BOM data fix J1 MPN


BOM data fix only, no layout or schematic changes.
J1 (5 V input, Molex Nano-Fit 2 pin): the footprint is 1053131202 (gold) and that is the part we buy. The Manufacturer Part Number property of J1 still reads 1053131102 (tin). Set the MPN of J1 to 1053131202, manufacturer Molex, and make any related part description text say gold contacts. Do not move, re-route or replace anything else.
Then confirm the new BOM line for J1 and that DRC/ERC results are unchanged.
I’ll capture the current BOM and DRC/ERC state, update only J1’s metadata, then re-run both checks to confirm there is no design delta.
J1’s purchasing metadata is corrected in place. I’m now verifying the generated BOM line and comparing fresh DRC/ERC results against the pre-change counts.
Updated J1 BOM metadata only:
  • MPN: 1053131202
  • Manufacturer: Molex
  • Description/type: Wire-to-board / wire-to-wire connector, gold contacts
  • Footprint: CONN-TH_2P-P2.50_MOLEX_1053131202
  • Quantity: 1
No component replacement, connectivity, schematic geometry, routing, placement, or layout changes were made.
Fresh checks confirm results are unchanged: DRC remains at 18 errors and 35 warnings; ERC has no reported findings.

Independent Camera, Host CSI, and Service Interface Review
Review date: 2026-09-08
Scope: Four FRAMOS FSA-FTx/A camera connectors, Antmicro Jetson Orin Baseboard CSI host interface, and TALOS service/digital-passport interface.
Status summary

Table


ItemStatusResult
J3–J6 FRAMOS camera pin mapping✅ CompletedIndependently verified against the official FSA-FTx/A 60-pin table; power, grounds, controls, MCLK and selected 2-lane CSI mapping are consistent on all four connectors.
Camera safe defaults and support passives✅ CompletedRST_0 defaults asserted low; RST_1 and PW_EN_0/1 default high; I²C, trigger and MCLK support networks are present.
MIPI CSI polarity and impedance metadata✅ CompletedD0, D1 and clock P/N polarity is preserved; each pair is declared 100 Ω differential. No loading or protection parts were inserted on MIPI lanes.
TALOS service header and DS28E36BQ+T✅ Completed with external-master conditionHeader pinout, ESD, 1-Wire pull-up, CEXT capacitor and exposed-pad grounding verified. Added R102 to source and current-limit the previously undriven 3V3_OUT reference. External 1-Wire master must provide strong pull-up during crypto/write operations.
Antmicro host connector build⛔ Blocked / unattemptedExact Rev 1.3.4 connector mapping was recovered from the official source, but it exposes only one D-PHY clock pair per 50-pin connector. It therefore does not provide four independent 2-lane D-PHY camera inputs without an explicitly approved shared-clock or bridge/mux architecture. Exact connector MPN 68715014522 is also absent from the Flux library.
Authoritative evidence
1. FRAMOS camera connector verdicts
The installed board connectors J3–J6 are Hirose DF40C-60DS-0.4V(51), mating with the FSA adapter plug. All four use the same mapping below; substitute CAM1 through CAM4 for CAMx.

Table


FSA pin(s)Official signalProject connectionVerdict
1, 33V8_VDDCAMx_3V8✅ Correct
2, 41V8_VDDCAMx_1V8✅ Correct
5–10AUX_ANA/AUX_DIG/AUX_IF/AUX_V — Not ConnectedNC✅ Correct
11–14, 37–38, 43–44, 49–50, 55–56GNDGND✅ All twelve grounds connected
15RST_0, active lowCAMx_RESET_N, expander-controlled, 100 kΩ pull-down✅ Safe default: reset asserted
16RST_1, active lowCAMx_RST1_N, 10 kΩ pull-up to 1V8✅ Safe default: normal/high
19GPIO0 / XMASTER0CAMx_XMASTER✅ Connected
21I2C_0_SCLCAMx_I2C_SCL✅ Connected
25GPIO1 / XVS0CAMx_XVS✅ Connected
27I2C_0_SDACAMx_I2C_SDA✅ Connected
29GPIO2 / XHS0CAMx_XHS✅ Connected
31GPIO3 / XTRIG0CAMx_XTRIG through 33 Ω source series resistor✅ Connected
33PW_EN_0, high=normalCAMx_PW_EN0, 10 kΩ pull-up to 1V8✅ Safe default: enabled
34PW_EN_1, high=normalCAMx_PW_EN1, 10 kΩ pull-up to 1V8✅ Safe default: enabled
39MCLK_0CAMx_MCLK through 33 Ω source series resistor✅ Connected
51 / 53D_DATA_0_N / PCAMx_CSI_D0_N / P✅ Correct polarity
52 / 54D_DATA_1_N / PCAMx_CSI_D1_N / P✅ Correct polarity
58 / 60D_CLK_0_P / NCAMx_CSI_CLK_P / N✅ Correct polarity
Other defined GPIO, I²C_1, MCLK_1, D_DATA_2/3 and D_CLK_1 pinsOptional/unselected functionsNC✅ Intentionally unused for the selected 2-lane interface
Per-connector verdict

