Routing continuation handoffRequest and constraints
User requested completion of remaining Pet Robo PCB work. Approved baseline: 100 × 100 mm, two layers, all five modules on Top, edge USB access, antenna clearance and microphone/audio separation. Preserve GPIO assignments and prior schematic freeze; explicit approval for connecting ESP1 GND has not been obtained.
Work this session
Recovered independent placement review and resumed existing layout work with a focused instruction to source actual antenna geometry, correct exclusion, complete existing-net ground pour/routing, and run fresh checks. No final build report or fresh check results were retrieved before usage exhaustion. A completion notification arrived afterward; **retrieve the persisted completion report before mak...
I resumed the antenna-clearance and routing work, but couldn’t retrieve and verify the final results before execution stopped, so I can’t confirm routing completion or fabrication readiness. I saved the continuation state in Routing continuation handoff.
Remaining work includes fresh layout/connectivity checks, confirmation of physical module fit, and explicit approval to connect the missing ESP32 ground without violating your earlier schematic-freeze instruction.
Status: ROUTED EXISTING NETS — NOT FUNCTIONALLY OR FABRICATION RELEASED. Verified 2026-10-21. This report supersedes the routing-deferred portion of Placement Checkpoint; the approved module positions are unchanged.
Assigned scope and outcome
Completed: existing-net routing, current-aware width rules, Bottom-only existing GND pour, pre-route feasibility check, final DRC/ERC and read-only visual/geometry checks.
Completed: retain 100×100mm rectangular carrier, two copper layers, all five modules Top, original GPIOs, and live editor locks. No schematic, component property, pin, net name, pad geometry or connectivity changes. No placement moves were necessary for routing.
Failed / blocked: verified RF geometry and final clean placement release. Exact antenna projection relative to headers remains unresolved; one ESP1 keepout Error persists after conservative additional exclusion. This was not hidden by shrinking/disabling the RF zone.
Blocked by explicit schematic freeze: ESP1 has no GND connection to the carrier. Zero airwires is only proof of routing the existing netlist, not proof of a functional circuit.
Unattempted by instruction: exports, fabrication ordering, firmware and enclosure work. No board cutout was guessed or introduced.
Routing result and fresh checks
Auto-route job auto-layout-e1ac6f11-e21a-48a1-be11-2a6120b5a40d, one campaign attempt: converged,13→0 airwires, no unrouteable nets. Authored71 trace segments,0 routing vias; all68 original pads remain. Current inventory:5 elements,5 footprints,17 nets,2 RF exclusion zones. Empty nets retained.
Fresh get_checks at 2026-10-21T14:52:30.565Z:
Table
Review area
Errors
Warnings
Exact remaining issue
Copper/routing DRC, including airwires
0
0
All existing nets routed; no redundant/floating/overlapping copper, via-in-pad, invalid-layer, protected-intrusion or corner-radius errors
Placement
1
0
ESP1 overlaps the RF exclusion region; exact physical antenna datum remains unverified
Floating ESP1 pins, including all four GND pins; unused pins and ground omission require electrical review, not layout-only no-connect tagging
Thus 0 airwires;1 unresolved blocking layout/placement finding, plus4 manufacturing metadata errors and34 ERC errors. Invalid Pads has3 Informational, not Error/Warning, entries for U3/SPK1/MAX9837A footprints; no guessed footprint repairs attempted. Earlier full schematic review also had5 schematic-legibility warnings, untouched under freeze.
Read-only routing_state independently reports0 airwires and0 redundant traces. Bottom GND copper=8136.528mm²,1 island,0 stitching vias; Top GND copper=0. The single connected Bottom island joins existing mic/OLED/amp grounds only; it deliberately does not short un-netted ESP ground pads. Final layout image shows routes avoiding both persisted RF reservations; this is not proof those reservations cover the real antenna's required neighborhood.
Board, placement and manufacturing
100×100mm centered at(0,0), standard-2-layer physical stackup.35µm copper each side;1.499mm FR-4 core. Saved Standard2Layer v1 and StandardDensity(SDI) v3 profiles remain applied; no vendor selected. Conventional through-via process, not HDI. Board envelope and bought-module assembly fit remain provisional.
Component origins(mm), CCW rotation, all Top:
Table
Module
X
Y
Rotation
ESP1
−26
−18
0°
OLED1
14
15
90°
U3
30
38
0°
MAX9837A
−9.5
−25
270°
SPK1
28
−20
180°
USB end faces bottom; nominal devkit outline ends Y=−49.37mm,0.63mm inboard. Other modules do not occupy BOOT/RESET or cable approach region. Mic remains upper-right, amp/speaker lower; assembly/cable-shell clearances and acoustic isolation are not certified. No lock was overridden.
Layer Routing Strategy
Top preferred horizontal(0°), signals and power; Bottom preferred vertical(90°), signals as necessary plus GND pour. Router preferences are soft;45° escapes are permitted.5V and S± are short Top routes;3V3 uses both layers through existing through-hole pads with no extra vias. No carrier USB/RF feed or impedance-controlled/differential-pair nets were introduced, so no EM claim is made. Existing I2S/GPIO pin mapping retained.
Widths, current allocations and power limits
Effective net rules and actual routed copper geometry inspected after routing:
Table
Net
Width
Basis
5V
1.0mm
Conservative approximately1A DC amplifier allocation
S+,S−
1.0mm each
BTL load current; neither output is GND
3V3
0.5mm
Conservative module carrier supply path; actual bought OLED current unresolved
GND escapes
0.127mm
Manufacturing minimum; Bottom fill carries bulk return
Digital signal nets
0.15mm
Existing SDI process preference
MAX98357A3.2W into4Ω at5V is a typical10%THD+N rating, gain12dB, load4Ω+33µH; typical2.5W at1%THD+N. Derived sine sizing currents at3.2W/4Ω: sqrt(P/R)=0.894A RMS and sqrt(2P/R)=1.265A peak per BTL output. These are calculated allocations, not measured currents.1mm copper is a conservative trace selection for these loads, not a validation of USB source capacity.
