SRP4020TA-4R7M Usage Guide


I’ll research the manufacturer’s datasheet, verify alternatives and purchasing options, and save the application guide in the project files with citations and clearly marked uncertainties.
Thought for 16 mins 3 sec
Thought for 7 sec
Created 3 tasks.
1/3 Verify Bourns SRP4020TA-4R7M electrical ratings, terminal connections, and mechanical data.
Accessed knowledge for the next task.
Thought for 1 min 7 sec
Awaiting 1 task
Thought for 13 sec
2/3 Verify two or three alternatives, Flux library availability, and distributor packaging.

Verify Bourns SRP4020TA-4R7M electrical ratings, terminal connections, and mechanical data.

Verify two or three alternatives, Flux library availability, and distributor packaging.

Write and check the cited Application and Usage Guide in project files.

"SRP4020TA-4R7M Usage Guide" completed.
The guide is drafted. I’m checking the current-rating definitions and tightening the alternative-part and purchasing recommendations before finishing.
Created the SRP4020TA-4R7M Application and Usage Guide in the project files, covering all seven requested sections with citations, sourcing details, and two Flux-linked functional alternatives. Unverified footprint dimensions and source limitations are explicitly flagged; neither alternative is claimed as a drop-in replacement. Before substituting, verify the land pattern and your converter’s peak and RMS current requirements.

SRP4020TA-4R7M Application and Usage Guide
The Bourns SRP4020TA-4R7M is a shielded, two-terminal 4.7 µH surface-mount power inductor with a carbonyl-powder core, intended for switching power conversion. A standard use is the output energy-storage inductor in a buck DC-DC converter, where selection must consider both peak-current/DC-bias behavior and RMS-current heating.
1. Quick Specifications

Table


ParameterVerified value / conditionRating classification
Manufacturer / MPNBourns SRP4020TA-4R7MIdentification
Inductance4.7 µH at 100 kHz, 1.0 V, 25 °CNominal
Inductance tolerance±20%Production tolerance
Q10 minimum at 100 kHz, 1.0 VMinimum test benchmark
Self-resonant frequency27 MHz typicalTypical, not a guaranteed minimum
DC resistance95 mΩ typical; 105 mΩ maximumTypical / maximum
Irms2.6 A, defined at 40 °C temperature riseThermal current benchmark, not a destructive absolute maximum
Isat3.5 A, defined at 20% inductance dropDC-bias benchmark, not a destructive absolute maximum
Operating temperature−55 °C to +150 °C, including self-heatingOperating range
Storage temperature−55 °C to +150 °CStorage range
ConstructionShielded; carbonyl-powder core; enameled-copper wire; Sn terminal finishConstruction
QualificationAEC-Q200 compliant; RoHS compliant and halogen freeCompliance
PackageTwo-terminal SMD with lead-frame terminations; a Product Dimensions drawing is provided. Exact body dimensions and tolerances could not be verified from the readable drawing evidence.Package type verified; numeric dimensions unverified
Recommended land patternA manufacturer Recommended Layout drawing is provided. Exact pad dimensions and spacing were not reliably readable; copy them from the original drawing before footprint creation.Drawing available; numeric transcription unverified
Terminal pitchNot specified as a single pitch value in the validated evidence; use the full land-pattern drawing.Unverified / not applicable as a connector-style pitch
Voltage ratingNo component operating-voltage or absolute-maximum-voltage rating was found in the validated Bourns specification. The 1.0 V figure is the inductance test signal, not a circuit voltage rating.Not published in the verified table
The datasheet also notes that PCB trace size/thickness, airflow, and cooling affect component temperature; verify temperature in the end application. The operating-temperature ceiling includes self-heating: the full Irms test current is not automatically usable at the maximum ambient temperature. The manufacturer's carbonyl-powder core specification takes precedence over the project's existing ferrite-core description; this guide does not modify that metadata.
2. Pinout & Connections

Table


Pin NumberPin NameDescriptionBest Practice
1Terminal 1 (schematic convention)One end of the winding. The manufacturer schematic does not assign polarity.Connect to either side of the intended series current path; in a buck converter this is commonly the regulator switch node.
2Terminal 2 (schematic convention)Other end of the winding; electrically nonpolar.Connect to the other side of the series path; in a buck converter this is commonly the filtered output node.
“Terminal 1” and “Terminal 2” are schematic/footprint numbering conventions, not intrinsic SW and VOUT pin names. The inductor is nonpolar, so reversing it does not change its ideal electrical function; do not ground either terminal unless the selected converter topology explicitly requires that connection.
3. Standard Application Circuit
A standard buck converter places the SRP4020TA-4R7M between the regulator’s switching node and the regulated output; see Texas Instruments' buck power-stage application note for the generic topology. The inductor is only one element of the converter; capacitor values, feedback network, bootstrap capacitor, compensation, and any catch diode must follow the chosen regulator’s datasheet and topology. The following placement and selection recommendations are engineering integration guidance, not a Bourns reference design; exact passive values cannot be established without the regulator, input/output voltages, switching frequency, and load requirements.

Text


VIN ── CIN ── GND
 │
 └── Buck regulator SW ── L1 SRP4020TA-4R7M ──+── VOUT
                                               |
                                              COUT
                                               |
                                              GND

FB divider: VOUT → regulator FB → quiet ground, per regulator datasheet
Optional diode/BOOT/compensation: only where required by that regulator
  • Input capacitor: place the regulator-recommended ceramic/bulk input capacitance directly across VIN and power ground to minimize the high-di/dt input loop.
  • Output capacitor: choose capacitance, voltage rating, ESR, and ripple-current capability from the regulator stability and transient-response requirements. Place it close to the inductor output and regulator return path.
  • Current selection: estimate the converter’s worst-case inductor ripple with the regulator manufacturer’s equation and worst-case VIN, VOUT, switching frequency, and minimum inductance. For continuous-conduction operation with triangular ripple, the generic peak-current relation is Ipeak = IOUT,max + ΔIL/2. Check peak current against the 3.5 A Isat benchmark with design margin; Isat only marks a 20% inductance reduction, not failure. Also consider startup, load transients, and the regulator's maximum current-limit tolerance rather than checking nominal steady-state load alone.
  • Thermal selection: calculate inductor RMS current over the real load profile and compare it with the 2.6 A / 40 °C-rise benchmark. Then validate case temperature on the assembled PCB because copper area and airflow change heating.
  • Loss check: first-order winding loss is Pcu ≈ IL,rms² × DCR. Use maximum DCR for a conservative room-temperature estimate and account for copper resistance increasing with temperature. Core loss must be checked separately when switching frequency and ripple are high.
4. PCB Layout & Routing Guidelines
  • Use the current Bourns recommended land-pattern drawing. Exact pad dimensions remain unverified in this guide; do not recreate the footprint from distributor body dimensions alone.
  • Place the inductor immediately beside the regulator SW pin. Keep the SW-to-inductor connection short and compact; avoid enlarging noisy switch-node copper merely for heat spreading.
  • Route the inductor/output-capacitor/load current path with low resistance and few vias. Size copper for the application current and permitted temperature rise rather than applying an arbitrary universal width.
  • Avoid narrow thermal-relief spokes on pads carrying substantial converter current unless assembly constraints demand them; confirm solderability and current capacity together.
  • Put CIN close to VIN/PGND and COUT close to the inductor/output return. Route the feedback sense from the quiet output node, away from SW copper and the inductor’s high-field edges.
5. Common Pitfalls / Things to Watch Out For
  1. Treating 2.6 A Irms and 3.5 A Isat as interchangeable “maximum current.” Irms is a 40 °C temperature-rise benchmark, while Isat is the current at a 20% inductance drop. Remedy: check both worst-case RMS heating and peak/ripple current, add margin, and measure temperature and ripple on the real PCB.
  2. Substituting by 4.7 µH alone or using a poor switch-node layout. A replacement can differ in DCR, bias curve, rating definition, height, footprint, qualification, and loss; excess SW copper or a long loop increases EMI. Remedy: requalify electrical/thermal behavior and land pattern, then keep the hot loop and SW-to-inductor connection compact.
These are functional alternatives, not claimed drop-in replacements. All are two-terminal, nonpolar power inductors, but package, land pattern, height, current definitions, DCR, qualification, and temperature range differ.
  • TDK SPM4020T-4R7M-LR — Available in the Flux library. The manufacturer product page confirms 4.7 µH ±20% at 100 kHz, 128 mΩ typical / 147.2 mΩ maximum DCR, 2.5 A typical at 40 °C rise, and 3.5 A typical at 30% inductance reduction. Its stated operating range is −40 to +125 °C including self-heating. Compatibility: same two-terminal topology; functionally similar; footprint compatibility is unverified and it is not a verified drop-in. Compared with Bourns, allow for higher winding loss, a lower thermal-current benchmark and temperature ceiling, and a different inductance-drop criterion. These TDK figures were independently checked on the manufacturer's product page; the catalog PDF could not be citation-validated during this research.
  • Würth Elektronik 74404043047A — Available in the Flux library. It is 4.7 µH ±20% at 100 kHz/1 V, with 2.3 A rated current at 40 K rise, 1.43 A typical saturation current with a less-than-30% inductance-reduction criterion, and 46 mΩ ±20% DCR. Its 4.0 × 4.0 mm body and 2.5 mm maximum height differ from the Bourns part. Compatibility: same two-terminal topology; lower-current functional alternative only; footprint compatibility unverified; not a drop-in. Its much lower saturation-current benchmark makes it unsuitable for an unchanged design operating near the Bourns current ratings; consider it only if actual peak current and height clearance permit.
For every substitution, rerun the converter’s peak-current, RMS-temperature, ripple, efficiency, EMI, and transient checks, and compare the complete manufacturer land pattern and body keepout before changing the BOM.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsDigiKey, Mouser, Arrow, and LCSC listings were identified on 2026-10-07. Recheck stock, price, lifecycle, and ship date at order time.
Packaging OptionsManufacturer standard packaging is 3000 pieces per 13-inch reel. The LCSC listing also specifies “3000/Full Reel.” Confirm cut-tape or custom-reel availability directly with the chosen distributor; these options were not independently confirmed from a readable DigiKey listing.
Standard MOQThe LCSC listing starts at 1+ piece, while its full-reel quantity is 3000. Manufacturer reel quantity is also 3000 pieces. A distributor's one-piece retail minimum is not the factory reel quantity; verify other distributors' MOQ separately.
Sourcing AdviceBuy from Bourns-authorized or established distributors where practical. Match the exact SRP4020TA-4R7M suffix, 4.7 µH value, ±20% tolerance code, SRP4020TA package/series, and desired cut-tape or reel packaging. For optional JLCPCB assembly, check the exact BOM match and current availability at ordering time; do not assume the web listing guarantees assembly stock. Treat marketplace parts with unverifiable provenance/date code cautiously.
Sources
Research date: 2026-10-07.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources