I’ll research the Samtec TSW-103-07-G-D and write the application guide in the project files, with cited ratings, practical wiring guidance, and clearly qualified alternatives.
I verified Samtec’s 4.7 A rating applies with one pin powered per row—not all six contacts loaded—and the header itself has no fixed signal assignments. I’m distinguishing the AVR ISP example from the connector’s generic pinout and flagging the mechanical details that remain unverified.
The Samtec TSW-103-07-G-D is an unshrouded, vertical, through-hole 2×3 male pin header with a 2.54 mm (0.100 inch) pitch and 0.635 mm square posts, used for board-to-board and cable-to-board interconnections (Samtec configured product page). A common use for this six-position geometry is a classic AVR SPI in-system programming (ISP) connection; this is an application-defined assignment, not an intrinsic Samtec signal pinout (Microchip SPI programming adapter documentation).
Created the TSW-103-07-G-D Application and Usage Guide in the project files, covering all seven requested sections with citations, AVR ISP wiring guidance, alternatives, and sourcing information. Unverified mechanical details and replacement compatibility are explicitly flagged; the next priority before fabrication is checking the exact footprint and mating fit.
The Samtec TSW-103-07-G-D is an unshrouded, vertical, through-hole 2×3 male pin header with a 2.54 mm (0.100 inch) pitch and 0.635 mm square posts, used for board-to-board and cable-to-board interconnections (Samtec configured product page). A common use for this six-position geometry is a classic AVR SPI in-system programming (ISP) connection; this is an application-defined assignment, not an intrinsic Samtec signal pinout (Microchip SPI programming adapter documentation).
1. Quick Specifications
This passive connector does not have semiconductor-style supply rails or an IC Absolute Maximum Ratings table. Manufacturer connector ratings describe a specified interconnect system; they must not be mistaken for unconditional limits for every socket, cable, ambient temperature, or contact-loading configuration.
Table
Parameter
Value
Classification / conditions
Connector / mounting
Male header, vertical, unshrouded, through-hole solder termination
TSW–SSW product specification §3.1; not a six-contacts-simultaneously rating.
Voltage rating
465 VAC
TSW–SSW product specification §3.2; not a recommended logic voltage or a mains-safety approval.
Operating temperature, gold plating
−55 °C to +125 °C
Manufacturer operating range, §3.3; keep the complete assembly within its lower applicable limit.
Typical application voltage
Target MCU supply, commonly 3.3 V or 5 V
Application examples only. Select the actual voltage from the target MCU and programmer specifications; the header neither regulates nor translates it.
Absolute maximum supply / typical quiescent current
Not applicable to this passive header
Do not invent an IC-style VCC limit or supply-current specification.
Rating reconciliation: Some distributor and older catalog entries quote different current and voltage values. Use the rating for the exact mating pair and its stated test/loading conditions rather than choosing the largest number. The verified TSW–SSW specification used here is revision B, November 15, 2018.
2. Pinout & Connections
All six contacts are electrically independent: Samtec does not require any contact to be VCC, GND, RESET, or a data signal. The table below is the standard six-pin AVR SPI ISP application assignment, supported by Microchip’s SPI header mapping, and must be implemented deliberately in the schematic and PCB footprint.
Table
Pin Number
Pin Name
Description
Best Practice
1
MISO / PDO
Target-to-programmer serial data
Connect to the target’s documented ISP data-output pin, not merely any pin labeled SPI. Ensure other bus devices release the line during programming.
2
VTG / VCC
Target voltage reference
Connect to target VCC. Treat it as voltage sense unless the particular programmer explicitly supports powering the target; prevent two supplies from driving each other.
3
SCK
Programmer-to-target serial clock
Connect to the documented ISP clock pin. Keep the route direct and select programming frequency according to the target datasheet.
4
MOSI / PDI
Programmer-to-target serial data
Connect to the documented ISP data-input pin. Avoid contention from shared application circuitry.
5
RESET
Active-low target reset control for classic AVR ISP
Allow the programmer to pull RESET low. A 10 kΩ pull-up to target VCC is a useful starting choice, subject to the device/programmer requirements; see §3 and its verification note.
6
GND
Common reference
Tie directly to target ground; provide a low-impedance return path.
Numbering discipline: Establish pin 1 from the manufacturer drawing, then verify schematic pin → footprint pad → mating cable conductor continuity. A bottom-side view mirrors the mating-side view; do not assign numbers solely from an unlabeled drawing or a generic library symbol. This guide does not certify the current Flux footprint’s numbering or dimensions.
