TSW-105-07-G-S Application Guide


I’ll research the Samtec TSW-105-07-G-S and write the requested application guide in the project files, with cited specifications, practical wiring and layout guidance, and verified alternatives.
I hit a service error while preparing the guide. I’m continuing with the available research and document tools; no component data has been changed.
The source checks show that current and voltage ratings depend on the mating connector and test configuration, so the guide will state those conditions explicitly. I’m also distinguishing generic contact numbering from any application-specific SWD wiring.
Created a project doc

TSW-105-07-G-S Application and Usage Guide

View Document

TSW-105-07-G-S Application and Usage Guide
The Samtec TSW-105-07-G-S is a five-contact, single-row, straight through-hole male pin header on 2.54 mm (0.100 in) centers, with 0.025 in square posts and gold-plated mating contacts. Its common use is a removable board-to-board or cable-to-board connection for signals and suitably rated power; the header itself does not define a communications protocol or a standard SWD pin assignment. Samtec exact-part page
1. Quick Specifications
Read the rating conditions, not just the number. These are connector dimensions and mated-system ratings—not semiconductor-style absolute maximum ratings. No separate semiconductor-style absolute-maximum/recommended-...
Created and verified the TSW-105-07-G-S Application and Usage Guide in the project files, covering all seven requested sections with technical citations and source links. It explains mating-dependent ratings, practical wiring and PCB layout, and two manufacturer-documented alternatives—clearly labeled as functionally similar, not verified drop-ins. Unresolved rating differences, pin-1 orientation, solder-process qualification and sourcing details are explicitly flagged; the component itself was not changed.

TSW-105-07-G-S Application and Usage Guide
The Samtec TSW-105-07-G-S is a five-contact, single-row, straight through-hole male pin header on 2.54 mm (0.100 in) centers, with 0.025 in square posts and gold-plated mating contacts. Its common use is a removable board-to-board or cable-to-board connection for signals and suitably rated power; the header itself does not define a communications protocol or a standard SWD pin assignment. Samtec exact-part page
1. Quick Specifications
Read the rating conditions, not just the number. These are connector dimensions and mated-system ratings—not semiconductor-style absolute maximum ratings. No separate semiconductor-style absolute-maximum/recommended-operating table was established in the sources reviewed; supply voltage and logic thresholds come from the connected equipment.

Table


ParameterVerified specificationClassification / application condition
Manufacturer / exact ordering codeSamtec TSW-105-07-G-S; five contacts, one row. Samtec product recordExact-part identity. Do not substitute a similar suffix without checking it.
Pitch / population0.100 in (2.54 mm), every position populated. Nominal contact geometry; the 1 spacing code is not a row count.
Orientation / terminationStraight / vertical, through-hole solder termination; blank orientation option means straight. Not a right-angle header.
Square post0.025 in square; nominal conversion 0.635 mm, commonly rounded to 0.64 mm. Mechanical mating dimension, not the required circular hole diameter.
Lead style -07Overall contact length 10.92 mm (0.430 in); PCB tail nominal 2.54 mm (0.100 in). Mating post 5.84 mm (0.230 in). Nominal geometry. Tail tolerance was not verified; use the dimensional print before tolerance-critical release.
Housing envelopeSingle-row nominal width 2.54 mm; length equals positions × 2.54 mm, giving 12.70 mm for five positions (derived). Housing height/tolerance and cut-flash clearance are not independently established here.
Housing / terminal materialPBT insulator; phosphor-bronze terminals. Materials, not an assembly-temperature rating.
-G finish10 µin gold in the contact area; 3 µin gold on the tail. General series underplate: 50 µin (1.27 µm) nickel. Distinct from -L gold-contact/tin-tail and -T tin variants.
Operating temperature, gold interface−55 °C to +125 °C. Published operating range; it does not authorize a soldering profile or eliminate current derating.
SSW/TSW product-specification current4.7 A, one pin powered per row. Product specification Rev C; applies to its mated configuration, not every possible socket/cable.
Catalog current examplesSSW: 5.7 A per pin; BCS: 4.6 A per pin; SSQ: 6.3 A per pin. Catalog qualification: two positions powered. Different published source/configuration conditions. Do not combine these into one universal maximum or multiply by five to obtain total connector current.
Working-voltage examplesSSW/TSW specification: 465 VAC. Catalog: 465 VAC / 658 VDC with SSW, 500 VAC / 707 VDC with BCS, 515 VAC / 728 VDC with ESQ. Mating-dependent ratings. PCB creepage, contamination, enclosure accessibility and the applicable safety standard can impose lower limits.
Dielectric withstand1410 VAC, EIA-364-20 test, no flashover, sparkover or breakdown; reported pass. Test voltage, not continuous working voltage.
Solder-process statementCurrent F-226 catalog states TSW: No, Lead Wave Only under lead-free solderability; HTSW is listed separately as lead-free solderable. Do not infer lead-free reflow or wave qualification from RoHS status. Confirm an approved process with Samtec and the assembler.
Typical application conditionsLow-voltage logic or power within the connected circuits' limits; no intrinsic operating supply required.Engineering application guidance, not a manufacturer-specified typical voltage/current.
Unresolved rating difference: the catalog's SSW current figure and Rev C product-specification current figure differ. Their full test-configuration/thermal-derating equivalence was not established, so this guide does not select either as an unconditional design limit. For a high-current design, obtain the applicable current-carrying-capacity report for the exact mate, loaded contacts and ambient temperature.
2. Pinout & Connections
This is a passive five-contact header, not an IC. Contact 1 through Contact 5 below are neutral schematic names; GND, VCC, SWDIO, SWCLK and reset are not manufacturer-assigned functions. The exact manufacturer-view pin-1 orientation could not be verified in the retrieved footprint evidence, so do not assume that “leftmost” means pin 1.

Table


Pin NumberPin NameDescriptionBest Practice
1Contact 1First contact in the adopted schematic/footprint numbering.Mark the chosen pin-1 end on PCB silkscreen and the cable drawing; verify the mating-view transformation.
2Contact 2Independent conductive contact.Assign the net explicitly. Tie to GND only if the interface definition assigns it to GND.
3Contact 3Independent conductive contact.For power, verify both header and mate ratings, return-current path, PCB trace capacity and power-source compatibility.
4Contact 4Independent conductive contact.For a signal, verify the connected devices' direction, voltage tolerance and any required biasing.
5Contact 5Final contact in the adopted numbering.Document use or leave deliberately unconnected; confirm continuity and that the cable is not reversed or shifted by one position.
A square PCB pad can indicate the design's pin 1; it does not make the unshrouded mating interface mechanically keyed. Continuity-test an assembled cable from board pad number to the remote connector contact before first power-on.
3. Standard Application Circuit
The standard integration is one net per contact, with a compatible five-position female socket or cable assembly. Select the mate for the square-post size, pitch, engagement depth, plating compatibility, electrical rating and mechanical retention—not just “2.54 mm.” The catalog lists several board-mating families; membership in a family alone does not verify a particular suffix or stack height. Samtec TSW family and mating information
Illustrative low-voltage UART/GPIO service header—custom assignment, not a standard:

Text


Board signal                Adopted header pin       Remote equipment
GND                         1 ---------------------- GND
VREF (target-voltage sense)  2 ---------------------- High-impedance sense input
MCU TX                      3 ---------------------- Adapter RX
MCU RX                      4 ---------------------- Adapter TX
GPIO / status               5 ---------------------- Compatible input/output
Use matching logic levels. In this example, VREF is a sense connection, not permission for an adapter to drive the board supply: do not tie two independently powered outputs together. If pin 2 must supply power instead, rename the net, specify current and direction, and provide the necessary protection/power-path circuit.
Required passives for the connector itself: none. No contact inherently needs a 10 kΩ pull-up, series resistor or decoupling capacitor. Pull-ups, source termination, ESD protection, filtering and reset biasing are selected from the endpoint circuit and cable requirements. Put IC decoupling at the IC power pins; add local bulk capacitance near a power-entry header only when the power-path/transient analysis calls for it, with voltage and inrush constraints checked.
If using this part for SWD, define and label the five-pin mapping in the board/probe adapter documentation, then apply the MCU and debugger manufacturers' reset, bias and voltage-reference requirements. The TSW ordering code does not define an Arm-standard debug connector.
4. PCB Layout & Routing Guidelines
  • Use the straight single-row land pattern. Place five plated holes on 2.54 mm centers; the derived first-to-last center span is 4 × 2.54 = 10.16 mm. The manufacturer footprint recommends 0.040 in [1.02 mm] hole diameter for the standard straight-tail layout. Specify the hole with the fabricator's plating/finished-hole convention and tolerances. Pad diameter/annular ring must meet JLCPCB's chosen process; no pad diameter is asserted here. Do not size a round hole from only the side of the square post.
  • Reserve housing and mating clearance. The derived body plan length is 12.70 mm and nominal width 2.54 mm. The mating post is 5.84 mm. Check the exact print, socket/cable body, insertion direction, enclosure and handling space before release. Do not infer mated stack height from post length alone.
  • Make the assembly solderable. Use thermal reliefs on plane-connected pads when needed for reliable hand or wave soldering; qualify spoke width/count against actual current and heating. Check bottom-side tail protrusion and clearance. Confirm the solder process because TSW and HTSW have different published lead-free solderability statements.
  • Size power paths from the load. Choose trace/pour width from current, copper thickness, layer position, permissible temperature rise and voltage drop; include return conductors, vias and thermal-relief necks. There is no universal “3 A trace width,” and the connector's current rating does not validate the surrounding PCB.
  • Route the connected interface, not an imaginary connector requirement. Keep sensitive/fast signals short and provide a nearby return path; avoid long stubs. Differential-pair routing is applicable only if assigned signals require it, and this generic unshrouded header has no verified controlled-impedance channel in this guide. Decoupling belongs at active devices, not at every header contact.
5. Common Pitfalls / Things to Watch Out For
  1. Treating a non-keyed header as a standardized or polarity-protected interface. A plausible five-pin SWD/UART mapping can still be reversed at the cable's mating view. Define pin numbering, label pin 1 and every signal, check continuity, and use a keyed/retained connector instead when reversed mating would be unsafe.
  2. Assuming pitch matching, catalog headline ratings or RoHS status make a substitution safe. Different mates, populated-contact conditions, post/tail lengths and plating options change thermal capacity, engagement and assembly behavior. Keep working voltage separate from dielectric-test voltage, resolve the catalog/product-spec current difference for high-current use, and confirm the solder process rather than assuming this PBT TSW is a lead-free reflow part.
No unconditional drop-in replacement was verified. The following are real, manufacturer-documented parts from other suppliers; common nominal hole centers do not establish fit in a particular released footprint, mating reliability or identical ratings.

