Device or PCB Design


Thought for 4 mins 23 sec
Thought for 9 sec
Managing 1 task
Thought for 15 sec
Reading "mechanical-design-report" project doc.
Thought for 11 sec
3/3 Independently verify fit and remaining checks before the routing checkpoint.

Correct switch orientation and board setup; record residual keepout and capacitor findings.

Apply authorized enclosure repair pass; record repaired USB/screw access and unresolved button/assembly blockers.

Independently verify fit and remaining checks before the routing checkpoint.

Thought for 14 sec
Awaiting 1 task
Thought for 12 sec
Reading project docs.
"Desk Sign Design Review" completed.
I corrected the switch orientation and PCB setup, cleared the lid-screw entries, and added recessed USB access; results are recorded in the PCB Placement Report and Project Specification.
The design remains blocked: verification found a real switch/support collision, insufficient button travel, and obstructed diffuser installation—earlier zero-overlap results were incorrect, so I have not started routing.
Which repair approach should I take next?
1. Simplify the button and diffuser mounting
2. Repair the existing internal mechanism

Waiting for input


Project Specification
Current Repair Status — 2026-10-09
The authorized third CAD repair pass is consumed. The approved exterior form and fixed 86×30 mm PCB remain unchanged. SW1 orientation now matches top-button actuation; two-layer manufacturing-target pointer and internal programmer edge exception corrected. Six lid screw entries are cleared in body v3, and lid v3 includes recessed USB access. Nominal USB housing access passes, but selected-cable mating is UNVERIFIED.
Release remains blocked: upper PCB support physically intersects SW1; button v2 cannot provide the full switch operating travel; diffuser and retainer rear assembly paths remain obstructed. Failed coupled replacement candidates were withheld, not installed. Existing support locations and PCB reservations are unchanged; no candidate keepout changes are approved. Earlier zero-collision claims are superseded by explicit-solid tests in Mechanical Design Report cycle 3. Do not print or freeze routing from this revision.
Process remains gray PETG, 0.4 mm nozzle. Printer calibration, supplier hardware, optics and cable tests remain PROVISIONAL/UNVERIFIED. Next design decision: simplify internal button/retention architecture or authorize a further tightly scoped repair preserving current architecture. No additional geometry cycle or routing is included in this completed pass.
Project Overview
Draft prototype: a desktop busy/available sign with a single frosted illuminated window.
Intended Use
Indoor desk use. Press a button to change status; observers see red for busy or green for available.
What the Device Should Do
  • Each debounced press toggles the state once. Holding the button does not repeat.
  • Exactly one LED is on in normal operation; green at power-up (default).
  • Status is not retained after loss of power (default).
Main Features
Small microcontroller, one red LED, one green LED, one button, external 5 V supply. No display screen, radio, battery or charger.
Mechanical System Architecture
Two-piece enclosure comprising a main body and screw-fastened removable lid, plus a separate frosted diffuser insert. Board and button mount inside; USB-C is reachable from outside. Main body -> PCB and diffuser -> removable lid. Stable freestanding desk placement.
Electrical System Architecture
External 5 V -> input protection/decoupling -> microcontroller and two individually current-limited LEDs. Button -> microcontroller -> red/green outputs. USB-C is power-only; implement sink identification on both CC pins, no USB data.
Hardware Subsystems
  • Power: USB-C 5 V input, suitable protection and decoupling.
  • Compute: Microchip ATTINY402-SSNR, direct 5 V supply, internal oscillator and UPDI.
  • Lighting: one red and one green LED with individual current-limiting resistors; select diffused/wide-angle emitters for the shared window.
  • Controls: accessible momentary button with firmware debounce.
  • Debug: accessible programming connection inside removable lid.
Interfaces and Connections
Power-only USB-C, one external button, internal MCU programming connection. No communication interface required.
Power and Runtime Expectations
Continuous external 5 V operation. No stored energy or runtime target. Design within a conservative 100 mA input budget (target, not a computed consumption).
Power Tree and Power Budget
5 V input -> protected rail -> MCU and active LED branch. Only one LED active at a time. Exact rail choice, operating currents and worst-case budget to be established from selected components; no regulator assumed necessary until MCU selection.