3. Standard Application Circuit
Classic AVR six-pin ISP header
Wire pins 1, 3, 4, and 5 to the MCU’s documented MISO, SCK, MOSI, and RESET programming pins; connect pin 2 to target VCC and pin 6 to GND. Microchip identifies pin 2 as the target voltage reference and pin 6 as common ground in its SPI programming adapter documentation.
The connector itself requires no passive components. The following are target-circuit provisions, not requirements of TSW-103-07-G-D:
RESET bias: Use 10 kΩ from RESET to target VCC as a starting design choice. AVR042 states 4.7 kΩ or greater for STK600 programming and at least 10 kΩ for debugWIRE; confirm the selected MCU and programmer before finalizing. Do not automatically add a RESET capacitor: AVR042 excludes it for debugWIRE and PDI. These recommendations were read from the manufacturer document via web extraction; independent citation-backed PDF verification remains pending, so treat the detailed numeric recommendation as not fully verified in this guide. See AVR042, §3.
Supply decoupling: Follow the target MCU datasheet. A 100 nF ceramic close to each MCU VCC/GND pair is a practical starting choice, not a connector specification; add bulk capacitance based on supply impedance and load transients. AVR042’s web-extracted guidance calls for one decoupling capacitor per supply/ground pair, placed close to the MCU; PDF verification remains pending. See AVR042 §2.
Shared SPI signals: Prefer peripherals that are high impedance while the MCU is held in reset, and keep their chip selects inactive. Where external circuitry can drive the programming lines, provide isolation chosen for that circuitry—Microchip explicitly calls for series resistors in this circumstance, without prescribing one universal value (AVR910 online RESET section). Do not insert an arbitrary resistor into every line without checking loading and timing.
Power ownership: For a self-powered target, use VTG for the programmer’s reference. If programmer-powered operation is supported, define the power source and any isolation/jumper arrangement explicitly; Microchip documents both target-powered and programmer-powered approaches in AVR910.
This example applies to AVR devices with SPI ISP, not automatically to UPDI, PDI, TPI, JTAG, or Arm SWD. No LED resistor calculation, USB CC resistors, or shield connection applies to this header.
4. PCB Layout & Routing Guidelines
The following are engineering recommendations, except where a manufacturer dimension is explicitly cited:
Use the actual mechanical footprint: The double-row pattern is 2.54 mm along the rows and between rows. The extracted recommended hole callout appears to be Ø1.02 ±0.08 mm, but its evidence validation failed; this hole diameter and tolerance are unverified. Obtain the current Samtec footprint drawing before manufacturing, and coordinate finished plated-hole size, annular ring, and drill compensation with the fabricator. Do not treat the nominal square-post width as the required round-hole diameter.
Preserve mating access and orientation: Leave space for the actual socket/cable housing and insertion/removal, not just the plastic header body. Mark pin 1 clearly on silkscreen and assembly documentation; keep nearby tall parts out of the insertion path. The unshrouded geometry is not a substitute for a keyed connector.
Ground and solderability: Connect the GND contact to a solid return network. Use thermal relief where needed for reliable through-hole soldering to a plane, and ensure its spokes also support the intended current; avoid a large unsolderable heat sink or an undersized thermal bottleneck.
Power routes: Size trace width, copper pours, vias, and thermal spokes for actual current, copper thickness, and allowed temperature rise. Do not infer a universal trace width from the connector’s 4.7 A conditional rating, and do not assume six loaded contacts can each carry that value.
Signal and capacitor placement: For ISP, route SCK/MOSI/MISO directly over a continuous ground reference and avoid unnecessary stubs. These are single-ended signals: differential-pair routing is not required. Keep MCU supply decoupling at the MCU power pins, not at the header simply because power crosses it; any higher-speed use of this header needs its own signal-integrity assessment.
5. Common Pitfalls / Things to Watch Out For
Reversing the cable or mirroring the footprint. An unshrouded 2×3 header can be connected in the wrong orientation. Trace every pad to its cable conductor, label pin 1, and check continuity before applying power. This can misroute VCC/GND as well as programming signals; do not assume a standard-looking header already implements AVR ISP.
Treating family ratings or shared-bus wiring as unconditional. The 4.7 A rating specifies one powered pin per row, not every contact loaded. In an ISP application, a peripheral driving the shared bus or a reset circuit that the programmer cannot assert can prevent programming; use the MCU/programmer requirements and Microchip’s contention guidance, rather than adding arbitrary pull-ups or capacitors.
6. Popular Alternatives & Equivalents
Two independently manufactured alternatives are listed below. Neither is certified here as an unconditional drop-in replacement. Matching 2.54 mm pitch alone does not establish plated-hole fit, contact engagement, body clearance, plating suitability, or equal current/temperature capability.
Manufacturer product listing identifies a six-pin straight THT dual header, 2.54 mm family, 3 A, 250 VAC, −40 °C to +105 °C (Würth WR-PHD dual series). The exact PDF’s web extraction indicates a 6.0 mm mating post, 3.0 mm tail, and recommended Ø1.10 ±0.15 mm holes, but independent PDF verification remains pending.
Functionally similar; same nominal 2×3 interface. Pin mapping and exact footprint compatibility require drawing/library comparison. Lower published current and temperature capability; do not use as a rating-equivalent substitute.
Verified Flux library record identifies six contacts in a dual-row through-hole header; Amphenol’s series drawing gives a 5.84 mm mating length, 2.41 mm tail, and 10.80 mm overall terminal length. Exact full-part decoding was not independently validated in the drawing; current ratings/lifecycle were not verified for this guide.
Functionally similar; nominal pin-grid match according to the library. Not certified footprint-compatible or drop-in; compare pad numbering, lead fit, shorter tail, housing, and electrical ratings before release.
Qualification procedure: Compare the latest exact-MPN drawings, plated-hole tolerances, pin numbering, body keepout, mating depth, tail length through the actual board thickness, plating system, temperature range, and loaded-contact ratings. Purchase samples and test mating and soldering before approving a second source.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Buy directly from Samtec, or check exact-MPN listings at Mouser and RS. Confirm authorized status and regional ordering terms with Samtec. Mouser’s page could not be read because of its access restrictions; no Mouser stock or MOQ is asserted.
Packaging Options
Samtec’s exact-MPN page specifies Bulk. Do not assume tape-and-reel or cut-tape availability for the unsuffixed part.
Standard MOQ
Samtec’s exact-MPN page lists minimum 1 piece. The reviewed RS regional listing sells packs of 10; MOQ is supplier-specific and must be reconfirmed at checkout.
JLCPCB assembly option
Exact-MPN listing C6339671 exists. Confirm current inventory, through-hole assembly support, and the selected service’s conditions before designing the build around it. JLCPCB states purchased parts are retained for PCBA orders and cannot be shipped separately. Its “Full Reel” field does not override Samtec’s bulk packaging specification.
Sourcing Advice
Use manufacturer-direct or franchised channels with lot traceability; avoid untraceable marketplace stock. Match TSW-103-07-G-D exactly: contact count, lead style, plating, and row suffixes affect the part. Do not accept a single-row, right-angle, different-height, or different-plating variant without engineering approval. Confirm the actual packaging format, order multiple, lead time, and mating connector separately.
No live price or stock guarantee is made. Distributor search results can be cached; obtain a current quotation before ordering.
Sources
Manufacturer documents and primary application references are listed explicitly to make the guide independently auditable:
Samtec configured product:TSW-103-07-G-D. Exact geometry, nominal post dimensions, finish description, and bulk/minimum-order information. No page revision/date stated.
Samtec product specification:TSW–SSW specification, revision B, November 15, 2018. §§3.1–3.3 provide the cited conditional current, voltage, and temperature ratings.
Samtec recommended PCB layout: “Recommended P.C. Board Layout for (X)TSW Single, Double, & Triple (Thru-Hole & Right Angle),” attached to this part’s datasheet records and accessible through the product page’s Footprint link. Revision/date and direct canonical footprint URL were not verified. The pitch and row spacing are verified; the hole callout is not.
Samtec series print, manufacturer-authored distributor mirror:TSW series drawing. Detailed lead-style table and tail plating lookup remain pending; no unverified table values from it are treated as production requirements.
Microchip AVR042:AVR Hardware Design Considerations. Web extraction reports Atmel-2521R, 09/2016; independent PDF evidence verification remains pending for the detailed reset/decoupling guidance and revision.
Amphenol manufacturer drawing, mirrored with the Flux library part:2304140030_Amphenol-ICC-67996-106HLF_C412086.pdf. Cited terminal lengths verified; document revision/date and exact-part decoding not verified.
Verification boundary: This is an application guide, not a certification of the current Flux part model or a manufacturing release. Before fabrication or approving a substitute, resolve the unverified hole tolerance, exact footprint numbering, lead-style tolerances, tail plating, and replacement fit; verify the selected MCU/programmer requirements for the example circuit.