. LED must remain off; expected external always-on load is about 0.12 mA plus leakage, with CM108B specified at 1.58 µA typical. Treat host-limit failure as a blocker because device maximum suspend current is not published.
4. PTT truth-table validation

Table


StateTP3 PTT_ACTIVEU3 NO-COMLED1Capture
Released / startupLowOpenOffMuted
Pressed / latched~3.3 VClosedYellow/amber onUnmuted
Cycle momentary press, latch, down-slide release, and spring return. Reject bounce, follower hang-up, LED/audio disagreement, or failure to return low.
5. Analog DC and audio checks
  1. With a high-impedance DMM, verify VREF_1V75 near 1.75 V.
  2. Released: verify MIC_AC and TP5 (MIC_GATED) both settle near VREF_1V75; neither may approach below 0 V or above 3V3_IO.
  3. Pressed: verify both terminals remain at nearly the same DC voltage while AC microphone signal passes.
  4. Probe MK1 output before C10, MIC_AC after C10, and TP5 after U3 using an AC-coupled/high-impedance instrument.
  5. Released audio must be strongly muted. Measure mute attenuation and residual feedthrough; record the result because it is not guaranteed by ERC.
  6. Pressed audio must be intelligible without clipping, oscillation, hum, or excessive level step.
  7. Record switching click/pop at press and release. Equal 100 kΩ VREF bias on both U3 terminals should minimize DC step; reject objectionable clicks and adjust bias/coupling only from measured evidence.
6. Test points
  • TP1: +5V_USB
  • TP2: 3V3_IO
  • TP3: PTT_ACTIVE
  • TP4: GND
  • TP5: MIC_GATED
7. Mechanical qualification
  • The enclosure follower must be redesigned from the previous offset D2LS geometry to the centered GT-TC084A actuator.
  • Qualify the approximately 5.2 × 5.2 × 1.5 mm switch envelope, 0.25 mm travel, 1.6 N force, overtravel, side-load avoidance, and reliable spring return.
  • Use the provisional actuator-location change from approximately (-15.14, 4) to (-14, 4), then replace it with measurements from the assembled PCB before freezing CAD.
  • Verify microphone acoustic inlet, LED light path, and down-facing USB-C cable fit.
Pass criteria
  • No overcurrent or abnormal heating; active current at or below the 50 mA design ceiling.
  • Stable required rails and both switch analog terminals near VREF at DC.
  • Repeatable USB enumeration with 500 mA descriptor state; pre-enumeration below 100 mA.
  • Suspend current compliant on measured hardware.
  • Default-muted truth table and LED/unmute identity verified.
  • Acceptable mute attenuation and switching-pop measurements.
  • Reliable mechanical return without overstress.
No firmware loading step exists because CM108B is firmwareless; no firmware project or firmware file is required.
  • Preconditions

  • 1. Unpowered checks

  • 2. First power and current

  • 3. USB enumeration and power states

  • 4. PTT truth-table validation

  • 5. Analog DC and audio checks

  • 6. Test points

  • 7. Mechanical qualification

  • Pass criteria