Manufacturing and Assembly Expectations
First prototype PCB and FDM-printed enclosure. Prefer a simple two-layer board and common assembly parts. Diffuser may be cut frosted plastic rather than a print for better light uniformity. No manufacturing orders authorized.
Firmware-Relevant Hardware Requirements
Green startup state, nonblocking debounce, toggle on stable press edge only, no auto-repeat, mutual exclusion of LED outputs. Establish programmer and pin map after MCU selection; provide starter source and test procedure.
Physical Design Expectations / Mechanical Design Constraints
  • Desktop device; main body and screw-on lid.
  • Single front-facing frosted window, one accessible button, reachable USB-C port.
  • Custom rounded board outline preferred over an unmodified standard rectangle.
  • PCB envelope, holes, enclosure dimensions, screw size, LED-to-diffuser spacing, button and port coordinates remain PROVISIONAL until concept approval and sourced component geometry.
  • No battery bay or screen cutout.
Important Design Decisions
Power-only USB-C chosen for convenient 5 V power. Green startup and no status persistence chosen for simple predictable operation. Concept approval precedes enclosure CAD and electronics; schematic approval precedes layout; placement approval precedes routing.
Assumptions
Dry indoor environment, modest desk viewing distance, compact footprint, prototype rather than certified production product. Brightness and diffusion uniformity must be verified physically; two LEDs may produce hotspots without sufficient mixing distance.
Change Notes
Initial specification based on user request. Product naming completed. Industrial-design concept is the next approval checkpoint.
Mechanical First-Pass Record — 2026-10-08 (historical)
The concept was accepted. A complete separate-part CAD assembly is placed, but mechanical verification has FAILED release gates: retainer installation path, lid-screw entry clearance, and switch/support compatibility need another authorized repair pass. Do not freeze PCB placement or print for functional assembly from this revision. See project file mechanical-design-report for evidence, asset downloads and remaining work.
Datum and envelope (Estimated / PROVISIONAL)
  • Initial handoff datum: PCB XY at project origin, top surface z=0, underside z=-1.6 mm. At this historical checkpoint no actual board outline or schematic components had been created; the later placement record below supersedes that status.
  • Physical width is project X; physical up is +Y; front is -Z and rear is +Z. Desk contact is y=-21 mm. For a conventional upright presentation: world (X,Y,Z)=(x,-z,y+21) mm; this is a presentation transform only, not a PCB relocation.
  • Shell 100 x 42 x 32 mm W:H:D, outer corner R9 mm; x=±50, y=±21, z=-22.7 to +9.3. Button reaches y=23.5, giving overall height 44.5 mm including button. Scale Estimated; proportions derived from accepted drawing.
  • Intended custom rounded PCB: 86 x 30 x 1.6 mm, R3 corners; x=±43, y=±15, z=-1.6..0. All Estimated, not measured hardware.
  • Four PROVISIONAL Ø2.4 mm holes: (-39,-11), (+39,+11), (-39,+11), (+39,-11) mm; 4 mm inset from bounding corners. ST2.2 x8 screws at first two; two locating stubs at remaining holes. At least six body support locations: these four corners plus (0,±12); latter top support conflicts with candidate switch location and must be revised.
  • Reserve no-component/no-exposed-pad support regions on underside: radius 3.5 mm around corner holes, radius 3 mm at (0,±12), radius 2.5 mm at (±30,±13) for retainer contacts. These reservations were PROVISIONAL and not layout rules at this historical checkpoint; they are now instantiated but still provisional.
  • Ordinary wall 3 mm; front rim and lid skin 2.4 mm; flush stepped rear skirt engagement 3 mm, nominal radial fit 0.20 mm per side. Printer fits PROVISIONAL.
  • Generic rear/top-side height limit 4.9 mm (z≤4.9), leaving 2 mm to lid underside z=6.9, away from pads/bosses. USB exception below. Generic front/bottom-side component height 4 mm from underside (z≥-5.6), away from supports and retainer. These are Estimated design ceilings, not actual component measurements.
  • Diffuser 90 x32 x2 mm R7, z=-20.3..-18.3; one visible window 86 x28 mm R5. Bottom-side LEDs face -Z. At a 4 mm LED package height, emitter-to-inner-diffuser gap is 12.7 mm; at 2 mm height it is 14.7 mm. Optical uniformity unverified.
Port, control and hardware (PROVISIONAL)
  • Rear USB opening: rounded 9.6 x4.9 mm, R2.2, center (x,y)=(0,-6), through rear lid to exterior z=9.3. Outward/mating axis +Z; insertion -Z. Candidate vertical receptacle face z≈9.05, 0.25 mm recessed. This is perpendicular-to-PCB vertical entry, NOT a right-angle connector facing the front.