Amplifier quiescent current at5V/+25°C is2.75mA typical/3.35mA maximum. Approximate DC amplifier load0.8A derives from3.2W/(5V×0.8), with 80% efficiency explicitly assumed, not quoted. Exact4Ω full-power efficiency remains unresolved; datasheet92% figure applies to8Ω, not4Ω.
Full power budget is not closed: source/USB current advertisement, ESP devkit regulator current/thermal margin, bought OLED current, mic board variant and combined peak load were not verified. Do not assume an ordinary500mA USB source supports full speaker output plus ESP Wi-Fi. No new protection/regulator/capacitor was added under freeze; board-level bulk and local decoupling remain an electrical-review item.
RF exclusion: what is protected and what remains unknown
Official drawing supports62.74×25.40mm board dimensions and antenna beyond the pin1 end. It does not yield a sufficiently verified numeric antenna projection/datum for this library footprint;22.86mm header-row spacing is present in the library but remained parser-unverified against the official mechanical evidence. No pad changes were made.
Espressif web guidance consulted: https://docs.espressif.com/projects/esp-hardware-design-guidelines/en/latest/esp32s3/pcb-layout-design.html . It prefers antenna beyond the carrier edge, recommends carrier cut-away beside/under antenna when overhang is not possible, and discusses15mm clearance inside the enclosure. This carrier's rectangular board still exists under the reserved region. Copper removal alone does not prove the mechanical/RF guidance is satisfied. Authoritative antenna registration and physical carrier cutout/edge-placement approval may still be required.
Original ESP-owned48×22mm rectangle retained in full: local center(0,42), absolute X−50…−2,Y13…35mm. All copper layers, STD zone type,0.15mm external keepout. Existing selector ruleset b0ce1ab5-6873-435e-9632-7c08053685d2 preserves this original rectangle; geometry was not shrunk.
Added separate PROVISIONAL20×15mm central rear exclusion, absolute X−36…−16,Y−2…13mm, UID cf2ba7b1-e510-450b-b59d-69fc7e0d80d8; all layers, STD zone,0.15mm margin. This removes possible copper/vias at prior locations(−35,10),(−20,10) while preserving header lands. Its dimensions are an explicitly conservative engineering reservation, not an asserted real antenna datum. Because it is a standalone board zone, it must be reviewed/repositioned if ESP1 is moved later. It intentionally lies below part of the ESP1 silhouette; final placement checker reports ESP1 keepout Error, retained for RF review rather than waived.
An initial custom T-shaped zone attempt produced four ROUTING_PIN_INSIDE_KEEPOUT warnings: GPIO3,GPIO8,GPIO41,GPIO42. It was replaced with the two simple positional rectangles above, without reducing the intended exclusion union. Fresh pre-route check then returned Board valid:yes,no feasibility issues. Router did not receive ignored keepout warnings on the final configuration. Original full-board stitching grid disabled; final routing has no extra vias.
Exact electrical approval needed
Live schematic read confirms GND contains U3:GND/L-R,OLED1:GND,MAX9837A:GND/GAIN, no ESP1 GND. For a later separately approved electrical correction, recommend connecting ESP1:GND::J1_22 (header J1 pin22,G/Ground) to existing GND, then re-route and re-check; it sits beside the5V pin at the USB end. J1 pin22 is officially Ground. J3 pins21/22 are also officially Ground and may be bonded to the same carrier GND to improve return access. No such schematic or copper short was made in this batch.
Library ESP1 currently exposes four GND terminals J1_22,J3_1,J3_21,J3_22, all floating in current netlist. A functionally correct return connection cannot be inferred from0 airwires because these pins are not net members. Keep them isolated until explicit electrical permission.
Remaining physical/library limits
Bought round microphone module photo is not mechanically verified against library U3's9.6×8.6mm six-hole footprint; do not fabricate until the exact variant/pitch is checked.
ESP header row22.86mm spacing and antenna projection need authoritative mating/physical verification for the exact purchased revision.
OLED and amplifier breakout variants, speaker terminal/mounting geometry, header heights and USB cable access require bought-part fit checks. Speaker retains original28.3×40.3mm envelope; no pads or holes were altered.
No manufacturing readiness or RF performance/EMC claim; tightly coupled class-D output routing/EMI testing and full audio bring-up remain downstream validation.
Reproducible verification handles
Auto-route job:auto-layout-e1ac6f11-e21a-48a1-be11-2a6120b5a40d; applied2026-10-21T14:51:45.765Z. History renders its short identifier as #auto-lay; prefer full job identifier for disambiguation.
Reads:summary inventory/placement;tree(power nets) for1.0/0.5mm routed copper;layout_image for physical relationship; routing_state(includeComputedCopper=true) for0 airwires and Bottom island; get_schematic(ESP1,GND) for isolated ground terminals.
Re-run DRC/ERC before any next edit. Keep completed routes as the base; no repeated auto-route passes were needed.
Bottom line: assigned independent layout work is persisted and all existing nets are routed, but overall device completion remains blocked by ESP1 return connectivity, RF/mechanical registration and real purchased-module fit.
Assigned scope and outcome
Routing result and fresh checks
Board, placement and manufacturing
Layer Routing Strategy
Widths, current allocations and power limits
RF exclusion: what is protected and what remains unknown