Table


ConnectorCameraPower/groundControls/I²C/MCLKCSI D0/D1/CLKVerdict
J3Camera 1PassPassPass✅ Correct
J4Camera 2PassPassPass✅ Correct
J5Camera 3PassPassPass✅ Correct
J6Camera 4PassPassPass✅ Correct
2. Host connector map recovered from Antmicro Rev 1.3.4
The official design uses Würth 68715014522 for both host connectors. These are the exact physical pin-to-net mappings in the reviewed source.
Antmicro J7 physical pin map

Table


PinSignalPinSignal
1CSI2_CLK_N2CSI2_CLK_P
3GND4GND
5CSI2_D0_N6CSI2_D0_P
7GND8GND
9CSI2_D1_N10CSI2_D1_P
11GND12GND
13CSI2_D2_N14CSI2_D2_P
15GND16GND
17CSI2_D3_N18CSI2_D3_P
19GND20GND
21CAM_MCLK_422CSI2_I2C_SDA_3V3
23CSI3_I2C_SCL_3V324CSI3_I2C_SDA_3V3
25CAM_PWDN526CAM_PWDN3
27CAM_PWDN428CAM0_MCLK
29VDD_1V830VDD_1V8
31VDD_1V832VDD_1V8
33VDD_1V834VDD_1V8
35CSI2_I2C_SCL_3V336CSI2_I2C_SDA_3V3
37CSI4_I2C_SCL_3V338CSI4_I2C_SDA_3V3
39CAM_RST240GND
41CAM_RST342GND
43VDD_2V844VDD_2V8
45VDD_2V846VDD_2V8
47VDD_2V848VDD_2V8
49VDD_2V850VDD_2V8
Antmicro J8 physical pin map

Table


PinSignalPinSignal
1CSI3_CLK_N2CSI3_CLK_P
3GND4GND
5CSI3_D0_N6CSI3_D0_P
7GND8GND
9CSI3_D1_N10CSI3_D1_P
11GND12GND
13CSI3_D2_N14CSI3_D2_P
15GND16GND
17CSI3_D3_N18CSI3_D3_P
19GND20GND
21CAM1_MCLK22CSI4_I2C_SDA_3V3
23CSI5_I2C_SCL_3V324CSI5_I2C_SDA_3V3
25CAM_PWDN126CAM_PWDN7
27CAM_PWDN028CAM2_MCLK
29VDD_1V830VDD_1V8
31VDD_1V832VDD_1V8
33VDD_1V834VDD_1V8
35CSI3_I2C_SCL_3V336CSI3_I2C_SDA_3V3
37CSI5_I2C_SCL_3V338CSI5_I2C_SDA_3V3
39CAM_RST040GND
41CAM_RST142GND
43VDD_2V844VDD_2V8
45VDD_2V846VDD_2V8
47VDD_2V848VDD_2V8
49VDD_2V850VDD_2V8
SoC CSI source and stuffing evidence

Table


ArrayPopulation in reviewed Rev 1.3.4Function recovered from source
R103DNPRoutes SoC CSI0_D0/D1 into J7 CSI2_D2/D3 lane positions.
R107FittedRoutes SoC CSI2_CLK/D0/D1 into J8 CSI3_CLK/D0/D1 positions.
R108FittedRoutes SoC CSI1_D0/D1 into J8 CSI3_D2/D3 positions.
R122DNPAlternate route from SoC CSI3_CLK/D0/D1 into J8 CSI3_CLK/D0/D1 positions.
The reviewed assembly therefore implements the documented mux option around CSI0x2 + CSI2x4 on J7 and CSI1x2 on J8, not a proven four-independent-camera configuration.
Why no four-camera host assignment was authored
Each 50-pin connector exposes one differential D-PHY clock pair (pins 1/2), plus four data lanes. Four independent 2-lane camera transmitters require four independent D-PHY clock pairs unless a shared-clock mode or active aggregation architecture is explicitly supported and approved. The official connector map only exposes two clock pairs total across J7 and J8. Therefore a table assigning four independent cameras to four independent SoC CSI instances would be fabricated and electrically unsafe.
Input required to unblock the host build: provide or approve one of the following:
  1. An official target-baseboard schematic/BOM/assembly variant that explicitly exposes four independent 2-lane D-PHY clock inputs and names the four camera-to-CSI assignments; or
  2. Written approval and a reference design for a specific active CSI bridge/mux/aggregator or shared-clock architecture; or
  3. A revised requirement limiting the host interface to two independent camera sources, with the exact camera-to-J7/J8 assignment and approved stuffing option.
Additionally, approve an exact Flux library part or custom part for Würth 68715014522; no exact library object was found, and no substitute/mock was used.
3. TALOS service header and digital passport
Header pinout

Table


J7 pinNetReview
1GND✅ Correct
2TRIG_IN✅ Protected by U20; 100 kΩ inactive-low pull-down; fan-out through U15 and 33 Ω source resistors
31WIRE_IO✅ U19 IO; 1 kΩ pull-up to 3V3; protected by U20
43V3_OUT✅ Corrected: R102, 330 Ω, now sources it from 3V3 and limits nominal short current to 10 mA; protected by U20
5EXT_CLK_IN✅ Protected by U20; feeds clock path through R61
6GND✅ Correct
DS28E36BQ+T support
  • ✅ U19 property MPN is DS28E36BQ+T, TDFN-6-EP.
  • ✅ IO connects to 1WIRE_IO with R65 = 1 kΩ pull-up to 3V3.
  • ✅ CEXT connects to C45 = 470 nF, X7R, 10 V; this is within the datasheet range.
  • ✅ GND and exposed pad are grounded.
  • ✅ NC, PIOA and PIOB are intentionally marked no-connect because no GPIO function is assigned.
  • ⚠️ The external 1-Wire master must provide a strong pull-up during cryptographic computation and EEPROM/write intervals. The DS28E36 operating-current requirement can reach 7.5 mA, so the static 1 kΩ pull-up alone is not sufficient to guarantee full bus voltage during those intervals.
4. Protection and termination decisions
  • ✅ No TVS, common-mode choke, AC-coupling capacitor, series resistor or other loading was added on any MIPI lane.
  • ✅ Camera CSI nets retain P/N polarity and 100 Ω differential-pair metadata.
  • ✅ Camera MCLK branches use 33 Ω source-series resistors after the clock fan-out.
  • ✅ Trigger branches use 33 Ω source-series resistors after the trigger fan-out.
  • ✅ The service interface uses one PRTR5V0U4D array for TRIG_IN, 1WIRE_IO, 3V3_OUT and EXT_CLK_IN.
  • ✅ 3V3_OUT correction: added R102 = 330 Ω from 3V3 to 3V3_OUT; calculated from 3.3 V / 10 mA.
5. Final validation evidence
  • ✅ Read-back confirms R102 connections: 3V3 → R102:P1, R102:P2 → 3V3_OUT.
  • ✅ R102 mutation resolved both newly introduced floating-pin checks.
  • ✅ Service-block read-back confirms U19/J7/U20/R65/C45/R102 connectivity.
  • ✅ Whole-schematic ERC/passive/legibility/SI review returned no reported findings except 25 Single Pin Nets.
  • ⛔ Remaining 25 errors are exactly the blocked host endpoints: 24 camera CSI nets plus HOST_MCLK_IN.
No host connector, mock header, lane swap, MIPI termination, or unapproved hardware workaround was added.
  • Status summary

  • Authoritative evidence

  • 1. FRAMOS camera connector verdicts

  • Per-connector verdict

  • 2. Host connector map recovered from Antmicro Rev 1.3.4

  • Antmicro J7 physical pin map

  • Antmicro J8 physical pin map

  • SoC CSI source and stuffing evidence

  • Why no four-camera host assignment was authored

  • 3. TALOS service header and digital passport

  • Header pinout

  • DS28E36BQ+T support

  • 4. Protection and termination decisions

  • 5. Final validation evidence