Heavy-Duty Truck ECU Design


Make me an automotive-grade heavy-duty truck ECU board with Wi-Fi, BLE, dual multiplexed CAN bus, and RS232, powered by a 24V vehicle system (continuous protection up to 30V) for commercial fleet use.
It should be a transient-hardened ECU built around an ESP32-WROOM module, featuring a single TWAI interface multiplexed across two MCP2542 CAN transceivers (5V VDD, 3.3V VIO) and one RS232 output port (e.g., MAX3232) — Dual-stage power regulation providing a 5V rail for the MCP2542/MCP3002 ICs and a 3.3V rail for the ESP32; include a main automotive connector featuring power pins, 3 active-high (positive) digital inputs, 3 active-low (negative) digital inputs, 2 analog voltage-divider inputs (0–30V scaled) connected to a 2-channel MCP3002 SPI ADC, and all remaining available ESP32 pins buffered as open-drain/open-collector outputs; apply full automotive EMC/transient best practices including 30V standoff TVS diodes on power and I/O, CAN bus split-termination and PESD1CAN protection, reverse polarity MOSFET/diode, OVP/UVLO/OCP, and EFT filtering.
Created a project doc

Truck ECU Requirements and Handoff

View Document

Truck ECU Requirements and Handoff Status
Requirements captured only. No schematic, component, PCB, simulation, sourcing, or verification work was performed for this request. The existing project context describes a USB-C WiFi BLE temperature/humidity sensor, with 45 components; it has not been converted into the requested ECU. Execution stopped because the account ran out of ACUs.
Requested product
Commercial-fleet heavy-duty truck ECU powered from a nominal 24 V vehicle supply, operating continuously up to 30 V, with transient hardening, Wi-Fi, BLE, multiplexed CAN, RS232, and automotive connector I/O.
User requirements
  • ESP32-WROOM module (exact variant unresolved).
  • One ESP32 TWAI controller multiplexed across two MCP2542 CAN transceivers, each using 5 V VDD and 3.3 ...
I saved your ECU requirements and the unresolved engineering constraints in Truck ECU Requirements and Handoff. No circuitry or PCB changes were made; your existing sensor design remains unchanged.
Key constraints: one multiplexed TWAI controller cannot monitor both CAN buses simultaneously, and automotive-grade protection requires coordinated surge ratings and qualification—not simply adding 30 V TVS diodes. Component verification, schematic design, layout, and testing remain to be done in Agent mode.
Execution stopped because your ACUs ran out.
What is Agent mode?
Agent mode lets Flux build, do deep research, validate designs, and work through complex assignments.
Chat mode is just as smart and has the same engineering knowledge, but it cannot work autonomously.
Only Agent mode consumes your plan's included AI usage (measured in ACUs).
Continue in Agent Mode

Waiting for input


Truck ECU Requirements and Handoff
Status
Requirements captured only. No schematic, component, PCB, simulation, sourcing, or verification work was performed for this request. The existing project context describes a USB-C WiFi BLE temperature/humidity sensor, with 45 components; it has not been converted into the requested ECU. Execution stopped because the account ran out of ACUs.
Requested product
Commercial-fleet heavy-duty truck ECU powered from a nominal 24 V vehicle supply, operating continuously up to 30 V, with transient hardening, Wi-Fi, BLE, multiplexed CAN, RS232, and automotive connector I/O.
User requirements
  • ESP32-WROOM module (exact variant unresolved).
  • One ESP32 TWAI controller multiplexed across two MCP2542 CAN transceivers, each using 5 V VDD and 3.3 V VIO. Verify exact transceiver ordering code, pinout, and automotive qualification before selection.
  • One RS232 output port, such as a MAX3232-based interface; serial signal count and baud rate unspecified.
  • Dual-stage regulation providing 5 V for MCP2542/MCP3002 and 3.3 V for ESP32.
  • Main automotive connector: vehicle power, 3 positive/active-high digital inputs, 3 negative/active-low digital inputs, 2 analog voltage inputs measuring 0–30 V through dividers into an MCP3002 SPI ADC, CAN interfaces, RS232, and remaining usable ESP32 GPIO buffered as open-drain/open-collector outputs.
  • Requested protection: 30 V standoff TVS devices on power and I/O, CAN split termination and PESD1CAN protection, reverse-polarity MOSFET/diode, OVP/UVLO/OCP, and EFT filtering.
Engineering constraints to resolve before implementation
  • Multiplexing a single TWAI controller provides selectable CAN access, not simultaneous independent reception/transmission on both buses. Confirm this meets fleet requirements; design safe TX/RX selection, default recessive behavior, and controlled switching.
  • Define vehicle transient and EMC qualification targets, test severities, source impedance, pulse energy, and operating temperature. Continuous operation at 30 V does not define load-dump survival.
  • A TVS with 30 V standoff clamps above 30 V. Coordinate its actual clamp voltage and energy rating with downstream absolute maxima, power-stage voltage ratings, and surge protection. Do not apply 30 V TVS devices indiscriminately to low-voltage IC pins or CAN lines; validate dedicated CAN protection against bus requirements.
  • MCP3002 powered at 5 V requires verified SPI input thresholds and output-level compatibility with 3.3 V ESP32 GPIO; add level translation where needed. Verify analog input margins, input impedance, filtering, clamp leakage, and ADC settling at 30 V and during faults.
  • Verify automotive qualification of each selected component. An ESP32-WROOM-based prototype is not automatically an automotive-qualified or certified ECU; document module suitability and qualification limitations.
  • ESP32 GPIO budget depends on exact module, reserved flash pins, boot straps, programming/debug interface, and input-only pins. Determine usable output count only after allocating interfaces and confirming boot safety.
  • Specify digital input thresholds, polarity interpretation, debounce, open-circuit behavior, shorts, and ground offsets.
  • Specify output count, voltage/current, load type, inductive suppression, fault protection, and thermal limits. GPIO buffers alone do not establish vehicle-load capability.
  • Confirm CAN bitrate(s), isolation requirements, cable topology, and whether split termination is fitted, switchable, or omitted at non-endpoint nodes.
  • Specify enclosure, connector family/pin count, IP rating, vibration, mounting, antenna placement, and grounding/shield strategy.
  • Confirm whether to replace the current sensor design or create a separate ECU project before destructive edits.
Next-session work
  1. Resolve architecture and safety-critical missing requirements; preserve the current sensor project until project destination is confirmed.
  2. Source verified datasheets and automotive protection reference designs; establish electrical, thermal, EMC, and qualification requirements.
  3. Build and check power/protection, CAN multiplexer, RS232, protected inputs, ADC/level translation, and output stages; document GPIO and connector allocations.
  4. Review schematic and power/fault budgets before proceeding to layout.
  5. Develop PCB, enclosure/interface provisions, and explicit bench/transient/EMC validation plan. Do not claim automotive compliance without supporting qualification evidence.
  • Status

  • Requested product

  • User requirements

  • Engineering constraints to resolve before implementation

  • Next-session work