  • Candidate USB part: Molex 2047110101, 2.5 mm tabs for 1.6 mm PCB; exact variant footprint/CAD and authorized-distributor small-quantity stock NOT VERIFIED. Library 2047110001 is only a same-family mechanical proxy and has 1.4 mm tabs/recommended 0.7 mm board: do not silently substitute it.
  • Top button opening Ø12 mm, axis +Y, centered x=0,z=-5 through y=18..21. Captive printed cap Ø15 mm, nominal press travel 0.5 mm along -Y. Estimated switch actuator face (0,15,-3.35), printed stem face y=15.1, nominal gap 0.1 mm. Candidate E-Switch TL3330AF260QG mounts on the front/bottom PCB face and actuates toward +Y. Its actual mechanical fit is NOT VERIFIED; top-center PCB support currently occupies the candidate switch zone.
  • Six rear lid ST2.2 x8 screw axes at (-40,-18),(0,-18),(40,-18),(-40,18),(12,18),(40,18) mm; head-seat z=7.1, heads to z=8.8, tips z=-0.9. Two PCB ST2.2 x8 screws seat at z=0, tips z=-8.0. Simplified hardware head Ø4.2 x1.7 mm is Estimated; exact supplier screw must be checked.
  • Diffuser is retained by a removable rigid frame trapped between insert and PCB, not adhesive or a floating plate. Installed contacts are valid, but frame insertion/removal collides with body supports: release blocked.
  • Gray PETG, 0.4 mm nozzle; 0.2 mm layer height PROVISIONAL; support removal and printer fit coupons required. No screen, battery bay, vents, wireless hardware or additional controls were added in the mechanical pass; later electronics and placement are recorded below, with routing still unattempted.
Provisional PCB Setup and Placement — 2026-10-09
All 17 existing schematic parts are provisionally placed on the actual 86 × 30 mm R3 two-layer board; four Ø2.4 mm NPTH holes at (±39,±11) and all ten underside support/retainer reservations are instantiated. Wiring and values are unchanged (11 nets). The retained PCB placeholder v1 is inactive; enclosure geometry is unchanged. Routing, exports and orders were not attempted.
The stackup is 1.530 mm FR-4 core plus 0.035 mm copper on each side, giving 1.600 mm nominal copper-face separation. Exact scene transforms recover Top z=0 / Bottom z=−1.6 after subtracting the common +0.8 mm render offset. Mask and vendor finished-thickness tolerance need manufacturing reconciliation; the selected manufacturing stackup pointer still incorrectly says JLCPCB four-layer.
Selected J1 is GCT USB4960-00-C, not the earlier Molex candidate. It is Top at (0,−6), vertical +Z mating, with actual face z≈6.5 mm: 2.8 mm recess from the lid exterior, not the historical 0.25 mm estimate. Nominal J1/lid solid distance is 0.518 mm; cable reach, insertion and tolerances remain unverified.
LED1 and LED2 are Bottom at (−10,0)/(10,0), facing −Z; nominal diffuser gaps are 14.800/14.776 mm. Optics are not validated. SW1 is Bottom at (0,12.75), but functional fit FAILED: exact model-to-cap gap is 1.100 mm at rest and still 0.600 mm after the cap's full 0.5 mm nominal travel. Current footprint/model/edge-direction consistency does not establish the intended +Y actuator face. Its top-center reserved-support conflict also remains; nominal body contact had zero overlap volume, not a proven solid collision.
Final checks retain six keepout errors, one internal-J2 edge error, two C1/C2 placement warnings, twelve existing connector-driver ERC errors and four terminal-metadata warnings. No clean DRC/ERC or release readiness is claimed. The lead supplied a separate electrical-review handoff with no blocking correctness defect for compliant 5 V and single-source UPDI; dual-source backfeed, upstream D1 failed-short behavior and ESD-versus-overvoltage limitations remain.
Do not freeze placement, route for release or fabricate until the item-specific gates are resolved. See pcb-placement-report for all placements, exact nominal measurements, durable renders, review evidence and blockers. Existing mechanical retainer-path/lid-screw/printer-fit/supplier-hardware gates remain open.
  • Current Repair Status — 2026-10-09

  • Project Overview

  • Intended Use

  • What the Device Should Do

  • Main Features

  • Mechanical System Architecture

  • Electrical System Architecture

  • Hardware Subsystems

  • Interfaces and Connections

  • Power and Runtime Expectations

  • Power Tree and Power Budget

  • Manufacturing and Assembly Expectations

  • Firmware-Relevant Hardware Requirements

  • Physical Design Expectations / Mechanical Design Constraints

  • Important Design Decisions

  • Assumptions

  • Change Notes

  • Mechanical First-Pass Record — 2026-10-08 (historical)

  • Datum and envelope (Estimated / PROVISIONAL)

  • Port, control and hardware (PROVISIONAL)

  • Provisional PCB Setup and Placement — 2026-10-09