Table


Manufacturer / exact partVerified common featuresImportant differences / evidenceCompatibility classification
Würth Elektronik 61300511121 in Flux, WR-PHDFive pins; straight single-row THT; 2.54 mm pitch; 12.70 mm body length. Nominal mating extension 6.0 mm, tail 3.0 mm, overall 11.54 mm, versus TSW's 5.84 / 2.54 / 10.92 mm; drawing specifies a 1.10 mm PCB hole. Rated 3 A, 250 VAC. Temperature −40 °C to +105 °C; gold contact plating. Only functionally similar. Same nominal contact centers; footprint compatibility is not verified because hole recommendations and mechanical dimensions differ. Exact Flux library match found.
TE Connectivity 3-644456-5, MTA 100 narrow headerManufacturer product page confirms five positions, one row, vertical THT solder termination and 2.54 mm pitch.Primary product record specifies 0.64 mm square post/tail, 2.79 mm tail, and matte tin mating and termination finish—not the TSW -G finish. These facts are from the TE product record. Complete mechanical/mating-post and PDF citation verification remains unresolved; no exact Flux library match was confirmed.Only functionally similar. Not qualified as an identical-plating replacement or verified footprint/drop-in substitute.
Before adding either to an approved-vendor list, compare worst-case pin diagonal against finished-hole tolerance, check body/mating clearance and pin numbering, verify the female mate's engagement and plating, and requalify the loaded-contact thermal and soldering conditions.
7. Sourcing & Purchasing Guide
Purchasing information was checked October 7, 2026. Stock and commercial terms are dynamic; this guide intentionally does not freeze a stock count or price.

Table


AttributeDetails
Primary DistributorsExact-part listings were identified for DigiKey, Mouser, Arrow, and LCSC C5993812. Samtec direct is the manufacturer route. Listing existence is not a blanket authorization claim; confirm current regional franchise/traceability through Samtec.
Packaging OptionsBulk, as stated in the exact Samtec product page packaging notes. LCSC's exact Chinese product record states bag packaging. Tape & reel and cut tape were not verified for this exact ordering code.
Standard MOQA Samtec availability row for the exact TSW-105-07-G-S states Min 1, Bulk on the TSW-105-07-L-S comparison page; that row is the -G part, not an inferred MOQ from the -L variant. The RS Malaysia exact-part listing sells a pack of 10. Distributor-specific MOQ/order multiples vary. Direct DigiKey and Mouser page reads were unavailable, so their MOQ/order multiples were not independently confirmed.
Sourcing AdvicePrefer Samtec direct or currently franchised distributors with traceable manufacturer packaging and certificates where needed. Non-authorized marketplaces can introduce counterfeit, re-marked or mixed-plating stock. Specify TSW-105-07-G-S exactly: -07 fixes geometry, -G fixes finish, and final -S fixes one row. -RA, -LL, -D or a numeric omitted-position suffix changes the delivered configuration. Verify packaging and full code on both the quotation and purchase order; do not treat a suffix change as merely a commercial packaging change.
Information not established: full current-derating equivalence between the two Samtec sources; exact pin-1 view orientation; all mechanical tolerances; an approved solder profile for the intended factory process; unconditional cross-manufacturer drop-in compatibility; complete TE PDF/mating-post verification; and distributor-specific MOQ/order multiples where direct pages could not be read. These are verification gaps, not claims that the manufacturer documents omit the information.
Sources
This guide documents application practice only; it does not certify the current Flux symbol, footprint, 3D model, or an assembled board.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources