Mic Industrial Design


continue
I’ll correct the two localized shell-clearance errors, preserve the current silhouette, and recheck the full press-and-slide path.
Sent message to Microphone Enclosure Redesign
"Microphone Enclosure Redesign" completed.
The attempted correction removed the shuttle collision in testing, but exposed another tight paddle clearance—0.255 mm versus the required 0.35 mm—so I did not install it; the existing assembly remains unchanged and is not ready to print.
I recorded the failed check and exact remaining location in the project files’ verification and print guide.
After these repeated unsuccessful repairs, I recommend a free Flux engineer review before another geometry pass.

Get Free Expert Help

We want to get the prototype into your hands fast. Speak with one of Flux's in-house electrical engineers to review your project.

Collins, Flux electrical engineer
Ryan, Flux electrical engineer
Nico, Flux electrical engineer

Collins, Ryan, Nico — real humans who've shipped real hardware


Waiting for input


Project Specification
Project Overview
  • Status: Draft
  • Compact, one-handed USB dictation microphone inspired by a vintage police-radio microphone.
  • Intended to provide an intentional push-to-talk interaction for voice commands and agent dictation.
Intended Use
  • Indoor desktop and handheld use with a computer.
  • Right-handed operation.
  • First revision is a functional prototype with production-intent PCB assembly and a lab-printed enclosure.
What the Device Should Do
  • Appear as a standard wired USB microphone to the host computer.
  • Begin active capture while the side PTT control is pressed.
  • Allow the PTT control to be pressed and slid upward into a mechanically latched active state.
  • Provide an unambiguous visible active indicator.
  • Operate entirely from USB power without a battery.
Main Features
  • Recessed bottom USB-C receptacle for a standard detachable cable.
  • Front microphone grille and internal microphone acoustic path.
  • Large left-side PTT paddle positioned for a right-hand grip.
  • Press-then-slide-up mechanical latch with a visible physical state.
  • Warm active indicator, provisionally amber/red.
  • Compact, chunky, beige vintage utility aesthetic.
Mechanical System Architecture
Reference-inspired enclosure revision — 2026-10-07
Stronger reference-led refinement — 2026-10-08
Current installed disposition: five genuine polar rings plus center hole (91 holes total), slim nested-pivot paddle, projecting hood removed, fine horizontal divider and lower-left status outlet. Rest envelope is 69.6 × 120 × 32.2 mm; prior 76.3 mm width and mesh/1.0 mm feature defects are historical and superseded. Current paddle native mesh passes strict topology; cap and stop are 1.4 mm. Motion acceptance remains HOLD: two local front/shuttle remnants intersect by 0.24 mm³ at full press, and upper paddle transition clearance reaches 0.027919 mm versus the required 0.35 mm. Initial refinement plus two diagnosed corrections used; an additional local front-clearance correction requires approval. Upper side recess is still partly visible; long printed light-guide efficacy and physical fit/force/switch qualification remain unverified. See Enclosure CAD Verification and Enclosure Print Guide for exact locations, native asset links, actual render and test evidence.
  • User rejected the prior candidate's grille arrangement, paddle elegance and front-face rhythm; the supplied photographs are the primary qualitative form reference, not merely generic inspiration.
  • Use genuine concentric circular rings of evenly spaced holes, not a Cartesian hole grid cropped to a circle. Keep an open acoustic path to the fixed microphone.
  • Make the paddle a restrained, slender, smooth side lever with a visually concealed upper pivot. Remove the prominent rectangular hinge hood and exposed linkage from the primary silhouette where geometry permits; maintain real pivot operation and existing press-then-slide-up latch.
  • Compose the front as a quiet upper acoustic zone and lower control/status zone with a subtle horizontal division, generous margins and restrained indicator. Do not copy the reference's extra black front button, which has no required electrical function.
  • Preserve fixed PCB/electronics, beige PETG, screwless construction, bottom USB-C and right-handed operation. Avoid shrinking the enclosure through existing fit envelopes; any control/window move must preserve the actual optical/mechanical path.
  • User explicitly authorizes additional focused geometry repair for the native paddle mesh defects and undersized loaded cap/stop features, alongside this form refinement. Track this new scope separately without concealing previous repair history; use at most two diagnosed correction cycles after its initial build and report remaining blockers honestly.
Installed candidate status: rectangular body 66.6 × 120 × 32 mm; upper hinge hood increases overall width to 76.3 mm. Genuine upper pivot plus 6 mm latch slide is installed, with integrated circular perforations. Nine sampled poses have no unintended modeled overlap; this is not continuous-motion or physical qualification. Manufacturing HOLD: paddle native STL has eight degenerate facets; rear capture cap and angular-stop rib are 1.0 mm rather than the 1.2 mm loaded-feature starting rule. Initial redesign and two focused corrections are complete; further geometric repair requires an approved additional scope. Detailed current assets, evidence and render are in Enclosure CAD Verification; print instructions and HOLD are in Enclosure Print Guide.
  • User-selected direction: clean rectangular body and an upper-pivoting side PTT paddle, inspired by the two supplied microphone photographs rather than copied 1:1.
  • This direction supersedes the old concept's tapered body, oversized corner radii, prominent grille bezel and translating-only paddle. Use parallel sides, modest corner radii, a flatter face, an integrated understated acoustic grille and a smooth dark paddle.
  • Preserve approximately 120 mm height, beige PETG, left-side PTT for right-hand grip, amber active indication, underside USB-C access, screwless serviceable shell and the existing PCB placement.
  • Preserve momentary press and press-then-slide-up latching. Implement the upper paddle pivot in a captured sliding carrier if required; keep pivoting press and latch translation as distinct constrained motions.
  • Preserve the current nominal SW1 depression target of 0.25 mm without implying a qualified safe-overtravel or electrical-make limit. Switch force, mounted height, print fits, return reliability and cycle life remain PROVISIONAL and require physical testing.
  • The supplied photographs establish visual/mechanism intent, not measured dimensions. The existing actual 40 × 85 mm PCB and saved component geometry govern fit; the earlier provisional PCB description is historical.
  • This is an explicitly requested industrial-design redesign, not an extension of the exhausted historical mechanism-repair loop. Historical validation does not certify redesigned parts; require fresh clearance evidence and record any new unresolved failures.

Diagram


Two-part FDM shell Single main PCB Side PTT paddle and latch Front acoustic grille Indicator light pipe or window Bottom USB-C access Board-mounted microphone
  • FDM-printed PETG enclosure, split into a tool-free snap-fit base and lid with no screws.
  • PCB positively retained inside the shell without user-installed fasteners where practical.
  • Separate printed side paddle actuates a PCB-mounted switch; mechanical enclosure geometry provides the latch.
Electrical System Architecture

Diagram


USB-C 5 V and USB 2.0 ESD and input protection CM108B firmwareless USB audio controller Microphone front end PTT switch Active indicator USB host
Hardware Subsystems
  • USB interface: USB 2.0 full-speed device through USB-C.
  • Audio capture: LMA3722T421-OA5 analog MEMS microphone into the CM108B mono ADC/microphone-booster path.
  • Control: mechanically level-sensitive PTT directly enables a TS5A3166 series audio-path switch; a pull-down makes unplug/boot default muted.
  • Indicator: amber LED is driven from the same hardware PTT_ACTIVE net as the audio switch, so it lights only when the microphone path is electrically enabled.
  • Protection: USB ESD protection and appropriate power filtering.
Interfaces and Connections
  • USB-C receptacle on the bottom wall.
  • Front acoustic inlet behind a grille.
  • Left-side finger-operated PTT paddle.
  • Front/top-front active indicator visible during normal use.
  • Internal programming/debug pads permitted, with no user-facing opening required.
Power and Runtime Expectations
  • USB bus powered; no battery and no charging subsystem.
  • Target operation from a standard 5 V USB port.
Power Tree and Power Budget
  • USB-C VBUS → resettable fuse → protected +5V_USB rail → CM108B AVDD/DVDD.
  • CM108B internal regulators provide 3V3_IO, 3V6_A, and 1V8_CORE; no external regulator is required.
  • The former 105 mA budget is retired. Current budgeting uses a 50 mA engineering ceiling assumption, not a measured or guaranteed maximum; typical-current estimates require prototype validation. The 500 mA bus-powered USB descriptor remains unchanged. The500 mA hold fuse is fault protection, not proof of USB current compliance.
  • Suspend LED-off behavior is conditional/not verified, not unconditional: the mechanically pressed/latched SW1 can keep PTT_ACTIVE high while3V3_IO remains powered. Measure suspend current in released, pressed and latched states before claiming compliance.
  • Detailed calculations are maintained in the Electronics Architecture and Power Budget project file.
Manufacturing and Assembly Expectations
  • PCB fabrication and assembly by JLCPCB.
  • All populated PCB components must be available through LCSC/JLCPCB assembly inventory at design time.
  • Avoid hand-soldered wires, off-board switches, and custom cable assemblies.
  • Enclosure and printed moving parts will be FDM printed in the user's lab; enclosure assembly must not require screws.
  • Standard detachable USB-C cable is external and not a custom product part.
Firmware-Relevant Hardware Requirements
  • CM108B implements USB Audio Class 1.0 without a field-programmed MCU.
  • No firmware image, programming header, or factory flashing step is required.
  • Momentary and mechanically latched behavior both use the physical switch level to enable the microphone signal path.
  • The active LED shares the hardware unmute state and is not a USB-power indicator.
Physical Design Expectations
  • Compact one-handed body, approximately 120 mm tall as an initial size target.
  • Chunky vintage police-radio-microphone character.
  • Beige printed body with dark contrasting grille and PTT paddle.
  • Designed primarily for right-hand use; PTT is on the left side.
  • Recessed USB-C opening at the bottom.
  • PROVISIONAL PCB envelope: 85 mm × 40 mm × 1.6 mm, with 10 mm estimated top-side component height and 2 mm estimated bottom-side height.
Important Design Decisions
  • Wired USB-C instead of wireless to minimize complexity, latency, battery bulk, and sourcing risk.
  • Detachable standard cable instead of a captive coiled cable to avoid separately sourced cable assembly.
  • Mechanical press-and-slide latch instead of software toggle behavior.
  • Industrial design and enclosure precede electronics architecture and schematic capture.
Assumptions
  • Indoor, non-sealed use.
  • No speaker, display, battery, belt clip, or wireless connectivity in the first revision.
  • No enclosure screws; snap fits are PROVISIONAL pending print-fit and cycle testing.
  • PETG, 0.4 mm nozzle, and typical lab FDM tolerances unless later overridden.
  • The provisional PCB envelope may be adjusted after electronics architecture and component selection, while preserving the accepted external form.
Change Notes
  • Initial specification created from the industrial-design discussion.
  • Documentation closure2026-10-06, reviewed revision#d865ceb5: corrected exact-MPN microphone mapping1OUT/2VDD/3,4GND; native0DRC Errors/0Warnings,3ERC source-driving Errors and1LED1 Warning. No check waived. Release HOLD: source metadata, PTT tolerance/safe force, U3 stock and vendorDFM/assembly. No physical design change or export regeneration in this closure.
  • Project Overview

  • Intended Use

  • What the Device Should Do

  • Main Features

  • Mechanical System Architecture

  • Reference-inspired enclosure revision — 2026-10-07

  • Stronger reference-led refinement — 2026-10-08

  • Electrical System Architecture

  • Hardware Subsystems

  • Interfaces and Connections

  • Power and Runtime Expectations

  • Power Tree and Power Budget

  • Manufacturing and Assembly Expectations

  • Firmware-Relevant Hardware Requirements

  • Physical Design Expectations

  • Important Design Decisions

  • Assumptions

  • Change Notes